104 models
Turn your old empty filament reel into a trackball toy for your cat! Tracks fit any filament reel size, just use the connector to join and hide any gaps. You can use any ball that's ~53-55mm large. A heavier ball seems to be more…
Printed it with 10% grid infill, 0.30mm layer height and two perimeters. This leads to a very light print, but putting some EPDM pads on the bottom prevents it from slipping around your desk.
A 45° wedge stand to hold the Logitech M570 trackball mouse. Held in place via ball and battery holes. Place to store battery cover. Find ergonomics better than flat and takes up less space. Print instructions Wedge print is hard plastic.…
A stand to make the Logitech M575 angled at 30 degrees for ergonomics. This will lock tightly to the bottom of the mouse
This is a USB trackball, made using: a 57.2mm billiard ball PMW3360 optical sensor the PCB from here: https://github.com/jfedor2/rp2040-pmw3360 Kailh GM mouse button switches (or any other switch with the same footprint) this PCB for…
New version available. The Pimoroni version is not supported anymore (firmware need to be built with v23 which is outdated). But if you prefer the small size and you are prepared to downgrade your firmware, it works perfectly well. There…
Two styles here: Tilt with forward angle (normal desk use) Tilt up with lower anchor to hold in place (for my poor basement ergo setup) I like to keep two variations on desk and swap every few days to avoid repetitive injury, I think that…
My collection of self designed OLED covers for CRKBD/Corne. Update 10th Nov 2021: added DXF file for pimoroni trackball version. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2mm Infill: 10…
I need to model a backpack proof case for my Logitech MX Ergo, therefore I needed to scan it. Here's the STL, maybe it's of use to somebody. I have only made a rough scan, didn't get all the crevices and cleaned it up quickly in Blender.…
Latest version of my Logitech M575 trackball 45 degree angled base. The primary change was to increase the diameter of the anti-rotation pins to increase their robustness. The angle of rotation on the 45 degree plane was also increased…
A 45° wedge stand to hold the Logitech M575 trackball mouse. Held in place via ball and battery holes. Place to store battery cover. Find ergonomics better than flat and takes up less space. Print instructions Wedge print is hard plastic.…
Stand for Elecom Deft Pro trackball. Three options available: 10 degree tilt 15 degree tilt 20 degree tilt Category: Computer
This sits under the trackball and changes its working angle to 45 degrees which is much more comfortable for the arm and takes pressure off the carpal nerve in the wrist. I printed this with 5% infill which is plenty strong enough. Once…
This is a functional zero-button USB trackball. Click with your keyboard or some other way. It was made using: a 38mm billiard ball PMW3360 optical sensor the PCB from here: https://github.com/jfedor2/rp2040-pmw3360 2.5mm zirconium oxide…
Parts list Logitech M575 mouse 1 AA battery holder 5 m2.5x8mm screws Double sided nano tape Soldering equipment Instructions Print the thumb cluster model and replace the stock thumb cluster with it. Print the wedge model, and secure it…
This is a functional two-button USB trackball. It was made using: a 57.2mm billiard ball PMW3360 optical sensor the PCB from here: https://github.com/jfedor2/rp2040-pmw3360 Kailh GM mouse button switches (or any other switch with the same…
This is a mount for the Kensington Orbit trackball. I designed this specifically for attaching to 1530 aluminum extrusion, but it will also work for attaching to any flat surface. Has 15 chamfered screw holes for a variety of…
The same as Ebachalo's but as one piece vs two. Original: https://www.printables.com/model/52753-logitech-m570-trackball-wedge-stand-45deg Print settings: Prusa Slicer, Supports: auto gen supports, overhang 45, style organic, top contact…
Trackball: https://amzn.to/46RovXb or https://www.protoarc.com/products/em01-advanced-wireless-rgb-trackball?variant=40089402474585 It's a good replacement for Logitech MX Ergo. More sensitivity settings, support for 3 devices and USB-C…
This is the base plate for MX Ergo, can be used as a replacement for the original metal one. I made it to design a trackball based on the same plate. Compatible with other stands. 4 x 10mm x 1.5mm magnets Superglue 4 x Rubber feet Print…
Simple tent mount for Logitech M575 trackball. Pictures show a 10deg tilt. There are models for 10, 15, 20, 30, and 45 degree tilts.
