Counting matching models…
The 3D printed mount is designed to perfectly fit the Sonoff SNZB-03 Zigbee motion sensor, ensuring a snug and secure fit. Whether you prefer a more permanent installation with screws or a flexible and removable option with magnets, this…
A remake of the included mount for the SNZB-02D in case you want to make extras, and another mount for use on dry boxes. The other mount can also be used on windows, or any time you want to mount the sensor on the interior of something,…
Slim case for the Sonoff SNZB-02 ZigBee temperature and humidity sensor. This holder helps you to easily access the sensor without sticking it directly to the wall. Install the case with a screw or double sided tape and slide the sensor…
I wanted to mount the sensor to the underside of a self, and the included magnetic mount doesn't allow it to rotate close enough to horizontal. So I designed this clip, which has allowances for the top button and the USB-C socket on the…
The Sonoff SNZB-02 sensor is a simple and cheap ZigBee temperature and humidity sensor. The default mounting option is using a sticker to attach it to the wall. However, walls tend to be colder than the room they are in due to thermal…
EN: This stand allows you to place the Sonoff SNZB-06P presence sensor on flat surfaces like shelves or cupboards without wall mounting. Uses the included magnetic plate for secure hold Slot for easy routing of the USB cable Recommended…
Ich habe den Halter von Grund auf in OpenSCAD neu modelliert und unter der Basis sowohl Platz für einen Powerstrips Small, sowie Platz zum Entfernen geschaffen. Aufgrund der Bauart von Sensor und Switch halte ich ein Herausgleiten für…
This is a holder for the Sonoff SNZB-01 Zigbee Button
As these sensors use batteries, I wanted a mount where I can remove the sensor, replace battery and mount it again without the need to replace the double sided tape. This collection includes the following mounts for: SNZB-03 PIR sensor…
cradle for sonoff SNZB-03 motion sensor made with openscad Have fun!
It can be printed with 0.2mm layer height and with no supports, no need to rotate the models. Remove both the sensor and magnet from their original cases. Keep the screws holding the sensor PCB to the case as they will be used later. Push…
Outdoor case for the Sonoff SNZB-02P. I just taped the orange, magnetic mounting plate inside.
I've purchased a couple Sonoff SNZB-06P mmwave Zigbee sensors, but I didn't like that the size of the sensor was so large with the magnetic base. So I designed this back cover to make the device much smaller. It is possible to stick it…
Wall corner mount for SNZB-03. Designed for double-sided tape mounting. You can easily slide slide the motion sensor in and out if you want access connect button or replace battery. Print a little smaller in case you want friction when…
This is a holder to fit the Sonoff SNZB-02 Temperature and Humidity Sensor to the Ikea Skadis Pegboard. Category: Electronics
Originally made by puzon from Thingiverse.
Modification for Sonoff Temperature Sensor SNZB-02 that will allow use of 2xAAA batteries instead of a CR2450 battery. Why do you need such modification: - longer lifespan for battery compared to coin battery in terms of capacity - AAA…
You can donate here: https://www.paypal.com/donate/?hosted_button_id=BTTC6BR69RRAL Case for the Sonoff SNZB-02 ZigBee temperature and humidity sensor.
Pozwala wygodnie zamocować kontaktron Sonoff SNZB-04 ZigBee na oknach PCV.
This holder allows you to mount a Sonoff SNZB-05P water sensor to any surface in any orientation. It features a snug fit and retaining arms so the sensor can even be mounted upside-down. The sensor is easily removed for battery changes.…
The alignment of the reed switch is optimized, so its not missing an impulse of the gas meter. Just get the PCB out of your SNZB-04, put it in the clip and install the clip to your gas meter.
