Counting matching models…
Cooling Base for the GMKtec G3 Plus Mini-PC I designed this, completely toolless cooling base, to increase air-flow through the mini pc via an auxiliary 120mm PC case fan. I used a spare Arctic P12 connected to a USB adapter. Added…
An improved top fan for the GMKTEC K6. The fanmount.stl is desiged for the noctua NF-A12x25 5V PWM fan that can be directly connected to the internal mainboard with a little modification (the wires on the connector have a different…
I was asked to add a fan grill to the GMKtec Pro case by @RazziaDK. Because Noctua are so great, I went with their high efficiency grill fan, scaled down to fit 92mm fans.
This drop-in replacement lid elevates the lid about 10 mm above the top-fan thus allowing for a much better airflow of the RAM/SSD cooling. I have measured more than 10K (10°C) difference on full power for DDRRAM temperature and 5K for…
GMKtec NucBox G9 bottom modkit heak sink + modkit (60mm 2ea) → temparature under 65℃ (default fan setting) models: modkit - plain modkit - 60mm 2ea (max. 15T) modkit - 80mm (max. 15T/25T) foot m2 bracket m.2 ssd bracket (REQUIREMENT)…
This case has been designed to replcae the lid of the GMKTec G3 Plus (Intel N150) to give active airflow to the NVME and RAM. Numerous variations/combos available: 80mm and 60mm fans 25mm and 15mm fan heights Enclosed or flat for mounting…
his modification is to install two 8010 fans in the side covers to replace the original fans. Based on the original design, modified the covers. Update 15.08.2025 : Added an updated version for the 8025 fan. The processor-side fan has…
Extend the height of the GMKtec G3 Plus by around 14mm to a total ground clearance of 16mm, providing greater airflow for the CPU fan intake underneath. A quick and crude CPU stress test resulted in a 4°C drop in the 'balanced' mode -…
Vertical stand for Gmktec K8 plus for better Fan effectivity and airflow
This is a cooler for the GMKtec Nucbox G9. It replaces the SSD access door and reuses the original hardware. I used this fan and the hardware that it comes with.…
Vertical Stand for the GMKtec “NucBox” G3 Plus Mini-PC This model derived from my “Cooling Base” design, because the Mini PC - in it's default orientation - builds up a lot of heat below the lid. Having it propped up vertically creates a…
The GMKtec M5 Pro (and Plus ) comes with a small 40mm fan on top - it's quite noisy. This top/case allows you to add a 92mm fan instead. You can either have the fan on top, or extend the case and keep the fan inside. I intend to use it…
mini pc stand 10 inch
Mount for a NucBox5. It retains access to all ports except the security lock and permits airflow as these little guys can burn themselves up pretty easily otherwise. The holes are 4mm and it is a snug fit, so adjust anything you need to…
All credit to user Curon for the original model. This case is designed to stand vertically . If you prefer horizontal orientation, use the original model. Material: PLA Case & Stand Infill: Gyroid, 15%, layer height 0.2mm. Inserts: 4x M2…
This is a 3D-printed rackmount frame designed for the GMKtec Mini PC (model 3 Plus) — but it can also accommodate other compact mini PCs of similar size. The design features: Modular 3-bay layout — holds up to three mini PCs side by side…
G3 or G3 plus lid models with 120/92/80mm fan mount. 120mm has a small loop for zip tie for fan cable management.
I wanted to make a very compact recording/streaming PC and this is what I came up with. I used a Uctronics UC-747 HDMI adapter, Uctronics UC-586 (but any 800x480 5 inch screen with the same tabs should fit), and an Acasis VS-041 /…
Items in the pictures: GMKtec NucBox G3 IOCREST M.2 PCIe3.0 to 8 Ports SATA 6G Multiplier Controller Card B/M key Mini SAS SFF-8087 right angle to 4 SATA 7P 180 degree ICY DOCK ToughArmor MB998SP-B 8 Bay 2.5" SATA Cage FSP Flex ATX 300W…
For those who want cooling your nucbox G5, it could fit for you. It is also some cables can be easily aligned at the bottom. File name "1.5mm" or "5mm" is indicate corner guard hight. “5mm” ver. could steady hold. but may weak against…
Please note that I am not a professional designer; this is a hobby project. You do everything at your own risk. Commercial use, selling prints or files on Etsy/eBay/etc. is NOT allowed without my written permission. You will have to…
No skill required, print and put on.
