Counting matching models…
This is a CR-Touch mount to be used on the Sprite Extruder variant that comes with the Creality Sermoon V1. It may fit other variants of the Sprite Extruder too. Offsets: X: 34mm (or -34mm, depending on firmware and extruder orientation)…
With some additional soundproofing applied on the side panel / door gaps this cover resulted in a 20% (9 dB) overall noise reduction in addition to the improved ABS print quality. It also improves air purification efficiency if you use a…
This model avoids the interference or collision of the ABL sensor with the other parts of the 3D printer. There are 2 models: (1) the bracket and (2) a model of the BLTouch itself for hand movement testing. Four M3 hex head screws are…
Wanted to not have to take my bltouch off to take resonance measurements on my Sermoon D1 with Sonic Pad for Klipper. Let me know if you have any trouble but mine seems to be working well but made a few adjustments based on that. 11/6/22,…
This is a drag chain for the sermoon d1 that I came up with. The links are a remix from https://www.thingiverse.com/thing:611593 and the springs are from https://www.thingiverse.com/thing:4651710 I made this to be mounted on the filament…
This model is assembled from five parts. You will need the following hardware: 2 pcs M4x20 Allen screws with nuts (for the fan assembly.) 2 pcs M2x12 Allen screws with nuts (for the fan duct and outlet manifold assembly.) The fan duct and…
Print the parts with thick walls and top/bottom layers (2.4 mm.) Use 40% infill. It needs to be strong. In addition you will need: 2x 688ZZ (or 688-2RS) ball bearings (8x16x5 mm) 4x M4x10 Allen Head screws with washers 4x M4 T-nuts 4x…
Also look at my other accessories for the Sermoon S1! Description: This insert allows more efficient storage of all your accessories in the original case of the Sermoon S1. Insert accommodates: Scanner (including my lens protectors:…
EN: This is a Creality Sermoon S1 scan of an Egyptian souvenir of the falcon god Horus. The scan was created with 0.1 mm resolution and blue cross, parallel and single lasers. Unfortunately, even the original has poor resolution, as is…
Allows you to not have to take the CR Touch off to take resonance measurements for Sermoon D1 with Sonic Pad for Klipper. This is a remix of the below two designs. sermoon d1 adxl 345 mount by PA3MA - Thingiverse Sermoon D1 CR-Touch mount…
Simple but nice TFT35 E3 Mount for the Creality Sermoon D1. It is plug and play, you can use the Original Micro USB Cable too. Happy Printing!
This uses the original screws, no new hardware needed, photos should be in order (graveyard of test fits and designs that got aborted). I'M NOT USING THE ORIGINAL THROAT, MIGHT BE DIFFRENT DEMENTIONS. I'm using the Creality Titanium…
Sermoon D1 filament guide. I was having an issue where the original bearing guide was binding up when the print was in the far corners of the build plate, and had the filament break at the extruder due to the stress. Uses existing screws…
Similar to my other scaners I like some additional protection for the lenses that don't obstruct the scanning capabilities so they can stay attached to the scanner. For this I just scanned the Sermoon P1 and did a quick model in…
Two M3x8 and two M3x4 Allen screws are required to install it. The two M3x4 screws holding the BLTouch self-tap into the bracket (do not overtighten!) Two M2x6 Allen screws are need to attach the cable clip (do not overtighten!) I used…
I recommend using filament that is heat resistant. Infill 20% or more. No supports.