I need to model a backpack proof case for my Logitech MX Ergo, therefore I needed to scan it. Here's the STL, maybe it's of use to somebody. I have only made a rough scan, didn't get all the crevices and cleaned it up quickly in Blender.…
Requires three NL-8H (8mm) ball transfer units (BTU) like these: https://www.amazon.com/dp/B081QKS4S2 If you don't have a spare trackball ball to pop into it, one of these should work:…
This is designed for a Logitech M575 Trackball Mouse. Others may work, but the contour in the part is shaped specifically for this mouse. I've been incredibly busy at work recently and I've notice my mouse wrist has started to feel some…
mirror bot_nomal, pro_micro_adapter for left, right mouse sensor using ADNS9800 need 50 switchs, diodes, hotwaps ( kailh, gateron or something else) firmware is QMK, can use Promicro atmega32u4, blackbill stm32f401, RP2040.... Ball is of…
This is a functional zero-button USB trackball. Click with your keyboard or some other way. It was made using: a 57.2mm billiard ball PMW3360 optical sensor the PCB from here: https://github.com/jfedor2/rp2040-pmw3360 2.5mm zirconium…
Logitech M575 trackball mouse tenting wedge remix with 12deg left to right and 5deg front to back tilt.
This is a USB trackball, made using: a 38mm billiard ball PMW3360 optical sensor the PCB from here: https://github.com/jfedor2/rp2040-pmw3360 Kailh GM mouse button switches (or any other switch with the same footprint) this PCB for…
This is a replacement optical wheel for a 4.5" Atari trackball used in several Atari arcade games from the 1980s. These include Missile Command, Football, Baseball, Basketball, Soccer. There are two versions of the wheel. The original…
傾きを15度、前傾を3度増やし、元のモデルより上腕のひねりと手首の角度が楽になるように調整しました。 バージョン2 高さを抑え、傾きを減らしました。
I found ball-transfer-units (BTUs) provide a smoother mousing experience. Inspired by bomtarnes . Details about the BTUs I used for this model: R053010810 Bosch Rexroth Ball Transfer Unit US Store:…
This is a battery cover for the Logitech M575 trackball mouse. I couldn't get warranty support for the lost cover, so I made a 3D model of it. If you have lost your battery cover as well, this should help. Print Settings Printer Brand:…
Simple tool to make it easier to remove the trackball for cleaning. Sized for the Logitech Ergo M575.
I was looking for a USB arcade trackball to use at home and all I could find are ones to bolt into an arcade control panel nothing ready to go that I could use in my lap/desk so I designed this one. Parts used - The trackball itself -…
Changelog: 2026-06-08 updated to v0.2. adjusted depression for battery door. Accidentally had m6x16 in BOM which should be m6x20mm. I added a m6x16 version for m575. 2026-06-08 added beta logitech m575 mount based on…
A trackball housing for a 34mm trackball.
Here you can get a holder for the Logitech M570 Trackball mouse. See the drawing for dimensions.