Update 12.25: Fan bracket and mounting plate for the original fan have been redesigned. This now also allows the installation two of NVMe drives with heatsinks. Update 12.25: Lüfterhalter und Platte für originalen Lüfter überarbeitet.…
No skill required, print and put on
Hello, This part allows you to install a 120mm fan on the GMKTec K6 and two SMA or RP-SMA antennas for better WiFi and Bluetooth connectivity (the antennas supplied with the device are very poor quality, especially for Bluetooth). You…
Base for improving cooling under the GmkTec mini-PC - K8 plus
This is a mod-kit for installing an 8010 sized cooling fan on the GMKtec G9. The fan must be installed using M3(head diameter: 5.2mm, total length: 4~6mm) screws. This model has an expansion compartment for cable and connector storage.…
I designed this as a side wall mount for my G5 as there are no ports on the left side and I wanted to have it stored under my desk. It's a pretty simple design and a simple print. The easiest way is to print the whole model upside down…
This is a 2 piece mount for a GMKTec Mini PC. This is a 2RU mount meant for a 10inch server rack. This model does not require any support when printing. I suggest printing in PETG since the PC can get hot. Additional parts needed: M3*4*5…
Kühlsystem für GMKTec NUC K8 Pius Die Lüfter halten ohne Schrauben in den Druckteilen. Nach den Lötarbeiten die Lüfter in die Druckteile drücken. Oben saugend, unten pusch. Die Schrauben für das Unterteil befinden sich in den Gewinden für…
Allows you to hang a GMKte N100 Mini-PC on an IKEA Skadis pegboard. Use two M2 screws to attach the mount to the back of the PC (the holes are already there), and voila. I might have gone a little overboard with the pegs, but doesn't use…
Slide in for the GMKTec G3 Plus mini PC for use with @mseidler_2335608 's Intel NUC 10 inch 3U rack mount. https://www.printables.com/model/1204831-intel-nuc-10-inch-3u-rack-mount
DISCLAIMER, this is my first ever attempt at designing anything and this was made on TinkerCAD. Wanted to add extra cooling to my G5 mini mini PC since it always on running some containers. It does a great job on it's own but since I had…
GMKtec NUC G5 PC TPU Cover to protect the PC surface when traveling
Printable computer case for the GMKtec G2 Plus mini pc. Print case body with tree supports for best results. Top and bottom plates do not require supports
This is a simple leg replacement to use where the existing soft legs are. This was created to help with the airflow of the PC and allow for better intake at the bottom. The legs fit into the recessed area where the existing soft feet are,…
Simple model to hold the GMKtech Nucbox G5 onto an extrusion. Use m5 screws to mount.
This leg helps the mini PC cooling on the underside. The TPU leg is not important to print. UPDATE: v2.0 model allows you to open the bottom door without dismount the leg.
An adaptation of the GMKtec Evo X2/T2 under-desk mount to fit the 10-inch rack standard (UMS - Universal Modular Shelf). This remix combines two source models: The rack-mounting structure/base comes from the Lenovo M90q Gen 3 / M80q M70q…
Insert direction indicator Easy detaching handle on the side Port accessible independent while other is covered
This mounting bracket screws to the M2 holes on the underside of the GMKtec Mini N150 G3 Plus and provides two 5mm holes for screws to mount to a surface. Model is designed to be attached with two M2x8 Cap Head screws. Print with organic…
Small mounting bracket for the Gmktec k6 8845hs to fit a Noctua NH-L9x65 to it. NOTE: will require copper shims under the cooler and standoffs at the corners. (Snug fit) 118.50mm x 109.50mm x 4.0mm (LxWxH)
I designed this minimalist VESA mount because I couldn't find an existing option that felt secure without requiring the removal of the rubber feet. This bracket features a high-clearance design that snaps directly onto the unit for a…
Slide in for the GMKTec G2 Plus mini PC for use with @mseidler_2335608 's Intel NUC 10 inch 3U rack mount. https://www.printables.com/model/1204831-intel-nuc-10-inch-3u-rack-mount
This is a mounting plate for the GMKtec NucBox5 mini PC. The mini PC has two M2 screw holes on the bottom, which I use to attach the plate. The plate itself provides two positions for M4 hexagon nuts, allowing it to be mounted with the…
Custom mounting bracket tailored specifically for the GMKtec NucBox G3 / G3 Plus Mini PC. Perfect fit without blocking any front ports, power button, or ventilation slots. In addition i left a small hole on the bottom for airflow.
