Counting matching models…
This thing was crowd designed by the members of the Espresso Aficianados Discord . If this design or espresso interests you, hop in and say hello! The Tool A nine pronged WDT tool. This was designed for 0.4x75mm 0.35x75mm acupuncture…
A small adapter plate to convert a quarter-turn mount to 2-pronged GoPro. There are plenty of models to convert to a 3-pronged GoPro mount, but I struggled to find one to go to the other side of the GoPro mount. Note that there are two…
A nine pronged WDT tool that's printable in a business card size. This was designed for 0.35x75mm acupuncture needles with a 30mm handle. I used https://www.aliexpress.com/item/1005001467649993.html . Dull the tips of the needles on an…
A small adapter plate to convert a quarter-turn mount to 2-pronged GoPro. There are plenty of models to convert to a 3-pronged GoPro mount, but I struggled to find one to go to the other side of the GoPro mount. This is designed to accept…
A replica of the Three-Prong Muzzle Brake designated for use with Surefire SOCOM556 suppressor replicas, but can also be used alone. The muzzle brake should be screwed onto the replica (CCW thread) so the windows are facing upwards. Use…
WARNING NOTE: This cover is NOT intended to be used as a child safety device and is purposefully easier to remove than covers made for safety purposes. This is a blanking plug that fits into and covers the standard 3-prong power outlets…
The prongs are a weak point in the Flatbox printed due to the orientation that they were printing. This version fixes that. In this version, the prongs are printed on their side and held in place by a small disk. The disk allows creates…
A handheld loom for making rubber band bracelets. Best used with a small crochet hook for looping the bands through each other. Looms of this style typically taper towards the bottom making them difficult to hold on to, so I designed this…
I purchased a replacement brush bar for my Dyson V7, only to find that the new brush bar uses a different mechanism to interface with the motor. (See photo comparing the two styles) I tried looking for the correct brush bar but as far as…
This is a bolt-on GoPro-style 3-prong camera mount designed for the Mark 4 FPV drone frame in the 5–7 inch size range. The flat base mounts directly to the frame using standard M3 bolts and provides a secure platform for action cameras…
Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_ext_th = 4 gopro_ext_len = 20.7…
Original model by darazs, posted to Thingiverse, see link. Accepts M5 bolt and nut. Print in vertical orientation (with supports under GoPro mount with slots vertical) and shouldn't require any supports within the quarter turn interface.…
A remix of aclmech's excellent WDT design to use the installation mechanism from vonbauernfeind's also excellent WDT. This one is designed to fit a specific 0.4mm x 75mm 3d printer needles that have a handle on the blunt side. I used…
Update 12/19/22: Added version for 3-prong plugs (NEMA 5-15) Update 12/19/22: Added version for plugs with a larger neutral blade (polarized plug). My new laptop travel charger cable came with a prong protector but I kept misplacing it.…
Designed to fit a standard 26mm tyre. +3mm offset, 12mm hex. Will take up to a 4mm shaft. For personal use only. No commercial sales.
Remixed from the original for more consistent print finish and personal aesthetic preferences.
I found it quite easy to bend the needles using the original stand. So, I designed a new one, hanging style. Make sure to turn up your model fan on the upper part, to avoid bad cooling. I printed with Bambu Labs P1P with some abs, but i…
The prongs on the original model were a touch too short for my bin, leading to the latch falling off. This remix extends the prongs to 7.54 mm, measured from bottom of prong fixture to top of prong. See images for how I measured the…
Not 100% accurate, will follow up with the photos of the actual prints. Print this vertically with the prongs side down (use supports, but make sure to add support blockers on the threads). There are holes on the prongs you can shove…
The same as the remix source but with two prongs removed which allows for cables with larger connectors.
This is a simple Gridfinity 1x1 unit to hold any grounded (or non-grounded, I guess) US plug. Personally, I wanted this for my Klein RT210 GFCI outlet tester but it should work for anything small. It's intentionally a little bit of a…
I was unable to find such a key for franke pescara slide-in perlator. Printed in standard PLA. Add a raft for good measure because a footprint is rather tiny and likes to detach with 0.6mm nozzle and 2 perimiters you'll get a nice, tight…
This is a component of a prototype I created (designed in Fusion 360). While my model didn't prove to be useful, I decided this individual component might be helpful to someone else. My gut reaction is that supports are absolutely…
I had a hard time fitting the cable chain base mount, maybe it's just because my variant of Elegoo Neptune 3 Pro have narrower slots or because I am printing on PLA+. So I cannot fit the cable chain base, only the two upper prongs will…
A simple adapter from 3/8ths inch Microphone stand thread to the three-prong mount system used on GoPro and similar Action camera accessories. Printed in Prusament PETG black.
