78 models
I wanted to make some head skins for Lucky 13 from the game Stray since they look so much alike. I recommend you print the heads in as high of quality you can, with seams set to random and without supports. The heads should be oriented on…
It is a simple 3d model easy to print in up-right position on standart 0.2 layer height prints in about 1 hour
Top and bottom bins to fit into the center console of the Mitsubishu Outlander PHEV model. I printed the top bin upside down with a lot of support for the bottom, which gives a rough inner bottom surface which is fine to avoid parts…
Switch plate to mount a push button in a spare slot on the dash. This is for a 2020 Mitsubishi Outlander PHEV. I would imagine it would be fine for most Outlander models and maybe other Mitsubishi cars. I use this push button on mine to…
My knob bezel cracked so I thought I may as well design and print a new one. I used snug supports which seemed to work the best. I also recommend using ironing on all top layers for a smother finish. There are 2 models, Outlander4WD is…
Заглушка крепления поводка передних дворников Mitsubishi Outlander 3 (рест.3). При чистке снега отвалилась. Хорошо, что углядел в снегу. Т.к. вероятность ее потерять имеет место быть, то по-быстрому ее замоделил, распечатал, примерил -…
The aspect ratio may not match for different holders, you will have to play around with the slicer.
Hi, Cup holder adapter for both Redbull & Coca-cola box. Fits in my Outlander 2016 mod PHVE. Outer Diameter: 79mm hight: 60mm Redbull D: 54mm Coca-cola: 67mm Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No…
Like my similar design for Polaris , this is a wrench used to remove and re-tighten the fuel ump retaining ring on an ATV. In this case, the wrench is designed specifically for a Can-Am Outlander 570 EFI, but as before, I am sure there…
Trashbins is the most overlooked feature missing in cars. Use this frame to fit a plastic bag in the midconsole, so you can hold your car tidy. Fits Mitsubishi Outlander 2019-2022 (please give feedback if it fits other models as well,…
These printable files prevent your Mitsubishi 4wd and seat heaters from being pressed by accident.
This gland can be used for the DC supply lines Versions With supports: The “skirt” and added layer above that covering the 6mm hole enable a print without further support. If the perimeters are printed from the inside out, the O-Ring…
Rather than using the dubious keyhole slot on the rear of the charger to attach the charger to a wall I decided to create a wall mount cradle. This cradle allows the charger to be easily and securely slid into place on the wall. The slot…
I've created this armrest insert to aid in keeping things more organized in there. Box size is 120 x 167 mm and the brim is 128 x 171 mm. Brim size can be increased by about 6mm all around (3mm per side) if you want a snugger fit. The…
Kennzeichenhalter vorne zum Anbau an den Frontbumper Can Am Outlander G2 Rohrdurchmesser 32mm Print instructions ABS empfohlen, ASA geht auch.... 2x Schraube M6x35 2x Mutter M6 2x Scheibe M6
I made this Microphone adapter for my Lancer because i really wanted to have the microphone at the original location for my aftermarket head unit in my case its for pioneer but most microphones you can buy on ebay are made the same way...…
Schalterhalterung zur Montage von 3 Druckschaltern an einer Outlander. Zur Schaltung von Nebelschlussleuchte, Lightbar usw. Verbaut sind 19mm Druckschalter der Marke Keenso Bezugsquelle Amazon Print instructions PETG mit Farbwechsel 0,25…
Adapter für die Rücklichter von Shin Yo um sie in die Lampenhalterung einer Can Am Outlander G2 einzusetzen. Ebenso Adapterplatten für Reflektoren um sie einzusetzen. Print instructions PETG mit wenigstens 4 Perimetern, 0,3 reicht.…
🔧 Mitsubishi Outlander PHEV 2014 – Deep Headlight Dust Cap for LED Upgrade Designed to solve LED headlight clearance issues This model is a deep / extended headlight dust cap created for Mitsubishi Outlander PHEV (2014) , intended for…
Versions With supports: The “skirt” and added layer above that covering the 6mm hole enable a print without further support. If the perimeters are printed from the inside out, the O-Ring groove can be printed without supports as well.…
Versions Blank: If you don't want to use the port, you can put in the blank plug to seal it off. M16: For small diameter cables as in the original application this gland is sufficient. Currently all versions are universal, so you can plug…
I had those Aliexpress 10.26 inch AA/Carplay displays and I wanted a much cleaner mount than the factory option. Seeing the included mount have double sided tape and then just plopping it on top of the dash and the cherry on top was that…
Replacement plug for Mitsubishi Outlander III (PHEV) GG2W 2014 RHD. I lost the original plug off road. Hooked with a branch or stone on the road. The part is located on the bottom under the front passenger seat. I couldn't find the part…
This gland can be used for the Signal cables Versions M16: For small diameter cables or Bulgin PX connector (or similar). M20: For larger diameter cables. Waipu SP21: If you want to replace the original connector with a 7- or 9-pin Waipu…
I've used Xblitz phone holder with charger but unfortunately the sticky rubber used to hold it in place didn't work well due to textured surfaces in the car. This is a replacement for the base of the charger - I guess with slight…
I find new G3L Outlander radiator is vulnerable to take sticks inside radiator. So I wanted to make metal cover. I added dxf model for plasma cutters. Also included measurements wher to bend it to make it fit. No need new holes. It fits…
Can Am Outlander G3L work light mount Hardware 30-35mm M3 bolt to work as hinge pin. 2pcs M6 bolt to fix mount around bumper tube.