I was annoyed at the hot air from my eGPU blasting out to the right, when I was gaming. This stand holds the eGPU so the hot air is sent upwards. It does not improve or worsens the thermal performance. But it saves space. I also made a…
Simple mount for GMKTec G3 mini pc to rest on top of a Orico 5 Bay enclosure without sliding from side to side. Slots into the G3's slot mount holes and just rests on top of the Orico. Doesn't prevent forward/back movement, just…
Add up to 4 additional NICs to your G9. Huge thanks to @sleeeeeepy_3195269 for the original case design! Read more about it on catskull.net AI Disclaimer: I used Claude (Opus 4.8) to modify the original 3MF files. Files:…
This is a concept multirotor frame from the free Concept Drone Generator at uamkt.com/build/generator. Enter a mission (bird monitoring, mapping/survey, recon/security, cargo) and a payload; the generator sizes an airframe class,…
An all-in-one custom enclosure designed to clean up your desk or home lab setup. It perfectly fits the GMKTec G3 Mini PC along with additional networking and storage hardware. Features: - Dedicated slot for GMKTec G3 Mini PC - Space for…
Description This project is a modular, 3D-printable storage rack designed to hold up to six 2.5-inch SATA SSDs in a compact homelab setup. The holder is designed for use with Intel SSDs, including the Intel SSDSC2BX800G4R, and is intended…
A nice and Clean 10" Rack mount for the GMKtec EVO-X2, fits neatly, doesnt move, gets enough cooling and makes the GMKtec look less cheap.
English version below. Dies ist ein verlängerter Ersatz (70 mm) für ein "Aluprof Halter MKS" da es diese nur in der Standardlänge von ~40 mm zu kaufen gibt. Die Originale stehen wohl zu sehr unter Spannung und können brechen. Keine…
I was asked to add a fan grill to the GMKtec Pro case by @RazziaDK. Because Noctua are so great, I went with their high efficiency grill fan, scaled down to fit 92mm fans.
This is a simple leg replacement to use where the existing soft legs are. This was created to help with the airflow of the PC and allow for better intake at the bottom. The legs fit into the recessed area where the existing soft feet are,…
This is a small addon to GMKTec G3 that allows fitting 2.5'' SATA SSD and Fan on top to cool said SSD and the original Nvme and memory. I used it with M2 SATA to SATA adapter below: EDIT: M2 Sata Adapter Converter | M2 Ngff Sata 7pin…
This case has been designed to replcae the lid of the GMKTec G3 Plus (Intel N150) to give active airflow to the NVME and RAM. Numerous variations/combos available: 80mm and 60mm fans 25mm and 15mm fan heights Enclosed or flat for mounting…
An improved top fan for the GMKTEC K6. The fanmount.stl is desiged for the noctua NF-A12x25 5V PWM fan that can be directly connected to the internal mainboard with a little modification (the wires on the connector have a different…
Print the top cover in anything you like and the feet in some sort of TPU. The top cover is held in place by friction, so the tolerance is small. To reduce the chances for the feet to break easily, increase the walls to 5 and infill to…
I was annoyed at the hot air from my eGPU blasting out to the right, when I was gaming. This stand holds the eGPU so the hot air is sent upwards. It does not improve or worsens the thermal performance. But it saves space. I also made a…
3d Print: ABS No Supports Note did not model the spacers as I had 5mm high spacers Parts: Noctua NF-P12 redux-1700 PWM MT3608 Boost Converter (set to 10V, mainly because the fan flows plenty of air and prefer not to hear fan noise)(Hot…
I purchased the GMKTek m6 plus to act as a little plex server to sit in the livingroom so i wanted to add a noctuna fan to keep the volume at a good level. I also like retro gaming and I have recently revisited my youth with lightgun…
I designed this minimalist VESA mount because I couldn't find an existing option that felt secure without requiring the removal of the rubber feet. This bracket features a high-clearance design that snaps directly onto the unit for a…
I am CAD Kim, the manager of the DCinside Minipc Gallery, a leading mini PC community in South Korea. The mod kit I am uploading this time is for the GMKtec G3 mini PC. It is a modular assembly kit that allows for the attachment of a…
I'm Kim CAD, manager of DCinside Minipc Gallery, It is a mini PC community that represents South Korea. You can find my channel here: Kim_CAD on YouTube The modeling I am uploading this time is GMKtec's M6 case full size modeling. The…
Small mounting bracket for the Gmktec k6 8845hs to fit a Noctua NH-L9x65 to it. NOTE: will require copper shims under the cooler and standoffs at the corners. (Snug fit) 118.50mm x 109.50mm x 4.0mm (LxWxH)
Adapter lid with fan mount for GMKtec G3. You can use Noctua NF-A6x25 or any 60mm fan (its height is not limited).