Designed this top shell to replace the shroud that comes attached over the pimoroni trackball. The stock trackball shell is removed by gently squeezing the retention clips together underneath the PCB. The additional purposes of the shell…
UPDATE (09/08/24): STL version now available! --- Ok, so as I said in my previous upload (55mm Trackball), I'm not suggesting you go out and buy a Kensington Orbit, Adesso iMouse or Logitech Trackman Marble Mouse just to get a 40mm…
Mount for a Logitech M570 Wireless Trackball Mouse Two versions for either M5x16 or M6x16 bolts to Profile. Bolt holes are on a 20mm grid with the corners at 40mm It uses Velcro 3/4 Coins to hold the mouse to the tray. The image is from…
These brackets let you customize how the Navigator trackball integrates with your Voyager keyboard . They reuse the magnet, screws, and back-plate from the original Navigator mount or buy 60x13.5x5mm magnets for example from Amazon and…
This is a connector piece that holds the wrist rest to the trackball for the Kensington Expert Trackball Mouse. This model appears to work for the wireless version of this mouse as well. I'm sure there are ‘better’ solutions, but this is…
New breakout box that incorporates the larger 1.3" OLED screen and a Trackball which is now supported by the latest version of FlashFloppy v2+ ( https://github.com/keirf/FlashFloppy/wiki/Hardware-Mods#blackberry-trackball ). Recommend…
UPDATE: Finally released from the Patreon, STL files are available! Ok, so firstly, I'm not suggesting you go out and buy a Kensington Expert, Slimblade or Perixx Periboard just to get a 55mm trackball to use with this system. That…
These ready to print drop-in inserts will help you convert your Ploopy Rev. D from using the standard roller dowel style bearings to 2-mm ceramic G5-grade bearings. It may work on earlier revisions of the Ploopy, but this is not the STEP…
This is a functional one-button USB trackball shaped like a sphere. It does not sit on a desk, you have to hold it in your hand. It was made using: a 57.2mm billiard ball PMW3360 optical sensor the PCB from here:…
An enclosure for a trackball and 3 buttons. The devices compatible with this design are: https://www.amazon.com/gp/product/B06Y18STSR https://www.amazon.com/gp/product/B07X242Z4D A bit of soldering, and it should just snap together.
https://github.com/brickbots/aball ← Link to Original Open Source Project Hello! This is a modification + Extra bottom plate i made for my aball trackball project. It adds much more thickness, areas for 6mm rubber feet, and inset M2 nut…
This is a thingy that helps with ejecting the trackball of a Logitech MX Ergo. I didn't need this with my old M570, as the hole below the trackball was large enough for my pinky finger to poke through. The MX Ergo's one is much smaller…
The tail end of this model is 170% the length of the original model. In total, it adds about 4cm of extra space for your palm to rest. It's not pretty, but it feels way better for my hand. The parts are backwards compatible so, you could…
I'm toying with plans for a custom game controller including a trackball, and this experiment in mounting a trackball securely while allowing it to spin freely is a step towards that. My first prototype looked a bit like a fancy desk toy,…
This base allows you to set your efog.tech Endgame trackball at an angle. It connects to the Endgame with a collar, allowing you to rotate it to adjust the tilting and tenting. As you rotate the base, you'll raise one corner while…
This all started with a thread from Reddit, where someone had tried to identify a trackball that an editor was seen using in a screenshot. Turned out to be an ordinary Logitech m570 on a wedge. After some discussion, someone suggested it…
The Huge trackball is great except when the ball sticks when it is moved across the screen. Here is a simple fix without taking the entire trackball apart. Print two cups and place them on top of the screw holes under the main trackball.…
The Ploopy Nano is a great little trackball that's just a trackball. No mouse buttons! There are, however, contacts on the PCB to put the trackball into bootloader mode (by shorting them with a paperclip), and these can be used to add a…
Fair warning. I've used TinkerCAD because I lack proficiency in other, better/professional solutions. After purchasing the Ploopy Thumb Trackball, I knew I would be immediately adding the Rexroth BTU mod as well as adding a steel…
Mount for Logitech M575 trackball. After printing just add a 1/4-20 nut.
This remix is to extend the centre pillar to push the trackball a little bit further.
I'm using my Gotek in an external case, so I wanted the screen to be on the top for better readability, I also decided to switch to using the Blackberry style trackball so put that on top too, With both of those up there and the trackball…
FR Le syndrome du canal carpien et le syndrome de la souris sont multi causaux. Parmi ces causes, on retrouve une mauvaise position pour l'utilisation du clavier et de la souris. Le support réglable pour trackball 'SRT" n'est pas un…
This is a spring loaded clamping mechanism to mount the Kensington Orbit trackball to a sim rig. The spring allows easy access to the device for example for battery change, power switch or if it's too far away for easy use and should be…
Print with material and settings of your choice, but the heavier, the better. Then print the original model ( https://www.printables.com/model/723722-kensington-orbit-trackball-mount ) according to their recommendations. I suggest PETG…
OddBall Split Keyboard The OddBall was designed mainly as a learning project to help me better understand how wiring a trackball breakout board works with ZMK before eventually designing my own PCB. It is a fully hand-wired split keyboard…
I love the Ploopy Trackball but needed more of an angle for my wrist so I made the Ploopy Wedge. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .20 Infill: 15-35 Notes: I went with 35% infill to…
Trackball's cover for keyboards Cherry G84-4400 or Active Key Ak-440-TU-B + tracking ball like a bonus. Is necessary to finish printed models with sandpaper or by file.