Copy of original ziptie holder on Creality Sermoon D1. Category: 3D Printing
Synchronizer Pulley Print with at least 2 mm walls, top/bottom layers and at least 40 % infill. This part needs to be strong. in addition you will need the following: Two GT2 36 teeth pulleys with 5 mm bores. One closed-loop GT2-852 mm…
PLEASE USE THE 3-OUTLET VERSION. IT IS BETTER. This model is assembled from four parts. You will need the following hardware: 2 pcs M4x20 Allen screws with nuts (for the fan assembly.) 2 pcs M2x12 Allen screws with nuts (for the fan duct…
Sermoon D1 has a underperforming extruder , in order to remove the under extrusion , i have upgraded the direct drive extruder by one from BigTreeTech , replace the stock motor with Nema 17 Pancake Motor and build a spacer that adding…
The part cooling assembly was made lighter. The center cooling duct was changed to pass more air flow. Print the outlet ducts in ASA or ABS. Note: the K1 hot end ducts are 2 mm longer (towards the bed) than the stock hot end ducts This…
My scan of the Sermoon S1 used for design: https://www.printables.com/model/1385022-creality-sermoon-s1-3d-scan-xyz-aligned Also look at my other useful accessories for the Sermoon S1 The lens protector is designed to add a protective rim…
Aligned to xyz. Scanned with the Revopoint MetroX
EN: This is a Creality Sermoon S1 scan of a Laotian Buddha souvenir. The scan was created with 0.1 mm resolution and blue cross, parallel and single lasers. Unfortunately, the quality of the original is quite rough. — I would be very…
This is a remix of Langi70's balanced cooling duct for the Creality Sermoon D1, adapting it to use with a higher output 5015 fan. (original thing at https://www.thingiverse.com/thing:5162865 ) It does help to even out and improve cooling,…
EN: This is a Creality Sermoon S1 scan of a typical industrially baked bread roll from a supermarket in Germany. The scan was created with 0.2 mm resolution and blue cross, parallel and single lasers. I also did an infrared scan, but the…
Scan of the Sermoon P1 so you can design accessoiries. Scanned with the Einscan Rigil in 3 single scans (laser mode) with scan spray applied to the transparent parts (display and lenses).
When buying a Creality Bridge, the original quick release connector is made for Raptor series scanner. So I designed one that matches better the shape of the Sermoon S1 scanner while allowing to reuse the original screw. Mine has been…
Printed in PC @6mm/s, 100c bed temp 1st layer and 108c every other layer, very large brim (stock glass bed), >4mm/s 75-100% overhang speed Supports are Tree(auto) and 27 degree threshold Should use M3 washers to prevent crushing the…
If you want to replace the dated Creality Touchscreen on the Sermoon D1, and also replace the firmware with something that actually works, then this mod is for you. The original screen has been replaced with BigTreeTech TFT5 v2.1, and the…
Covers for hole on side plate of Cerality Sermoon D1. Category: 3D Printing
I modified the original design so that the 4 pcs. in the machine. it can be fixed with a screw, or I combined the two parts.. Required parts: GT2-6mm T20 splined wheel 8mm hole/3 pcs. GT2-6mm inside 852mm/1pc. 688ZZ ball bearing/1pc.…
This is two brackets for Creality Sermoon D1 to snap on frame and black grid . Brackets are made for a drag chain "Veekaft mini 10x20 mm" . Use 27 links of the chain, beside the two end links. Seperate 3 links from both ends and cut the…
Designed for a Nidec UltraFlo 8025 fan since it has only 0.05A consumption. But should fit any 8025 fans - if the bolt holes don't line up perfectly you can just use double sided adhesive tape on the inside of the mount, it's more than…
I upgraded my Sermoon D1 to PEI and find the Super Pinda to be the best probe for bed leveling, so I constructed this adapter. 6 M3x10 screws and 4x HEX Nut M3 are required. Printing without support is at least in PETG. The X offset is…
3D-scan used for modeling: https://www.printables.com/model/1385022-creality-sermoon-s1-3d-scan-xyz-aligned Also look at my other designs for the Sermoon S1. I created this shim since the stock mounting plate doesn't fit well to the…
Display hole cover for Creality Sermoon D1
EN: These are two 3D laser scans of a Panasonic ES-LV67 shaver using the Creality Sermoon S1 and Shining 3D Einstar Rockit 3D scanners. The scan on the left (green) is from the Sermoon S1 and the one on the right (orange) is from the…
In one print I managed to damage the original cooling channel for the print. That's why I made this replacement.
Parts: Top filament guide Filament sensor holder Filament sensor holder cover JST connector cover 2x M2x8 mm screws
if you don't need the adjust function, just print the back part is enough.
This handle makes moving the cover of the Sermoon V1/V1 Pro more convenient and reduces smudges. Some minimal supports needed (see picture). Infill 20% or more.