Einfacher Wandhalter für den SONOFF SNZB-02 Zigbee Temperatur/Luftfeuchtigkeit Sensor Ich habe hier eine einfachen, schnell zu druckenden Halter für einen SONOFF SNZB-02 Zigbee Temperatur/Luftfeuchtigkeit Sensor entworfen. Er wird mit…
I wanted to remotely measure temperature and humidity inside Creality Space Pi dryer. Also the built-in humidity dryer is not behaving reliable, as it won't go below 15 % R.H. So I used spare SNZB-02 thermometer for this, because it (so…
I made this so the button is not rambling arround the house and people know where to put it (if they take it out). I didn't want to glue the button directly to the wall, because it kinda reduces it's wireless functionality, hence this…
This is a mount for an inexpensive PIR motion sensor. They can easily be stuck flat on the wall, but if you want to put them up higher, you'll probably want to aim them down, hence the creation of this item. This mount fits Sonoff Zigbee…
The Sonoff SNZB-04 Door & Window Sensor is designed for blunt (is this correct? correct me in comments please) doors and windows. But most European doors have a rebate, which causes the sensor to fail. Hence, there was the need for a…
I wanted to place the Sonoff SNZB-04 Zigbee door sensor on my garden door to switch a light. I designed this housing to be water resisting as far as PLA printing is water resistant. It all fits snugly together with overlaps so that water…
I was replacing a Tuya sensor with a Sonoff SNZB-06P. I wanted to mount the sensor in ceiling, using the existing hole made by for the Tuya. This mount both accepts the Sonoff SNZB-06P, and cleanly uses the existing hole for the Tuya. If…
Inclined stand for the SONOFF SNZB-03 zigbee motion sensor. Printed in PLA with 0.2 mm quality. Simply fasten it with a wall screw through the hole provided, the sensor fits inside from the top and remains secure, allowing it to be…
I found the original case to be impractical and difficult to open. The model includes a snap in base plate for easily remove the sensor for battery replacement. Another advantage is that the battery is additionally fixed, which improves…
Alternative housing for Sonoff Zigbee motion sensor.
Hello, I made this model to add pool temperature to Home Assistant. Print well in ASA with 15% infill. I used glue to assemble the probe part with the float. You can screw a circle of plexiglass on top, protecting the Sonoff module.
The metal cradle which came with the sensor releases the double-sided tape within a day. And is orange anyway. So I made a plastic cradle which holds the tape well and also can be attached with the screw packed with the sensor. There is a…
Print with a support for the USB hole. Requires a bit of glue to connect the two pieces.
I printed it with PETG 3 perimeters 18% infill 0.6 nozzle 0.2 layer height
This simple model allows to put the Sonoff SNZB-02D inside your ACE Pro
SONOFF SNZB-02WD IP65 Zigbee LCD Smart Temperature Humidity Sensor holder.
Modification for Sonoff Temperature Sensor SNZB-02 that will allow to use 2xAAA batteries instead of build in CR2450. Why do you need such modificaton: - longer lifespan for battery compated to coin battery in temms of capacity and…
You can donate here: https://www.paypal.com/donate/?hosted_button_id=BTTC6BR69RRAL Držák na zeď pro senzor SNZB 02. Pro nalepení pomocí oboustrané lepící pásky nebo přišroubování. Možno použít i pro tlačítko SNZB 01. Pro tlačítko můžete…
PLA/PETG/ABS/ASA Infill 100 Brim No Support No
The switch was difficult to find on the bedside table at night, simply because it is so small. The switch also slips around quite a bit on a smooth surface. So I designed two different bases to make the switch more prominent. The V2 is a…