Changes allow placement over plugs that did not fit through the original loop at the end of the tether. This was done as the loop did not fit over the plug for my diesel engine block heater. Hat tip to Grant for the original model used…
This contains both sides and a clip for an American style 2-prong body cord. Prong holes are enlarged to prevent minor print defects from affecting assembly. The holes are threaded and accept M3x10 and one M3x16 screws. The 16mm screw is…
These are designed to be fit to replica airsoft rifles with 14mm negative (counter clock-wise) barrel threading. There are four full length options: 40mm, 50mm, 60mm, and 70mm. All measurements are the full length of the model. The…
design notes I wanted a simple outlet cover to keep dust (and the desiccant I have now spilled twice) out of the power strip next to my desk, but I didn't find one I liked. this outlet cover is designed to: print without support print in…
Pretty simple design. The gap measurement is the distance between the prongs. If you add 32mm to that number you get the actual length end to end. Example the 15mm gap model is actually 47mm long. I widened the models that are 45mm and up…
This model is compatible with the lego system.
Inspired by and to get the GoPro 8 non-prong mount: https://www.thingiverse.com/thing:4382722 For when you don't want to risk your GoPro on your quads. Set your slicer to do a pause or filament change at the top of the empty cavities.…
*DO NOT PRINT WITH CONDUCTIVE FILAMENT* My first two versions of an MCC hanger didn't contain wire management, Third times a charm I guess. This is a minimalistic hanger for Olight magnetic charger bases. It should work with any light…
A nifty holder with standard spacing for those cheap no name banana plug you can find on ebay and various hardware shop. Plugs right into most lab bench power supplies, marked with polarity.
I cobbled this together in TinkerCAD because it is a PAIN in the butt to find a camera mount for this specific board (the 36x36 board with the screws on each corner...) so! I made this! I jacked the mount point from one of the camera…
I made this as a homework assignment a few years ago, and it was a to-scale replica of an electrical plug… thing. Not sure what the exact object was, but it might be helpful to someone!
Using a prong lets you insert and remove the attachments without rotating them 90 degrees which lets you space them as close as possible and mount them without having to align the notches. Off brand kitchen aid attachments have different…
UPDATE March 2023: There is now a v2 of this model that is attached magnetically (turns out the locking prongs in this one tend to be a bit fragile and can snap off if mistreated). ---- A funnel to help filling 58.5 mm protafilter baskets…
A cool spear that is double pronged. Good for displays, collections and just stabbing things.
Protectors/covers for type A (2-prong) and type B (3-prong) plugs. Tested with PLA and 0.8mm nozzle. But should work with smaller nozzles and PETG too. Use random seam alignment. Don't use silk or matte PLA because it has poor layer…
The dual prong and trident handheld display stands were inspired by a model posted by Snoopy31195 . They are designed to print quick while being esthetically pleasing and keeping filament usage to a minimum while maintaining stability. I…
More flimsy than I would like. for best results use a smaller nozzle and high density infill
There are a variety of different sizes provided. The measurement provided gives the width of the space between the two arms; all are exactly 28mm wide on their outer edges. The hooks are mounted via a single multiconnect peg. These pegs…
Modified magnetic clip for 9 Prong WDT Espresso Tool that uses 8x3 magnets instead 5x2 magnets used in original design.
