Counting matching models…
I've been using these printed in PETG for the better part of a year without issue. Replacing the altitude lever-knob This is a drop in replacement. Start by removing the original lever and spring by unscrewing the internal screw. The…
Modeled after original best to print in PETG for that flex much easier to install i printed it on side with brim supports needed.
Remixed from @derekyle_481832. These are feet that attach to the bottom of the keychron Q6 max (and maybe other models) to give it a bit of lift. I really liked the original but it was too steep for MOA keycaps. Requires 4 M3x25mm socket…
This is an IO shield for an Intel DQ67OW Micro ATX motherboard. Tested in PLA, printed at a 0.2mm layer height with 20% grid infill. It is working with no issues. If this model is useful to you, consider checking out my YouTube channel (…
see the update at the end. Supports for the EQ6 R pro . Tested on soft ground (sand ground and grass), ceramic floor with relief and sandstone floor, improving stability, accidental slippage and preserving the ceramic floor. Optionally,…
I added an OLED module to my Keychron Q6. Since it is using QMK, it is easy to customize it. I added a guide as a PDF that should have all the necessary information to build one yourself.
IO panel for StoneStorm Q670 to mount with https://www.printables.com/model/675512-mini-itx
The Keychron Q6 does not have integrated feets to angle the keyboard. This model solves it. Print 2 of it, one for each side. The angle is 6.4 degree, meaning the back is raised about 1 cm. This model was inspired by this model:…
Print it with 0.15mm layer hight and black matte PLA. The notch simplifies installation. This makes it easy to screw in. Use at your own risk.
Remixed my Model to fit the Power Supply of the Pegasus Advance, since it has bigger dimensions due to user request
The IO Panel which is delivered (at least on my board) is just a tottaly wrong one which is not fitting. Not even a little. So I made my own. Just place it flat on the build surface for printing. No support. Printed mine in ABS.
The screw on my clutch lever broke when trying to remove, "thanks" to threadlocker. I couldn't successfully drill out the remainder of the screw embedded in the clutch, so I replaced the clutch lever with a press-fit version instead.…
Bracket Assembly for License Plate Installation This bracket assembly allows for installing a license plate on the lower part of a bumper without drilling any holes. I scanned the bumper of the car and designed a custom-fit part around…
Remixed to fit the larger 2" / 50mm tripod legs Category: Physics & Astronomy
Malolo has created a really nice customasable case for the Raspberry Pi. I needed a mount for my Sky Watcher EQ6-R tripod so I could mount a Raspberry loaded with AstroBerry on it. I used the extra high version of the Malolo ( Malolo's…
Modeled after original best to print in PETG for that flex much easier to install i printed it on side with brim supports needed.
Best Printed with TPU. PETG/PLA also possible. Quite a tight fit. You can scale the model if needed.
Um die Bohnenmenge meiner Siemens EQ6 S100 Kaffeemaschine zu erweitern und eine ganze KaffeePackung von 1 KG auf einmal einfüllen zu können habe ich diese Erweiterung gezeichnet. sie passt über die Original Bohnenaufnahme und wird mit dem…
vylepšení nastavení výšky montáže eq6 pro. zakoupil jsem použitou montáž a byl problém s nastavováním výšky a utažením v potřebném úhlu. zkrátka šroub klouzal po segmentu a ohýbal se . po této úpravě již s nastavením nemám problém jelikož…
I created this bracket to fix a Omegon dew controllerbox to the tripod of a Sky Watcher EQ6-R equatorial mount.
I bought a new Audi Q6 e-tron but the trunk/boot didn't had any hooks for nets on the sides above the wheel arches. So to ensure small items tucked in the side tray don't roll around in the trunk/boot. Slide them in and they wont move.…
In order to polar align your mount during daylight or even between two sessions, you have to take markers during night time to place your mount in the same exact position. This can be greatly simplified using a line or cross laser…
This side cover for the Skywatcher EQ6-R has mounting points for a FYSETC E4 used as an Onstep controller. On the top side, there is a mounting point for an XL4015-based DC-DC converter to provide 8.3 V for Canon dummy batteries. This…
EN Handle for Siemens EQ6 Coffee Machine Water Tank The brief and basis for this project was a "handle" with one end broken off. I measured and considered how to design a model that has "no flat surfaces" – it's a truly complex shape. By…
Replacement flash filter for the Instax SQ6 camera. Lost your flash filters? Never fear a replacement is here. Want to make other color your limited only by you filaments or sharpies. Three files included. Different thicknesses so you can…
Many VAG cars from (VW, Skoda, Seat) have a bump stop to keep the rear hatch firm without creating rattling noises while driving. With my Polo V, I was wondering where the noise was coming from until I saw that on one side the rubber was…
The Firefly mount for the Cineroc Tribute shell. The shell isn't pretty but is solid and very functional giving you video resolutions of 4K 24fps, 2.5K 30fps, 1080P 60fps/30fps, 720P 120fps, VGA 30fps, when using the Q6 Firefly. I print…
For me it was the option to optimize the filling of the beans. But it’s also an extender. Print it with organic supports.