Give your Sonoff SNZB-03 motion sensor a "blinkered" view with this nifty 3D printed side cover! Perfect for making your sensor play a game of "I can't see you" in wider spaces. Slap it on, and voilà, no more alerts when your cat struts…
I want to use a Sonoff SNZB-04 Wireless Door/Window Sensor outside to check on the status of my yard gate. I neither trust the original case to be wind/water/weather proof, nor do I believe in sticky tape (especially outdoors). So I made…
This is a case to mount the new SONOFF IP65 Temperature Sensor. I just used double sided tape to stick it just outside my window but i included holes for countersunk 4mm screws. I printed it at an angle standing on one edge but i suppose…
For some reason, Sonoff decided to change the design of their old motion sensor (SNZB-03), which was neat and compact and great for ceilings, but with their new design (SNZB-03P) they decided to add a magnetic mount that adds 30mm of…
I made a mount for the Sonoff SNZB-03 sensor! Here are some details: Designed for : Sonoff SNZB-03 sensor. Screw hole : 3mm, for easy hanging. (example TX10 3mm Printing side : Sloped side should be on plate Strength : I used 4 walls for…
This wall mount is designed to match up to your remixed Sonoff SNZB-02 Temperature Sensor cases: https://www.printables.com/model/826509-sonoff-temperature-sensor-snzb-02-aaa-case-remix…
I replaced my hallway lights with smart bulbs (Zigbee), but wanted the switches to still be functional. Most existing options wouldn't work because my hallway lights are set up as a 4-way switch with no neutral wire. I bought Sonoff…
A housing to lift the senor away from the frame to align it with the magnet. This raises the sensor by 15mm, the sensor does NOT have to align flush with the magnet to work i believe a +- of 5/7mm will still work adequately. I decided to…
Remix with added 2mm thickness to base layer.
Battery Case for Sonoff Tuya Motion Sensor I have created a custom case designed to hold two AAA batteries, specifically tailored for the Sonoff-SNZB03 or other Tuya motion sensor. You can choose between two options for installation:…
I didn't want to stick it to the wall but hang it => spacer with a hole for the screw head. Nechtěl jsem lepit na zeď ale zavěsit => distanční podložka s otvorem na hlavu šroubu.
This is a remix of the SONOFF SNZB-02WD Temperature Sensor Desktop Stand posted by SONOFF on MakerWorld. This stand is designed to hold the SONOFF SNZB-02WD Smart Temperature and Humidity Sensor at an optimal viewing angle when placed on…
Simple mount for temrature and humidity sensor from Sonoff. Model SNZB-02. Can be printend without supports. Best printed with front on printplate. Material, layerheitht not important. Print without support.
If you want to use Sonoff Button SNZB-01 as a doorbell it might be difficult for your guests to recognize that ithe butt
If you open the box, there's just a small magnet inside. So I've made smaller case to fit in the space between the frame and window. You have to press a little bit harder to get the magnet inside and once you have it inside, it's not…
I wanted to add some motion sensors to my home automation setup, but don't like dealing with batteries. While there are products out there that directly go from a USB plug 5v to the 3v required by the Sonoff sensor, I had a few extra…
A simple kinda hidden wallmount for Sonoff SNZB-02LD Zigbee smart thermometer with four embedded magnets and screwholes Magnet size: 6x2mm and there is four holes for them, you might get away with only two magnets but i went with four.…
This is a remix to attach a Sonoff SNZB-06P Zigbee Human Presence Sensor to IKEA Skadis pegboards.