Pronged stud die for KAM snap pliers. I included one file for genuine and one for the knockoff tool. The latter has a bit narrower shaft in my experience. Works with those snaps: https://www.adventurexpert.com/product/two-sided-kam-snap/…
Four pronged version of a handle for the wing nuts on a harbor freight paint pressure pot I use for resin casting. Allows a better grip to tighten the lid better to prevent leaks. I made the cutout tight enough so it will slide onto the…
My workspace was full with an army of battery chargers and other power bricks… You know the ones, the bulky "brick" style chargers with the electric prongs sticking straight out of the back. They don’t sit flat on a shelf, they tangle up…
My own custom design of a NATO interface, prett small triple prong flash hider that I modeled mostly to practice CAD skills but it does look pretty cool, works well with a slightly futuristic look. Not tested! 14mmCCW thread STL + STEP…
My wife lost the heel from one of her favorite boots so i made this. Printed in PLA and glued a rubber pad i cut from a rubber gasket. As it is a rather rare type of heel, i've posted this, maybe someone else needs it. If you like my work…
This stand is designed so a bottomless portafilter will rest flat easily on it (with the handle resting on the countertop or table), and have access to a WDT, leveller, and tamp close-by. The WDT ‘holster’ is for the design by jkim_makes…
Vidle jsou vytvořeny podle historické předlohy, která se zachovala až do dnešní doby a je stále vyráběna. Ve hře Kenka puppetgame jsou součástí edukačních historických nástrojů, ale velmi dobře slouží i v bojovém nasazení. Výroba vidlí s…
I remixed the 3 prong version to be used with a 51mm 2 prong portafilter, specifically the delonghi ones. The fit is pretty snug but i find I prefer that as it prevents it from slipping off when you don't have magnets, or if you do have…
Probably my most dangerous, but most useful, model to date. I printed a few of these, because I have quite a lot of EU plugs, but only crappy adapters. This “Portable Earth" prong allows the UK sockets flap doors to be opened, and the EU…
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/82dEubKirxX Looked at loads of these but they looked a little complex so I made one. I bought the cheapest 0.4 nozzle cleaners I could find on ebay:…
Remix for use with my https://github.com/prusa3d/Prusa-Firmware-ESP32-Cam I use with https://www.printables.com/fr/model/164263-remix-of-action-camera-mount-for-mini/comments on my Prusa Mini
I recently got me a Caddx Walnut, and needed a mount, and there don't seem to be that many out there, so I made my own. Attribution: I took the GoPro prongs from MrSwarets Session 5 Mount (can't link remix source for some reason, so use…
I had to reverse engineer the knob because solidworks didnt want to work with me
Attakt is a 3D‑printed floating handle designed for action cameras that use the standard GoPro 3‑prong mount . It features a secure ergonomic grip, a high‑visibility base, and a precisely modeled mounting interface for reliable attachment…
A simple claw that can be used for just about anything. Needs: 2x spider 4x arm 4x link M4 screws and nuts (to connect everything) Working to help the spiders align better.
I took the side bin from the fellow opus for the clip on holder. The clip on holder fits on the top right side or the left side, as you wish. Enjoy your day with good coffee.
Tired of the plastic body of my LP sockets cracking. Usually breaks at the insulated-prong-side nut- probably my fault for over-tightening. Good thing I can print a new one! Added a bit of thickness all around (compared to the original),…
Needed something to protect my cords in my woodshop as I'm bad about unplugging one tool and letting it's cord lay in the floor, then manage to step on it and bend the prongs :( This should prevent that. Added a tail to afix it to the…
This is a remix of RxMiller's SmartiPi Toolless Mount . I liked the mount but needed one that was horizontally oriented. But then realized for heavier objects needed more supports on the top and bottom. So remixed a few versions, one for…
I was using this lampholder / lightbulb lamp with tape over the screws / terminals for the longest time which isn't very safe so I decided to make something nicer. It just screws in with the normal screw holes and I made a knot inside…
Hello everyone. This is my first Printables 3D model and its nothing fancy but first thing I designed that I think would be universally useful to other people. I lost that metal fastener which clips the metal prongs that go through the…
This is a custom-designed holder for the Niimbot D110 label printer, made specifically for the IKEA Skadis pegboard system. It solves the common issue of loose pegboard accessories by using a reinforced mounting design. Features Solid…
Captain Slug's design. I needed a slightly longer Rivalburn prong for the inline version for my build. I cut the prong in 2 then extended the part that hits the elevator by about 50 mm. Then I joined the pieces back together. Used…
Replacement prong for buckle Casio G Shock GA 2000 . Printed with PETG, 100 percent infill
Use it with any of the original quadlock mounts (e.g. magsafe or charging heads) or print a basic one yourself. Supports needed. Printed with 0.10mm Layer Height, GoPro prongs pointing up. Pause at 9mm to add a M5 hex nut. 1/4 inch to…
This is a meme i felt like it
This is all the parts/guide Guide: https://docs.google.com/document/d/13WKLTKDnHHxhQVdz6h26Yhp7TMm8doU4Xy8oVETHfDQ/edit?tab=t.0 Board: https://www.amazon.com/dp/B07MLXS877?ref=ppx_yo2ov_dt_b_fed_asin_title Wires:…
3d printable eyeball to stick into things
I ran out of fasteners for my binder and couldn't find any models for it so I made my own.