This is the cable gland for the 230V power input for the Outlander Charger. Versions With supports: The “skirt” enables a print without further support. If the perimeters are printed from the inside out, the O-Ring groove can be printed…
Can-Am (715006097 ) LinQ 30 US Gal (139 L) Trunk Box to Fit without removing rear rack. I bought this box for my atv. It was annoying that it needed to remove rear rack to make this fit in linq system. I made adapters that make it…
Designed plastic parts for the Estes Rocket Outlander #2110 Modified the tail cone to allow the modification for a 24mm D engine mount tube. Category: Models
Versions M16: For small diameter cables as in the original application this gland is sufficient. M20: This is the largest possible option. Waipu SP21: If you want to replace the original connector with a 7- or 9-pin Waipu SP21 connector.…
Secondary winch switch for Outlander G3L This takes Warn mini switch inside. I Installed snowplow tilt to work via this switch.
Заглушка отверстия для разблокировки АКПП Mitsubishi Outlander III рест.3. У многих, в т.ч. и у меня, она была утеряна "
Tiskněte s plnou výplní (kdyby něco nesedělo ať se to dá doladit např. úhlovou bruskou či nožem)
I'm installing the turn signal fascia on my Can-Am Outlander. The 2 little running lights are pretty expensive for what they are. I chose to use some universal 3/4" lights. The lights fit the hole, but are very loose. I printed the washer…
These are replacement Protection Plugs for the plastic racks on my Can-Am outlander 2004. I bought a second hand ATV which had 3 of those broken so Modeled these quick and they work like a charm. Print Settings Printer Brand: Creality…
This data can be useful if you want to use the Mitsubishi Outlander Rear Motor for your DIY EV conversion and need the exact location of the mounting holes in relation to the front mounting surface. Files Mounting Plate: can be…
When you want to utilize the Mitsuibishi Outlander AC Compressor in your DIY EV conversion, you will have to create a bracket to mount it. Due to it's shape, getting the bolt pattern is not super trivial since they have different heights…
Заделал себе защелку подлокотника с удлиненным зацепом. Если в подлокотнике много барахла всякого лежит, он, бывает, не защелкивается. Отсканировал, сделал модель как со стандартной длиной зацепа так и с увеличенной на 10 мм. Вдруг надо…
The original heater motor has the 19mm cooling pipe, the Luzar motor LFH1104 has 14mm. This spacer is placed on LFH1104.
Replacement climate control knob shaft (stem pin) designed for 2003–2006 Mitsubishi Outlander models. This component connects the front control knob to the internal HVAC mechanism, restoring proper operation of temperature and airflow…
Headlight mount for Mitsubishi Outlander 2011, install on top of the original mount
Mocowanie tylnej kamery do mitsubishi outlander 2 Wymiar kamery 24x24mm
The little tabs that holds this down broke. Just made a replacement. Printed fine layers .12mm tilted about 80 degrees sideways to maximize strength for the small snaps that holds it in place. I used PETG.
Эта модель возможно подойдет на другие схожие крепления лампы к фаре
half scanned half modeled wheel cap for can-am outlander XTP 1000 R
Landing leg side strut for Outlander model rocket. Near-1:1 scale with Estes Outlander - reduced 10% (in Cura) before printing, for better fit to 1:1 scale landing legs. I printed all 8 struts on glass, with 4 of the 8 flipped to the…
Cover for lower section of Outlander landing gear box. 1:1 scale with Estes Outlander. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Category: Hobby
A small display model of the Outlander sniper rifle from Bugie's 2026 Marathon game. Also hand painted, Im not the greatest painter.
