Counting matching models…
These are all the parts I created to mod the Prusa Lack enclosure V2 to fit the ender 3. Most of the parts can be found in the Prusa build here: https://www.prusaprinters.org/prints/3673-prusa-enclosure-v2-mmu2s Wood screws:…
Reupload of Beaver Works 's great work that he uploaded to MakerWorld The official Snapmaker top cover costs a whopping $249 ... and my wallet simply did not approve of that purchase. So, I had to take matters into my own hands and create…
Liked the drawer unit but thought the hexagon pattern adds some flavour to it and saves a tonne of filament.(50% off shell,25% off drawers). I added a slight angle to feet so it stops harassing me for supports. I printed it flat on its…
Made some changes to the nubs on the side of the latch so it does not have any sharp edges, when I printed mine, the first time I used it broke the sides of the box. Reduced the size of the nubs by .15 mm as well. Printed on lime green…
As requested, a remixed design to allow a better fit with free floating tubes AND scaled up by 110% to allow Magpul M-Lok hardware to fit. Slightly more difficult to print though, but not impossible with the right slicer settings. I ended…
A remix of the wonderful Chevy Chase Advent House by mcmaven (2023 version) I changed only a few parts, you need still the original parts by mcmaven For the walls: you can just print them faced down and add a filament change, no…
Just a Super cool upgrade I found on here and adapted it for my needs... It works but not as tight as the bolt in version as I had troubles with the screws not staying tight now it could have just been a me problem but if this can save…
This is a reinforced version of the great Accessory holder by albrnick. I tried 2 times to print and use the original version, but accessories cause a breaking on the support between the two holders after a couple of weeks. So I edited…
This is a DIY starter kit, you NEED a base model Kidztech 1/6 Yamaha and you WILL have to cut parts of it and add hobby grade electronics for this to work at all ! I can help for difficult parts, just ask in the comments APRIL 2019 UPDATE…
Ner Lner brake van wagon model rail moddel train wagon
K1 Max top mounted filament spool holder modded to use vented raiser from NorcoT https://www.printables.com/model/623798
This is a combination of Nathan Builds Robots ('s?) Modder Board Front Cover (extra clearance version) and Bananenminister 's vertical ribbon cable guide. NBR's MB Front Cover is mirrored because the hole prevented me from moving the…
I had a cardboard spool of this filament lying around and couldn't find one that fit https://www.amazon.com.au/gp/product/B0B5GQFGJ8/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 So I downloaded JamKo76's awesome design but after…
I don't charge for my functional models. Please consider purchasing some of my paid models as a way to support both my work, and this great website: https://www.printables.com/@ninjamida/store Check out my other AD5X replacement parts,…
Changes from the original model by 3d_bubbles on Thingiverse: This 3-rail Picatinny mount for the Bug-A-Salt 3.0 was almost perfect as-is, but I wanted to ensure things stayed in place with an additional angled extrusion if there's…
Not much modded really just made the sides 202mm x 3mm inside, added a bit of chamfer around the outside. PLA-CF, 0.2mm, no support.
Printed using PETG with 100% infill and 0.20mm layer height. Anx256 created a great model for replacing the back of the AOOSTAR WTR Pro to allow for the use of a 140mm fan instead of the stock 120mm fan. This remix adds a 140mm version of…
This is a component set for the VXE VGN Dragonfly R1 ( NOT SE, Pro, Pro Max). The main purpose is to provide tools for making 3D printed mice using these internals. I've provided the STEP and F3D. The Fusion file is reasonably-well…
The mini control horn is used on many of the smaller Flite Test designs. I took the original design and made the slight modification of beveling the part that is inserted into the foam so it is a little easier to push in. I also added a…
it is a nice model for you to have and looks very good.