I just chopped off the mount and added the GoPro prongs to the model. This allows you to mount it on an adjustable base which I like on my long-range quads. Print Settings Supports: Yes Infill: 100% Filament: Sainsmart TPU Blue Notes:…
Background The M4 rail wallet is the latest small form factor card carrier style wallet from Dango. It manages to have a remarkably slim profile, while still being able to hold a decent number of cards as well as some cash. Unlike the…
Disclaimer. this only works on belt drives and not the shaft drives. Recommended material (PETG, PET, ABS, ASA) Recommended settings (infill 10-15%) (walls 3-4) extra hardware (gopro thumb screw, M5 nut, and a gopro cam)
I needed a way to mount the clamp from the Modular Mounting System ( https://www.thingiverse.com/thing:2194278 ) ((Note I imported this from my Thingiverse but haven't updated yet based on if that system is on Printables etc)) to both…
Achilles Fork A tendon is not a muscle and there is no pressure dose for it. So this is a fork: two rails straddle the Achilles and load the muscle-tendon junction either side, with a clear channel down the middle. TARGET AREA:…
Clean under the keys or swap to a new set: slide the two prongs down opposite sides of a keycap until the hooks catch under its edge, then pull straight up. Plastic prongs won't scratch the caps the way metal pullers can. DETAILS • Two…
Push the prongs into an onion, tomato, lemon, potato or cucumber and slice evenly right down to the end, with your fingers safely on the grip and away from the blade. The knife slides between the prongs for even slices, and your fingers…
Modeled this to replace an outdoor lighting stake that broke for a 12-Volt outdoor fixture. I modeled this for someone else, I myself never printed the model but I heard it worked. It is not meant to be an exact replica but rather a good…
Hello everyone. This is my first Printables 3D model and its nothing fancy but first thing I designed that I think would be universally useful to other people. I lost that metal fastener which clips the metal prongs that go through the…
Use it with any of the original quadlock mounts (e.g. magsafe or charging heads) or print a basic one yourself. Supports needed. Printed with 0.10mm Layer Height, GoPro prongs pointing up. Pause at 9mm to add a M5 hex nut. 1/4 inch to…
This model is compatible with the lego system.
Printed out the Extraplanetary Geared Stand, but found the little prongs that the phone sits on were too narrow. https://www.printables.com/model/1278870-extraplanetary-geared-stand I've made a little exetension piece which is longer and…
Disclaimer. this only works on belt drives and not the shaft drives. Recommended material (PETG, PET, ABS, ASA) Recommended settings (infill 10-15%) (walls 3-4) extra hardware (gopro thumb screw, M5 nut, and a gopro cam)
I ran out of fasteners for my binder and couldn't find any models for it so I made my own.
This model is compatible with the lego system.
A prototype 4 prong rake used for level espresso beds, not for deep WDT. Designed to move the grinds around. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .15 Infill: 15 Filament: hatchbox pla…
____________________THIS IS A DIGITAL PRODUCT, STL FILES FOR 3D PRINTING_________________________________________NON-REFUNDABLE_______________________ Files to print Fantasy Tiefling Stocky Prongs Horns Set from Baldurs Gate 3 The…
Pretty simple design. I might remix later with holes in the bars to help save material. The gap measurement is the distance between the prongs. If you add 32mm to that number you get the actual length end to end. Example the 15mm gap…
Pretty simple design. I might remix later with holes in the bars to help save material. The gap measurement is the distance between the prongs. If you add 32mm to that number you get the actual length end to end. Example the 15mm gap…
Printed out the Extraplanetary Geared Stand, but found the little prongs that the phone sits on were too narrow. https://www.printables.com/model/1278870-extraplanetary-geared-stand I've made a little exetension piece which is longer and…
This is a robust, high-strength adapter designed to mount your action camera (like Insta360 Ace Pro, GoPro, etc.) onto any standard 1/4" tripod screw. By using Carbon Fiber (CF) filament and embedded hardware, this mount offers superior…