Top tank with opening for launch lug for Outlander model rocket. 1:1 scale with Estes Outlander. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Category: Hobby
Landing gear box side panel for the Outlander model rocket. 1:1 scale with Estes Outlander. I printed all 8 of these on glass, with 4 of the 8 flipped, to achieve a smooth outer surface for all 8 side panels. Print Settings Printer Brand:…
End cap for the four BT-50 size tanks on Outlander model rocket. Printed on glass for smooth outer (end) surface. 1:1 scale with Estes Outlander. End cap fits inside Estes BT-50 body tube. BT-20 size for the eight BT-20 Outlander tanks is…
End cap for the eight BT-20 size tanks on Outlander model rocket. Printed on glass for smooth outer (end) surface. 1:1 scale with Estes Outlander. End cap fits inside Estes BT-20 body tube. BT-50 size for the four BT-50 Outlander tanks is…
Landing gear box cover for Outlander model rocket. 1:1 scale with Estes Outlander. This version has an extended opening, for additional landing gear clearance. A version with the standard opening is also available. I printed these on…
Landing gear box cover for Outlander model rocket. 1:1 scale with Estes Outlander. A cover with extended landing leg opening, for additional landing clearance, is available. I printed these on glass for a smooth outer surface. Print…
Blanking off the DC input connectors.
When your right thumb or hand gets tired, you can use left thumb alone or to assist your right. Build-able for competent DIYer who accepts the risks. Should fit all Gen 3s with handguard frame, but only tested on 1000R Limited. I printed…
I find new G3L Outlander radiator is vulnerable to take sticks inside radiator. So I wanted to make metal cover. I added dxf model for plasma cutters. Also included measurements wher to bend it to make it fit. No need new holes. It fits…
Can Am Outlander G3L work light mount Hardware 30-35mm M3 bolt to work as hinge pin. 2pcs M6 bolt to fix mount around bumper tube.
Заглушка крепления поводка передних дворников Mitsubishi Outlander 3 (рест.3). При чистке снега отвалилась. Хорошо, что углядел в снегу. Т.к. вероятность ее потерять имеет место быть, то по-быстрому ее замоделил, распечатал, примерил -…
I've created this armrest insert to aid in keeping things more organized in there. Box size is 120 x 167 mm and the brim is 128 x 171 mm. Brim size can be increased by about 6mm all around (3mm per side) if you want a snugger fit. The…
Top tank with opening for launch lug for Outlander model rocket. 1:1 scale with Estes Outlander. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Category: Hobby
Cover for lower section of Outlander landing gear box. 1:1 scale with Estes Outlander. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Category: Hobby
Landing gear box side panel for the Outlander model rocket. 1:1 scale with Estes Outlander. I printed all 8 of these on glass, with 4 of the 8 flipped, to achieve a smooth outer surface for all 8 side panels. Print Settings Printer Brand:…
Landing leg side strut for Outlander model rocket. Near-1:1 scale with Estes Outlander - reduced 10% (in Cura) before printing, for better fit to 1:1 scale landing legs. I printed all 8 struts on glass, with 4 of the 8 flipped to the…
End cap for the four BT-50 size tanks on Outlander model rocket. Printed on glass for smooth outer (end) surface. 1:1 scale with Estes Outlander. End cap fits inside Estes BT-50 body tube. BT-20 size for the eight BT-20 Outlander tanks is…
End cap for the eight BT-20 size tanks on Outlander model rocket. Printed on glass for smooth outer (end) surface. 1:1 scale with Estes Outlander. End cap fits inside Estes BT-20 body tube. BT-50 size for the four BT-50 Outlander tanks is…
Landing gear box cover for Outlander model rocket. 1:1 scale with Estes Outlander. This version has an extended opening, for additional landing gear clearance. A version with the standard opening is also available. I printed these on…
Landing gear box cover for Outlander model rocket. 1:1 scale with Estes Outlander. A cover with extended landing leg opening, for additional landing clearance, is available. I printed these on glass for a smooth outer surface. Print…
Headlight mount for Mitsubishi Outlander 2011, install on top of the original mount
Replacement climate control knob shaft (stem pin) designed for 2003–2006 Mitsubishi Outlander models. This component connects the front control knob to the internal HVAC mechanism, restoring proper operation of temperature and airflow…
Заглушка отверстия для разблокировки АКПП Mitsubishi Outlander III рест.3. У многих, в т.ч. и у меня, она была утеряна "
Заделал себе защелку подлокотника с удлиненным зацепом. Если в подлокотнике много барахла всякого лежит, он, бывает, не защелкивается. Отсканировал, сделал модель как со стандартной длиной зацепа так и с увеличенной на 10 мм. Вдруг надо…
Mocowanie tylnej kamery do mitsubishi outlander 2 Wymiar kamery 24x24mm
- Mitsubishi Outlander interior part 6977A273ZZ - Printing of ABS is preferred. - Acabamento Parafuso Trilho Banco 6977A27
Hello everyone! Really happy to present to you Claire Fraser (high-detail) at Craigh na Dun from the Outlander series. 100% ready for home printing test-printed Available in 1_9 scale This model captures Claire in her iconic pose as she…