Protects the extension rod especially during transport. Printed from flexible TPU material.
These custom riser feet are designed for the Samsung HW-Q600C soundbar. They raise the soundbar by 2 cm, providing better support and allowing for improved airflow or cable clearance underneath. The design is simple, functional, and easy…
https://www.best-power.cz/bateriove-generatory-230v/bateriovy-generator-viking-vali150/ HEQ5: https://www.printables.com/model/1187519-heq5-powerbank-viking-vali150
This is a Compaq Presario CQ60 (maybe other models too) hard drive cover. I purchased this laptop for cheap, but it was missing the hard drive cover. Without knowing what the original looks like, I designed this cover. So far, it's worked…
This model is a replacement for the cover of the emergency key for the Ioniq 6. It prints well when positioned upright,with the small hole facing down.
This is a short stand to be used in place of the supplied stands so that the TV sits as low as possible on a desk. I use this TV as a monitor and need it to fit on a desk under a shelf. This leg provides the shortest height possible. Can…
Stylish inspired keychain designed in the shape of a car front. Perfect for car enthusiasts, this keychain keeps your keys organized while adding a touch of automotive style. A great accessory for everyday use or as a small gift for…
Snap on Lid and Base 3mm mounting holes a lid, base, and a button up to 50mm fan mount Use a piece of filament for the button hinge. Version 2: widened by 2mm for easier fit, added a little extra thickness to larger IO cutouts. Have a Q6A…
Remixed from @derekyle_481832. These are feet that attach to the bottom of the keychron Q6 max (and maybe other models) to give it a bit of lift. I really liked the original but it was too steep for MOA keycaps. Requires 4 M3x25mm socket…
This is an IO shield for an Intel DQ67OW Micro ATX motherboard. Tested in PLA, printed at a 0.2mm layer height with 20% grid infill. It is working with no issues. If this model is useful to you, consider checking out my YouTube channel (…
Replacement battery cover for a Instax sq6 camera. Model isn't perfect but it does hold batteries in place. Everyone is welcome to modify it, just post a make or remix if you do so it'll work better for the next person.
Fuji SQ6 replacement flash cover. If your flash cover has gotten broken off this is an easy replacement. meant to be printed in clear and superglued in place. Easy to print but if you want to buy 3 they are available at……
I printed it with 0.2, 40% infill, brim and supports and worked well with PLA. Have not tried other settings. This is an original model, inspired by brackets for similar other Beelink models with different dimensions.
I came across this on Tinkercad, but it contained quite a few errors in the model, misaligned bits etc. So I cleaned it up and made it more printable and now it lays flat on the print bed, the slats are properly meshed with the crate body…
I really liked both designs I remixed from, but I saw a bit of an idea to try. These WPL and JJRC trucks are pretty darn light weight. Which, in theory, could be bad for traction. And in some models they're a bit top heavy and can easily…
After upgrading the ESC in my WPL and JJRC trucks I found that I could no longer easily reach the switch to turn them on or off. The ESC is a fairly common inexpensive brushed with or without brake model. The switch drops right in place…
EQ Direct (EQMod) module for SkyWatcher EQ6 Pro mount Wiring diagram and PCB Gerber files is included BOM 1x CH340G chip 1x 12.000Hhz crystal 2x 3mm red LED 2x 4k7 axial 0.25W rezistor 2x 22pF ceramic capacitor 2x 100nF ceramic capacitor…
I needed something to hold my RPi 5 on the mount. I used the hole that was previously used for PA and PoleMaster. This is specific to the RPi5 with the red & white curved top case. Add a couple M4 grub screws to attach to the mount.