This is a variation of the Nathan Builds Robots Modder Board Front Cover (extra clearance version) that has been modified to work with my 30mm chain links. (See my models for reference). This cover clears the left stand and aligns the…
i wouldent printit I just used it for cad pouropses
I was sick and tired of the massive VFAs of the original LDO nema14 motors so I did the “Voron V0.2 Nema 17 mount” mod, but now the tophat and backplate did not fit anymore. So….. I modeled all neccesary parts to not only make the tophat…
(SF bolt checked: works with the SF bolt ) do you like the FGC-9 MKII stingray butt-stock? and would like to use this on a non stingray FGC-9 MKII model? then I have here a remodelled version to the buffer tube. this download only…
I've added the improved pulley body module and combined it with my own pulley body mod. This is only for use if you're using the DIY MMU2+1S mods. Print instructions No supports needed. Print using PetG for longer lasting and use 25% to…
This box is a remix from nickelbeee's DJI mini2 Travel box. Thanks Nickelbeee for the great design! I use a phone case when I hook up to the mini2 controller, so I have a few part printed to help with holding a thicker phone. And I wish…
Please refer to the original model page for full details, as the only difference in this version is the location of the main fan. Ensure you cut only the marked fins and seal the fan with tape, as I have removed the screw holes to achieve…
Fits this housing: https://www.printables.com/model/1453676-dji-o4-o3-lens-mod-housing Still fits the O3 camera. Thanks to LorenzFPV for the alternate versions!
Original by Stew675 modified for a better redirect of airflow by adding internal ducts, slightly adjusting fitment, and beefing up the arms to better prevent deformation from material creep. This should be a bit more effective at…
I made this mod mainly due to the fact that razors with contoured handles tend to twist sideways and slip through the gap. The added notch helps prevent this.
Printed with White PLA+ eSun (230°/60°) on a Creality Ender 3 V3 SE. The goal was to make a first prototype before doing it in PETG or another material more suitable for a computer piece. For now it fits very well and can hold fans. I…
Original Model Found Here I took iListen2Sound's modified model of the ‘NathanBuildsRobots Modder Board Front Cover’ for the Sprite Extruder (the extra clearance model) and cut some material from the top to make it a flat surface so that…
I love Prusa Research, their company philosophy and mindset. However, I do like my printers clean and logo free though, so i adapted my top mounted LCD to not show any logos. I also deletd the speaker cutouts, as the speaker is already…
It fits almost perfectly with my power cable (photos) i THINK if you have a diffrent cable it will fit better. I recommend to print it with PET-G for stability. If you have problems with putting it on your table, try making some lines…
its a pip sword segemented.
This is small mod of file stealthburner_printhead_dragon_rear_cw2 from orginal Stealthburner head, for fit with Voron Tap module. where four screws, mounting vertical MGN9 carriage, interfere with printhead rear housing. The one and only…
I wanted better temps for my system so i modded a duct for fresh air intake and a mount for 2x 120mm fans in the bottom. For the 2x 120mm Fan shoud in the bottom you need to cut out some parts that are in the way and also need to remove…
Small improvements that I found helped with RapidMonster's model: Geneva_Driven - Shortened so it does not protrude past the Central Gear. This stops looser bearings from popping out during assembly on a flat surface. The hole for the…
This is an OpenSCAD model that generates custom wall plates in any single and multi-gang combination: Blank Toggle Switch (Takes up entire plate) Duplex Outlet (Takes up entire plate) Rocker/Decora Plate (Takes up entire plate) Keystone…
Updated to print in less than 2hrs. Cleaned up to handle 8.5x11 sheet of transparency film and a change to the bottom support to accept the thin film. Uses 3 hooks so that a paper hole puncher can be used on the shield transparencies.…
Heyya all, So, this is my first attempt at making a movable 3d print so it's not perfect. I made it have End caps for the movable parts so it should be gluten-free, but I'm not 100% sure about the fit. this should be like a little really…
PubHubs (PublicHubs) Features -These blocks provide 11mm of lift/lower (flip block over for lowering) and can ride stock height -Cooling fins (how effective are they really? idk they look cool) -Due to being open source, can be customized…
my first upload i apologize if ive made any mistakes and welcome advice from anyone more experienced, this is a great design by someone else ive adjusted to meet my requirements maybe it'll be useful to someone else
this model of a modded corvette stingray is based on one i have in nfs unbound.
This is a variation of Gennro's ATX PSU Bazzite Box design. The project files include: Raised letting that can be printed in a different color. A STEP file for you to add any lettering or designs if needed. Double fan side Mount (this is…
For Hyper PLA cardboard spool adapter for K2 Plus CFS Just tear off oneflange of the cardboard spool : Place printed flange and attach the wire on it: Turn and tear off the other side of cardboard spool and place the other printed flange…
This design is a remix of Magne's “Weekclock with planetary gear" . I had some issues with the original design files (especially it did not fit my clockworks…), so I made some modifications and decided to publish the result here. Changes…
This is a moderator stick from Gorilla Tag and is highly recommended! Credits to Dollarheadset545.
