Counting matching models…
Why would you need this instead of buying a cheap replacement? Made to fit a Danfoss thermostatic radiator valve. Allowed me to turn off the radiator and push the valve's pin back. How to use: Press fit one half onto the valve The half is…
The latch of the battery compartment lid is often damaged. Here is the solution.
Replacement of Lidl Livarno thermostatic shower mixer's end cap. Print it with 0.3 layer of finer, PET-G preferred.
This is an adapter for the handle on a MIOMARE® Thermostatic Mixer Shower. The handle on this mixer shower is unsuitable for operating with soapy hands thus I designed this adapter. Print instructions Printer: Prusa Mini Material: PLA…
I created a housing for the Tuya thermostatic head. Unfortunately, the locking cap is severely unfinished and breaks off very easily. If the lock breaks and the cap does not stay in place, there will be a power problem. In this case,…
Story: I usually just get shower to save water, so I bought a thermostatic shower faucet, but after a long day it's nice to sit in the bath, but than it was hard to fill the bath with a water, because it is not a bath filler tap, so I…
Here is my take on converting the 3x AA batteries into a dual 1S2P 18650 rechargeable battery for my TRV 604/TRV602 My TRV604 are mounted on Danfoss RA valves. I used around 60 AA batteries in 6 months with these thermostatic valves. I…
Hello Adapter for thermostatic valves M30 x 1.5 Print in ABS with automatic support. 1 screw => M4x10 1 nut M4 (For my part, mounted on a DELTA DORE TRV1.0 valve) Good print
Replacement for the OEM grey plastic connecting nipple that sits between a Villeroy & Boch (or Gustavsberg) thermostatic shower bar valve body and the shower hose. The original part is a small grey plastic piece that can crack. The…
These original end caps have a very limited longevity... so i designed a replacement. Sadly 3D prints along layer lines like this one are not any better but at least i can make them anytime. Made to fit Siko Thermostatic bath faucet pro…
Replace the parts: carter3op-cr40 The genuine product it too fragile and it's difficult to find a new kit. So I decided to create my own kit, stronger than the original one.…
As the original red knob broke, I decided to replace it with the very same but 3d printed. Printed in PETG Prusament Lipstick Red. The bottom part needs support so the top part can be rounded.
Printed in PETG. 2 wall loops. 2 top/bottom layers. 10% infill. Don't make it too stiff, otherwise it won't fit into the radiator valve. Create a 19 mm diameter, 16 mm high cylinder as a piston to connect the thermostat pin to the valve…
Once again, the thread on my Chinese mixer stripped, but I didn’t have a spare adapter on hand. So I drew one, along with a gear. My rod is 7.7 mm in diameter, and the adapter is 7.8 mm, but it still fits with some force, so that the gear…
Original knobs slip so I've designed these. Openscad code is not cleaned but it works. When installing put it lightly on and screw it into position. Screw will do the hard job because the print is slightly thicker but the plastic will…
The Grohe Grotemp Thermostatic Faucet has one glaring problem. The little cap that pushes into the valve that changes the temp of the water is just a rod threaded into plastic. It has broken multiple times. I decided to make one with an…
Simple replacement knob. Push fit onto splined valve stem. May need a few taps with a mallet to encourage it. Print with the end face down, no support needed. I used 4 wall, 3 top, 3 bottom layers, 0.2mm in PETG. May redesign in the…
In order to heat the enclosure I'm building, I need a controller and heat source. I found this 24vdc thermostat that can switch mains power and I'm controlling a 275W infrared heat lamp. This little rig works like a charm and has an all…
If it starts to flex (like mine did) print the additional clip to hold it in place. If you use glue (between the hanger and the clip) it will be better.
The latch of the battery compartment lid is often damaged. Here is the solution.
Thermostatic Valve HY368-ZB Battery Adapter Modification I have performed a modification on the Thermostatic Valve HY368-ZB by enhancing its battery adapter to improve performance and user convenience. Project RAW Power Module and used…
I've designed a custom 3D printed pin that will mechanically adjust the thermostatic valve's setpoint to prevent it from opening during ventilation in an unheated bedroom.
Handle to fit a Meynell Thermostatic Mixer Shower. This fit both the shower cubicle mixer valve and the bath tap combination mixer valve. My daughter struggles to turn the tap as it is quite stiff and needs more torque in order to turn…
Here is my take on converting the 3x AA batteries into a dual 1S2P 18650 rechargeable battery for my TRV 604/TRV602 My TRV604 are mounted on Danfoss RA valves. I used around 60 AA batteries in 6 months with these thermostatic valves. I…