To separate water from used coffee ground for Siemens EQ6 coffee machine. This grating avoids used coffee ground to end up as a soggy waste in the bottom of the container. Printed with PETG, 15% infill.
ISDT Q6 Plus and ISDT PC-4860 1-8S Safe Parallel Board XT60 Parallel Charging Board Storage Box. Ideal charger for charging your RC batteries in the field and should fit in your FPV backpack. Storage Box should fit the charger snug and…
Auxiliary tray for the SkyWatcher EQ6 R pro mount. See: https://www.printables.com/es/model/304688-new-tray-for-the-skywatcher-eq6-r-pro-mount In case it can be useful, I leave you this tray, adapted to the tripod of the EQ6R pro. It is…
The rear elevation adjustment bolt on the Sky-Watcher EQ6R-Pro mount has a spring loaded handle that can be difficult to use for fine adjustments while doing the polar-alignment (PA). It tends to slip and not grab all the time. While…
New version of the tray for the Skywatcher EQ6 R Pro mount, more rigid and with grooves. This tray can be mounted on any mount with a 2" diameter tube and an angle of 56°, to maintain horizontality. To prevent rotation on the polished…
see the update at the end. Supports for the EQ6 R pro . Tested on soft ground (sand ground and grass), ceramic floor with relief and sandstone floor, improving stability, accidental slippage and preserving the ceramic floor. Optionally,…
Attaching the IP camera to the CNC 3018 machine table Applicability: CNC 3018 Pro ESCAM Q6 Assembly components: M4 screws M4 nuts Category: 3D Printer Parts
I created this bracket to fix a ZWO 12V 5A power adapterto the tripod of a Sky Watcher EQ6-R equatorial mount. Like it? Buy me a coffee: https://buymeacoffee.com/erwinha
My Wedge Stand W1 design tailored for the InWin BQ656 (BQ Series) computer case. Its crescent shape carve-outs follow the mesh panel corner and open up the PSU intake area. Bottom clearance height set at 7mm for proper PSU airflow. Suits…
A simple stand for the Korg SQ-64. The cool little sequencer that is now cheap cheap cheap. Mirror it over and make a pair. Snap fit. I included a little hook to allow bundling of cords as they travel along the rear. Maybe twist tie them…
Der Griff des Wassertank meiner Kaffeemaschine brach und keine Ersatzteil war in Sicht. Für mich der Grund endlich in CAD und 3D Printing einzusteigen. Letztendlich konnte ich das Modell nachbauen, ohne das Design, rein funktional und mit…
This is a conversion of Orion Atlas to Onstep. It should also fit EQ6 class mounts. It is using FYSETC E4 running OnStepX
[Update 15-5-2019] I bought some lights for this truck and updated my files to allow for easy instalation/wire management. I redesigned the "Spacer" and the "Servo Tray", which now has 2 versions, for a 9g or a 55g servo; with the 9g one,…
Simple covers for the EQ6 pro. Print with supports touching buildplate.
When using the EQ6R Pro mount in a fully automated setup, there is a risk the cables get caught on one of the handles. This is a big problem with fully automated setups, that run unattended through a whole night (possiblity with a…
Permet de maintenir une perche universelle plus large que celle d'origine
The stock wall mounts that came in the Samsung package made the unit sag down (yes, it was in a wall stud). So I made a custom mount that also has a couple Wii Sensor Bar slots to help free up my entertainment center. (Stud finding is…
A Case for ISDT Q6 Nano with USB-C Power! -8 round magnets 6x3mm embedded in "top" and "clip", you have to pause the print to put them in! -Solder XT60 so PD board and glue PD board in the case -Put Charger in the bot part and push the…
EDIT: I will upload photos once it's printed, and will likely have updates ________________________________________________________________________________________________________________ Calling all my ANSI Sisters and Brothers who have…
I added an OLED module to my Keychron Q6. Since it is using QMK, it is easy to customize it. I added a guide as a PDF that should have all the necessary information to build one yourself.