This bracket allows you to install two 3.5" HDDs anywhere you'd like. Intended for computer case modding. Make SURE you print two of these, one NEEDS to be a mirror of the other. This is easy to do in your slicer software. You'll need a…
Remix: removed clips added cap collar to hold parts together slight geometry tweaks to allow easier printing (print both parts laying horizontally, with supports for 'cap' for screw gap and collar) Category: Hand Tools
I've fixed the funnel at the bottom of the MEGA version, since it had a step in it that required supports to be printed correctly and prevented the correct sealing via o-ring. Print it as per Sillybutts instructions: 5 walls and 15% infill.
This is a lengthened Silly SCAR that allows you to fire Mega darts instead of Mega XL! Why? Well, because I like my faux “suppressors”, and I have a ton of Mega darts and basically no Mega XL. And hey, your gamemode may use Mega XL as a…
All credit goes to Josef Prusa and his team or whoever create this RamBo board cover for the Original Prusa i3 MK2S. I pretty much just extend all the vent holes on the cover for maximum cooling for the RamBo board. Therefore, it should…
Loved the simple and solid design that Mulilla made, but I found that the left locking tab was very delicate. I replaced the tab with a thicker tab, without the locking knob. The locking function isn't needed anyhow and now the tab is…
Ultra small Pocket antenna mod. Does not use the original antenna, use spare from ELRS receiver. Back clips into place. Print in ABS or better.
Modded top for MiSTer case V2 Taki Udon Mega Pack version. Added Mister Logo
Based upon another model but I built this version from the ground up: https://www.printables.com/model/925614-cr2-wired-battery-replacement This variant has 2 separated entry points of the cables, less shorting. I've adjusted the…
Changed some settings so i could print it on a 300x300 printer (K1 Max) faster with less glueing
Video https://www.reddit.com/r/ErgoMechKeyboards/comments/1lfq5bh/modded_naya_wip/ Naya Keycaps – Original Designs These keycaps were created from scratch for the Naya, a custom ergonomic split keyboard. They’re uniquely shaped to fit the…
Camar/Forest 801 cabinet hanger covers modified to be longer and with wider skirt. I printed mine with PLA, standing on the skirt using tree support. Step file attached so everyone can tailor for own needs.
I modded the original design to taper towards the top to better fit a Chinese stealth bomber frame profile. This is mounted on the underside near the forks. Using a SVMC72150 controller. I also increased the height of the base piece by…
I used the original step files from Ratrig to create this mod. It was hard to get the magnets into the stock magnet mounts for all front / top panels. So I decided to make them “enclosed” to the printed files. I printed the parts with…
This is a modded gearbox for the SandPiper 1:8 (by Black Crow) to fit a SCT Sidewinder. This motor is high KV (3800), so i run and 2S, with greater gear ratio, and smaller 95mm tires. With this configuration, this is drivable, the motor…
All credit goes to Josef Prusa and his team or whoever create this RamBo board cover for the Original Prusa i3 MK2. I pretty much just extend all the vent holes on the cover for maximum cooling for the RamBo board. Therefore, it should…
NOTE: although this design works very well, there is a new revised version of it at https://www.thingiverse.com/thing:3687678 , with more flexible options for the duct and overall orientation. I'd recommend using the new version if you…
I never liked the shroud that came with my V-minion kit. It was flimsy and small. I took one of the simplest designs found on the EVA 3 page and modified to fit the EVA 2 carriage. It's a lot sturdier and works with the 2 color designs. I…
Support for fixing the MMU buffer on top of the Enclosure. Top plug with 5 holes for the filament pipes.
Had to move the two mounting holes over 1.5mm so that this shroud could live nicely with my BL-Touch mount - other than that, it works great. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2…
Apart from making the middle part thicker I took used the pinmod and m4 mod from these people. Putting in in one download. 5mm carbon rod 2.5cm long can be inserted and the tension pulls it behind the ridges making sure they won't come…
This part relocates the cr-touch probe so there is no longer a y-offset between nozzle and probe. Zero y-offset means no movement of the bed during probing, which should result in a more precise mesh. This will only work if you've already…
the Only Hiby Case i found for 3d printing. thought it was an awesome case but than thought it would be kool to see the lower half of the player too. I like how the back of the player looks so i removed the lower part. I had no idea how…
Display Mount for the V0.2 R1 I added extra length to the top part of the Mount as the original did not fill the small gap between the frame and display. helps to give a super clean look.
Removed the gap for the thermistor connection.