2 different stands for Sonoff SNZB-02LD thermometer with probe. 1st one is table stand and 2nd one is for rimless 5mm glass aquarium. Sensor goes in with pressing it in and there is hole in the back to push the thermometer back out for…
I wanted to use a Sonoff SNZB-02 temprature sensor outside. So I designed a ‘birdcage’ like holder. You can put the sensor in from under the unit. It has some holes to let air throug. Print without support if you put the roof on the…
Modification for Sonoff Temperature Sensor SNZB-02P that will allow use of 2xAAA batteries instead of a CR2477 “coin battery”. Why do you need such modification: - longer lifespan for battery compared to coin battery in terms of capacity…
Filament: PET-G Infill: 15% Support: Snug
French Ce support permet de ficher un capteur Sonoff SNZB-04P (ou Sonoff SNZB-04PR2) sur une porte de garage basculante. Il permet simplement par effet de gravité de déclencher ou pas le capteur. J'ai dessiné ce support lors de…
This is a bottom box for SNZB thermometer made by Sonoff, that is nice IoT device used with Zigbee. Problem is that SNZB battery (CR2450) is costy and lifetime is short, so this enclosure incorporate the electronic and even bigger battery…
Sensor mount for Sonoff SNZB-02P Outdoor housing: https://www.printables.com/model/1014449-outdoor-sensor-housing BOM 1x M4 threaded insert (https://cnckitchen.store/products/gewindeeinsatz-threaded-insert-m4-standard-50-stk-pcs) 1x M10…
A simple design to secure a Sonoff SNZB-02D Zigbee sensor to your Multiboard setup using a Flush snap. Use the magnetic support included with the sensor and attach it to the printed part with the provided double-sided tape. Ensure the…
This is a reupload of a full-size dummy model of the SONOFF SNZB-02WD Smart Temperature and Humidity Sensor. Here is the description provided from the original source: This is a 1:1 scale replica model of the SONOFF SNZB-02WD smart…
Штырьки для крепления находятся под уклом 4 градуса, что обеспечат нормальный прижим и не требует использования пластиковой лопатки для снятия, в отличии от стандартной крышки. Единственный его недостаток, что нет дополнительной поддержки…
This model gives a smooth surface for a refrigerator door to seal over the probe wire of the Sonoff SNZB-02LD. This allows you to mount the display outside of the appliance for readability while significantly reducing leaks from the gap…
Umbau der Knopfzelle auf 2 x AAA Batterien für den Sonoff SNZB-04 ZigBee Tür / Fenster Sensor. Gehäuse wurde auf einem Prusa MK3s+ gedruckt
Introduction Wanted to stop people touching the TV TV is mounted with a wall at other side of TV cabinet A correctly masked motion sensor at one side could be a good deterrent Vitamins Sonoff SNZB-03 PIR Motion Sensor etc. software for…
This is a door trim mount for the Sonoff SNZB-04 door sensor magnet component. Original idea and design was found from espn8theocho 's design found here: https://www.printables.com/model/704343-sonoff-snzb-04-spacersadapters (specifically…
an Opengrid case for the SNZB-02 sensor, with the form factor 43x43x14mm
Holder for attaching the probe to the place for the electric heating element.
I found this design and inparticular the remix the most elegant possiblity to raise the Sonoff SNZB-04 door/window sensor to allow for sensor and magnet aligment. No need for overhangs or support, perfect printing direction for the…
A housing to lift the senor away from the frame to align it with the magnet. This raises the sensor by 15mm, the sensor does NOT have to align flush with the magnet to work i believe a +- of 5/7mm will still work adequately. I decided to…
This is an adapter for mounting a Sonoff SNZB-02 Zigbee temperature and humidity sensor to a steel column. It uses three magnets harvested from a spent Philips Sonicare toothbrush head (essentially free). Arrange the magnets so they…
Rocker cover that holds a SONOFF SNZB-01P Zigbee button. Still provides access to the switch if needed but makes the button the primary object. Useful for when your kids keep flipping the non-smart switch.
I wanted an unobtrusive right-angle mount for the Sonoff SNZB-06P presence sensor that kept some of the nice properties of the original included mount (magnetically adjustable), but could easily be attached at right-angles to the forward…
Flush mount adapter for the Sonoff SNZB-06P presence sensor designed for the Gira System 55 switch system. The design consists of: a modified Gira System 55 blind cover a slotted sensor sleeve with integrated cable routing The cable slot…
Eine einfache Halterung zur Befestigung des SNZB04 an einem Velux-Dachfenster. Durch die Positionierung in einer der oberen Ecken kann das Dachfenster vollständig geöffnet werden, ohne dass der Sensor im Weg ist. Der Sockel überbrückt…
This is a wall mount for the SNZB-02 ( https://zigbee.blakadder.com/Sonoff_SNZB-02.html ) air temperature and moisture sensor by Sonoff . The Sensor comes with sticky tape and is supposed to be taped to a surface directly. If you stick it…
All the parts are assembled using glue. Also I used a permanent acrylic marker to outline it. FF-SNZB02-COVER – optional. Based on and in the style of this model https://www.printables.com/model/1433993-flashforge-adventurer-5m-air-locker
In das Gehäuse kann ein Sonoff SNZB-02 Temperatursensor mit einer CR123A Batterie betrieben werden. Der Batteriedeckel wird entfernt und die Batterie mit zwei Drähten an den Polen des SNZB-02 angelötet. Der Batteriehalter kann separat…
In der Box des Sonoff SNZB-06P Präsenzmelders waren 3 Kabelhalterungen mit angebrachtem Klebestreifen enthalten. Da mir diese zu wenig waren, habe ich diese rekonstruiert.