Print two of these. The holes on the top let the built in feet recess and hold the keyboard steadily in the stand. The model marked Rubber has a 1mm inset to put in up to 10mm rubber feet if you don't want it to slide. I printed with…
Created with Siemens NX 12 Printed with Creality Ender 3 in PLA Print time with 0,4mm Nozzle: ~3h PS: It works, but the model fits not perfectly! It was designed rather quick and dirty ;-)
Pier adapter for my EQ6 mount, 3D print possible, but for more robustness, I made it on CNC in aluminium.
This adapter goes in place of the factory supplied stand/feet for the TV. In my case I wanted to mount the soundbar under the TV and the hardware I had wasn't optimal. Remove the feet and bolt on these adapters. There are M8 mounting…
Leveling ring for your EQ6R Pro, because the built-in level is worthless (at least mine is). You can connect the mount to the tripod with the ring in place, and if you move or bump your mount, you can re-level without removing the mount…
If you get into astrophotography with a mirrorless or DSLR, the next advised upgrade is a tracking mount. If you know you're going to be in it for a while, the EQ6R Pro is a very reliable option. But while you're saving for an OTA, and…
A strap mountable clip for the flash filters that come with a FujiFilm Instax SQ6 so you don't have to carry them in your pocket. I made this thing with Tinkercad and a fair bit of trial and error (one of my first 3d models!):…
A little adapter to attach those little phone fisheye, macro, etc. lenses. They use an M17x1 thread. Clips firmly onto the front lens extension. Designed for the Instax SQ6 but I reckon it may fit the others as the mechanism looks…
Split the exposure area when using the double-exposure mode for some fun effects. Clips firmly onto the front lens extension and spins freely when needed. Designed for the Instax SQ6 but I reckon it may fit the others as the mechanism…
This is a larger round flash diffuser for an Instax SQ6. Reduces the flashes power but makes it softer. The bottom of the diffuser is 0.3mm thick so if your printing at 0.2 mm layers make that next to the bottom layer 0.1 with variable…
This is a modification of the original Firefly Q6 Hat Clip by btnewman. It is modified to tilt the camera up 10 degrees via the bottom part that attaches to the hat so that the angle of the camera is angled up higher to be more level for…
it's only the inner rotule, changed to support a 3/8 x 16 screw, to convert these wonderful LARGE AND STEADY feet for tripod use. https://www.printables.com/model/309201-supports-for-skywatcher-eq6-r-pro-mount all the glory goes to the…
Got tired of carefully storing my freshly taken instax photos in my pocket. Made an attachable case that stores 10 photos. Slides snugly into place It completely blocks the mode button, but flash and timer buttons are accessible. Can be…
Vidroc Firefly Q6 This mount allows you to easily mount a Hawkeye Firefly Q6 to your rocket. You can optionally screw the mount onto your airframe but otherwise you can use a nylon strap or steel hose clamp to quickly mount it to a rocket…
This is just a basic model that fits the angles of the keyboard and can attach with 30mm long m3 screws in place of the 4 short m3 screws that run along the top of the back of the keyboard. You could adjust the depth of the screw hole if…
This is a cover for Lantian 24V power supply that is used often with lipo chargers like: ToolkitRC M6 ToolkitRC M8 ISDT Q6 You can buy this power supply here LANTIAN 24V POWER SUPPLY This simple cover protects from electric shock. It was…
Remix of the q6 nano holder for Ikea Skadis by Leif3D on Makerworld. Replaced the skadis hooks with a multiboard push fit. Printed in white PLA, 0.2mm layer height, 15% infill and 3 walls. Rubber mallet helps getting it installed ;) Remix…
Hi! I made this to attach to my tripod legs, to stop me kicking them accidentally. Requires 6x M4 threated inserts and 6x M4 countersunk screws. Printed in Copymaster 3D Glow PLA Filament Layer:0.2mm Infill: 20%
For the threads for the m12 bolt probably want a layer height around 0.1 get enough detail. The hook gap (width) is around 50mm Printed on Bambu lab p1s
Hi! I made this to mount a PSU to the handle of my EQ6-R, inspired by something I saw on facebook, made for this PSU: https://amzn.eu/d/dVOVotL I used this model for handle geometry: https://www.thingiverse.com/thing:5414767 Printed in…
This tool allow the adjustment of the split nuts on the NEQ6/EQ6 easily. You need two jewellers screwdrivers with 3.5mm wide blades. Stick them in the holes, line them up with the nut, and torque using another screwdriver. No pressure is…