A case for a USB drive, made to be as small as possible. I got the PCB from an old USB, the driver is a ChipsBank CBM2199. PCB needs its side cutouts enlarged a little with a file to fit. Then it slots into the case and it closes up.…
a new version of my ptfe plug, this will help with the feed angle (45 degree up/down/left/right) to avoid the rubbing that my original sometimes got depending on the filament. A benefit of this new design is it is suitable for feeding the…
No instructions as this is a mod from another listing. The only thing I would recommend would be to us flat screws so the heads don't stick out and possibly interfere with the chain. If possible. See the other persons 45 degree cut photo.…
Slightly modded version, added some holes and removed the integrated fan guard. Category: Electronics
Here is the step file from my modded V-Core 3.1. All mods are in the component “Grizzly mods” 01: CPAP CNC - I already uploaded this mod, you can find it here…
Multiuse Bracket for modding parts onto the simrig, basically just a base so you can add platforms to put things as keyboard, controllers, even a base for flight simulator controllers, free to imagine, posting both the bracket with the…
Search for: N2830 11 1000KV 270W on ebay or AliExpress. on: https://bitbucket.org/compactpcbmaker/cpcbm based on: https://bitbucket.org/compactpcbmaker/cpcbm/src/master/mechanics/head/head_4p2.stp Modded Source file will follow when…
All files are based on the originals provided by the manufacturer. When printing, follow the Letter-Number code format (e.g. A1, A2). If a code appears more than once, you must choose which version you want to use. When more than one copy…
Use the spacers to keep the mounting boards high enough to clear the lower fan. Added a mounting board for bitaxe gamma with holes to mount 40mm fan on back using 3mm screws.
Another in my series for makers to earn achievements for their dedication to 3D printing. Model prints with 10% infill. Supports recommended for the the trophy, arms, ribbon and star. Arms recommended to be printed upside down and…
I liked the slim design of PJR's build, but to fit it on my ender 3 backplate i had to modify the fit. My ender 3 has 2 posts for fixing the original hot end in place and the holes on the back of the slim weren't deep enough or wide…
Added funnel on top for easier dice throw. Made slighty larger.
After I bought the RetroCultMods solderless kit, I got tired of seeing the cable hang out of the big square hole where the RJ11 port used to be. So I decided to design this to solve that problem. I used the original screws that came with…
Just posting my modded centauri carbon , would be cool to see your guys modded centauri carbon in the makes / comments , all creators have been credited below , im just posting how my carbon looks , i do not claim to be the original…
more RGB for more FPS??? 😁😂🤣 Rafts: YES for LED Lens Supports: NO Nozzle: 0.4 Resolution: 0.16 - 0.28 Infill: 10% Scale your needed size in your slicer! Print LED LENS in PLA in White or transparent and vertical with brim function
There are different models included. keep in mind that you need to use long keys to install the bolts. this is a modded version of Umbraged Whisper shroud. since I liked the look of it a lot. there are besides the different top rail…
As i was helping and working with Cronis on his mod, we had some different ideas on some parts. We agreed that i will make my modded parts as public available remix of his mod. As we both will continue to work on his great mod, we will…
The original model of the Mega Modded Silly Scar only came in a 3 line version, so I added a 6 line version using the Silly Scar Simple Redesign model. I have had great success using the 15% infill, 5 walls profile recommended by the…
Estes 2003 SDI Satellite Kit Nose Cone modded for printability Should be the original scale. separated into pieces and threading added. no support needed I print with 3 top 3 bottom 0.2mm layers 2 walls 5-10% infill (as light as you can…
A set of fender delete components (centers+spacers) compatible with onewheel XR/+ and funwheel. This particular set matches the edge geometries of the Huff Designs PubPad or my remixed “Pushy” version. The “center” pieces allow for the…
So I was making a conversion on an old World Tour guitar for a colleague. I decided to use the original motherboards screws etc so I made a holder for the Pi Pico I used. It fits nicely and you can run all the wires and dual SW520D as a…
USB and USBc Front IO panel for Mac Pro 1.1 "cheese grater" mod Front IO panel replacement for Mac Pro case conversion. It fits two USB-a ports and one USB-c port. [no audio jack because I couldn't find an HD audio cable with a single…
The top cover will need to be downloaded from the original model. I mainly redesigned this case to allow me to adjust the brightness of the LEDs with a button on the side and provide some mounting options for the arduino nano. PCB Design…