This is an adjustable magnet holder for the Sonoff SNZB-04 door/window switch. The measurements of the provided files are: 20 (base) × 28 mm (protrusion). The original magnet is assumed to be 20 mm long, and have a diameter of 4 mm. It…
Annoyed by constant battery changes on your Sonoff SNZB-03 motion sensor? The standard coin cells drain way too fast. This 3D-printed replacement housing solves the problem once and for all! With this mod, you can convert the motion…
Housing pro teplotní čidlo domácí automatizace, SNZB-02 od Sonoff. Jistě se potýkáte s krátkou životností baterie CR-2032. Tento housing jsem udělal, aby bylo možné 3V baterii nahradit 2x AA nebo 2x AAA bateriemi, které mají výrazně vyšší…
A insert for SNZB-02 with AAA or AA battery box that improves lifetime of sensor. Used housing (Kopos, LK and VLK 80) is very cheap and UL (fire) resistant for indoor electrical installations.
Holder for Sonoff SNZB-03 motion detector.
Introduction If you have Sonoff's SHZB-02P s you can place them on ferromagnetic surfaces already, since they are magnetic. If you want to stick them to a non-ferromagnetic sheet (like the wall of a plastic container) you'll need a…
This is just a small holder for the sonoff zigbee temperature and humidity sensor SNZB-02B. One of the cheapest an most reliable sensor on the market, it uses 2 AAA batteries - great! Print it with a little support. Using one screw to…
Sensor mount for Sonoff SNZB-02P Outdoor housing: https://www.printables.com/model/1014449-outdoor-sensor-housing BOM 1x M4 threaded insert (https://cnckitchen.store/products/gewindeeinsatz-threaded-insert-m4-standard-50-stk-pcs) 1x M10…
I didn't want to stick it to the wall but hang it => spacer with a hole for the screw head. Nechtěl jsem lepit na zeď ale zavěsit => distanční podložka s otvorem na hlavu šroubu.
This simple model allows to put the Sonoff SNZB-02D inside your ACE Pro
Holder (header jamb) for SNZB-06P I made a mount for the sensor because I was tired of using adhesive tape. Supports = Yes
A simple kinda hidden wallmount for Sonoff SNZB-02LD Zigbee smart thermometer with four embedded magnets and screwholes Magnet size: 6x2mm and there is four holes for them, you might get away with only two magnets but i went with four.…
I was replacing a Tuya sensor with a Sonoff SNZB-06P. I wanted to mount the sensor in ceiling, using the existing hole made by for the Tuya. This mount both accepts the Sonoff SNZB-06P, and cleanly uses the existing hole for the Tuya. If…
I wanted an unobtrusive right-angle mount for the Sonoff SNZB-06P presence sensor that kept some of the nice properties of the original included mount (magnetically adjustable), but could easily be attached at right-angles to the forward…
![Halter SONOFF SNZB-02 Zigbee Temperatur/Luftfeuchtigkeit Sensor [Holder SONOFF SNZB-02 Zigbee temperature/humidity sensor]](https://media.printables.com/media/prints/629178/images/4985457_f304ef28-adfc-4b7d-8e8c-93f9f1efc433_ee66351f-ad5c-4333-83ac-390003d84f66/img_20231028_130456.jpg)