Not so small mount for the GMKtech nucbox m3 to mount it to the wall and its bigass power brick. Notes- The case is intended for #4 screws with 40 pound wall anchors. The lid is intended to use m4 sized machine screws up to 17mm in…
The original one is running too hot for the NVME Storage. It's higher now, but can feet 2 40mm fan 1 extra fan if needed to help cooling the CPU Need 8 magnets, 2x 2 mm, to clip the back piece to the chassis. NVME are not mounted, the…
When Jeff Geerling published his review of the GMKtec G9 NAS box , I knew I could get this thing to work a little better for myself - So I got one, chucked an aluminum heatsink on some SSDs I had laying around and created this vertical…
A cooler case for the GMKTec G9 If you. like me were in the market for a cheap, not to fancy, NAS you might have bought the GMKTec G9. On paper it looks awesome. However the case design leaves a lot to desire. Have a look at Jeff…
Print standing vertically (hole for device oriented up-down) with support. Ensure cooling slots are aligned with vents when mounting device.
Extend the height of the GMKtec M5 Plus or K6 by around 12mm to a total ground clearance of 16mm, providing greater airflow for the CPU fan intake underneath. No additional hardware required. The existing feet friction fit into the stand.…
This is a small addon to GMKTec G3 that allows fitting 2.5'' SATA SSD and Fan on top to cool said SSD and the original Nvme and memory. I used it with M2 SATA to SATA adapter below: EDIT: M2 Sata Adapter Converter | M2 Ngff Sata 7pin…
his is a custom-designed replacement top cover plate for the GMKTEC G9 Mini PC . Whether you're upgrading airflow, personalizing the look, or replacing a missing plate, this model gets the job done cleanly. Included with the download is…
80mm Fan Mod Kit for GMKtec M5, M6, K6, K9 mini pc. This mod kit allows you to replace the stock top cover, which has a noisy fan and provides poor cooling for the second SSD. Since the fan grill design is just a scaled-down version of…
Vertical stand for NucBox with mount for IKEA Skadis with dovetail cutout for easy access. Comes in two parts and can be printed directly on bed with support for the IKEA Skadis mounts or screw holes. The vertical stand is made so that…
1.5U - 10" Rack for GMKTec M5/M5Pro Mini PC. 2 versions, 1 with and 1 without keystone holes. Can be printed on Prusa Core One. Profile: 0.20mm Structural Material: PETG/ABS/ASA Infill: 15% Gyroid Perimeters: 3+ Bottoms: 4 Tops: 5
Print the top cover in anything you like and the feet in some sort of TPU. The top cover is held in place by friction, so the tolerance is small. To reduce the chances for the feet to break easily, increase the walls to 5 and infill to…
When installing one needs to move the Wifi and bluetooth antennas. I suggest moving these trough the keylock hole and placing them outside the case. The fan easily snaps in place in existing mounts from original fan.
3d Print: ABS No Supports Note did not model the spacers as I had 5mm high spacers Parts: Noctua NF-P12 redux-1700 PWM MT3608 Boost Converter (set to 10V, mainly because the fan flows plenty of air and prefer not to hear fan noise)(Hot…
I picked up a GMKtec K11 to be part of my home lab and was extremely underwhelmed with the original top/lid that came with it. I noticed that it restricted airflow so much that it created a noticeable whistle/whine sound. I designed this…
Original cooling fan for this computer is a tiny whiny noisy fan. This top lid allows for 80 mm slim (10 mm tall) fan to be mounted inside without increasing the height of the PC. SSD without a heatsink can still be installed even in the…
I purchased the GMKTek m6 plus to act as a little plex server to sit in the livingroom so i wanted to add a noctuna fan to keep the volume at a good level. I also like retro gaming and I have recently revisited my youth with lightgun…
Easy mount for GMKTec NucBoc 3 series to mount on to a display stand. You need 2 velcro cable tie (10-12 mm wide) or some zip tie. (Screws already included with the machine in their original package.) Leaves the air intake mostly…
10" rack tray for mini PC, model GMKtec k12, with 5 keystone for usb, hdmi and ethernet. recommended: walls: 4mm layer height 0.2mm filling: 15% All upgrade photos when print finish.
GMKtec G3 ethernet port to, Adds port for a m.2 ethernet cards port.
I am CAD Kim, the manager of the DCinside Minipc Gallery, a leading mini PC community in South Korea. The mod kit I am uploading this time is for the GMKtec G3 mini PC. It is a modular assembly kit that allows for the attachment of a…
![Flexi Mini PC Port Cover [GMKTEC K8 Plus, K11]](https://media.printables.com/media/prints/fe0e73c2-5487-4b72-a199-5dc3cfe3be85/images/10316062_29fa35c4-0884-493d-9472-08e0c4762710_b4b0c998-6b9d-41bd-9efd-937b18808f05/mini_pc_cover.png)