EN: This is a Creality Sermoon S1 scan of a chestnut. The scan was created with a resolution of 0.2 mm and blue cross, parallel and single lasers. I also did an infrared scan. — I would be very happy if you have as much fun with the…
Required parts: 2 * GT2-6mm T20 splined wheel Bore Diameter: 8mm 1 * GT2 Belt Closed Loop Timing Belt 2GT 6mm 852mm 6* M4 10R screw 1 * Synchronous Belt Stretch Straighten Tensioner 2020 Profile
EN: These are two 3D laser scans of a carved East African candle holder, made with the Creality Sermoon S1 and Shining 3D Einstar Rockit 3D scanners. Both were scanned with 0.1 mm resolution and standard settings. Both scans have 1…
The P1 arrives with a spare battery to quickly continue scanning after the first one dies. In its original case it has quite a nice and protected place but I like to toss the P1 in other cases or bags so the battery has to go with it.…
Print in ABS or PC
I found a better solution for the filmanet guide for the Creality Sermoon D1. You will need a 608 bearing for this solution to work as expected. Print Settings Printer Brand: Creality Rafts: No Supports: No Resolution: 0.2 Infill: 20%…
Print in ABS or PC to prevent warping from heat You probably will want to sand down where the BL Touch mounts onto to ensure it's straight And also probably also have to bend the pin on the limit switch
Helps with tube management. Pairs up nicely with my runout sensor mount. I printed it flat in PLA and mounted it on with the stock screws. The small hole version works fine with no grommet and the large hole one fits a 5/8 grommet which…
This is a cover for the screen on the sermoon d1. I orginaly uploaded this on Thingiverse but now im starting here at printables so i thought i might just reupload. This covers the hole screen and blocks any light. The filament i printed…
Nejnižší synchronizace osy Z, řemenice jsou zkrácené, do pružných spojek je třeba vložit kuličku 7mm.
This is a variation on “Creality Sermoon-D1 Z-Axis Floating Synchronizing Idler Pulley” by shadowf@x (Thank you shadowf@x for your original idea and inspiration!) that uses 3d printed pulleys instead of ordering metal ones. You should go…
EN: This is a Creality Sermoon S1 laser scan of a Braeburn apple from New Zealand. The apple was scanned with standard settings at a resolution of 0.2 mm using cross, parallel and single lasers. — I would be very happy if you have as much…
Box for SKR 3 for sermoon D1 printer, box height 40mm, two side openings for fans 2510.
The printer didn't come with a lid, so why leave all those other covers and doors on it? It sure is a lot easier to get to stuff, and it seems to enjoy the fresh air to be honest. Printed in generic PLA with standard settings, upright, no…
Print in any high temp filament you like, i used ASA (260c and no cooling) for the initial design prints and it's been perfect 4x M3 Heat Inserts, two for the extruder mount holes and two for the old extruder motor mount holes. Insert…
Kratší držák pakebláže od bedu, ten na Thing. je pro mě moc dlouhý a kabely se v nižších polohách moc kroutí.
Výměna displeje u Sermoon d1 na BBT TFT PI 50 V2.1 pro klipperscreen
Nozzle was always dirty so I made a nozzle wiper. It takes a Bambu lab A1 mini wiper pad, A M4 screw, M4 T nut, and optionally washers to adjust the height. Comment if the height needs to be adjusted as my Sermoon D1 uses silicone spacers…
C7-5020L-07 https://www.marutsu.co.jp/pc/i/2330453/
EN: These are two 3D laser scans of a Panasonic ES-LV67 shaver using the Creality Sermoon S1 and Shining 3D Einstar Rockit 3D scanners. The scan on the left (green) is from the Sermoon S1 and the one on the right (orange) is from the…
Scan of the Sermoon P1 so you can design accessoiries. Scanned with the Einscan Rigil in 3 single scans (laser mode) with scan spray applied to the transparent parts (display and lenses).
Similar to my other scaners I like some additional protection for the lenses that don't obstruct the scanning capabilities so they can stay attached to the scanner. For this I just scanned the Sermoon P1 and did a quick model in…
The P1 arrives with a spare battery to quickly continue scanning after the first one dies. In its original case it has quite a nice and protected place but I like to toss the P1 in other cases or bags so the battery has to go with it.…
Kratší držák pakebláže od bedu, ten na Thing. je pro mě moc dlouhý a kabely se v nižších polohách moc kroutí.