My 3d printable kyria OLED covers, including the pimoroni trackball holder. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 10 Filament: PolyMaker PETG/PLA Category: Computer
This is a spacer for the Pimoroni Trackball. I used this to get my Lily58l (not every Lily58 can handle a pimoroni) running. The trackball has some components underneath, so it cant be soldered flush on any PCB. I designed a spacer it can…
A stand for the MT50 Trackball that allows it to be set at a 20 degree angle, and you can also store the original USB receiver in it. In addition to the PETG filament, you will need a 6x3x2mm magnet and 6 pieces of 4.5x1.8mm rubber feet
The Navigator Trackball is ultra-smooth, up there with the best trackballs, when using your board flat or at a slight angle. This print lets you continue using the Trackball even at higher tenting angles. You won't need any supports or…
If you're one of the crazy ones who doesn't use the trackballs and they get in the way, why not replace them with these? (I've moved my whole operation over to DCTLs) These rings still allow to control the Y channel by interfacing with…
Improved version of the angled wedge for the ProtoArc EM03 trackball. Modifications: By default the bottom of the wedge is flat. By adding little silicon feets, the double sided tape tend to slip causing the mouse to be crooked. So I…
This is a mount for the pimoroni trackball to go on a kyria keyboard . The 3 similar designs (not the "original") would probably fit in any case, but the original is pretty specific to the case found here , which can also be seen in the…
This is a replacement panel that lets you mount a couple of MX-style switches in place of LMB and RMB buttons. The model is a remix of the 3D scan by Wesk (thank you very much). Having a X05 revision of the trackball on hand, I couldn't…
I'm using it for the EM01 NL.
A mount for the Navigator ( https://www.zsa.io/voyager/navigator ) for the moonlander. This is very similar to this model (https://www.printables.com/model/1402746-zsa-moonlander-mount-for-navigator), however I wanted the trackball to be…
Please post your makes 😁 UPDATE - Version 2 added, it fits a bit better. Adds an extra 13, 20, or 25 degrees of tilt to the ProtoArc Wireless Trackball EM01 NL. I recommend thin rubber feet on the base. Step file available upon request.
This is a form fitting trackball tray and support for the Logitech M570 Wireless Trackball Mouse and mounts to my SimLab PSE USB Wheel mount back. It uses M3 bolts and M3 threaded inserts as well as "VELCRO Brand - Sticky Back Hook and…
Support pour incliner le trackball et en faciliter l'accessibilité pour une personne en situation de handicap. Imprimé en PLA, sur le côté, sans supports
This is a simple holder for a 34mm ball for a trackball mouse
Read more on my website: http://tennojim.xyz/article/x-keys_l-trac Here are all the details before assembling: 1) As rollers I got a set of high-quality miniature bearings with an outer diameter of 8mm, inner diameter of 4mm and a…
A handwired trackball with a 38 mm billiard ball and a PMW3389 sensor, in two versions: wired on an RP2040-Zero running QMK with Vial, and wireless on a nice!nano running ZMK. The wired case comes with one, two or three buttons, the…
Mount for Pimoroni trackball on a Kyria keyboard This mount enables you to mount the Pimoroni trackball within comfortable reach for your thumb. This will be mounted where one of the switches would go. I've only tried this with lowprofile…
A trackball seemed like a unique way to utilize a mouse built to be modular! Levers were used to decrease the force needed to actuate the switches while directing force into the hardware switches straight-on. Printing Print out three (3)…
This mod allow a perfect integration of ZSA Navigator in right thumb cluster of your Moonlander. Why to choose this mod No cables tangling around (we use the flat ribbon cable included in your Moonlander) No firmware modding needed. Just…
The original hinges didn't strike me as rugged, so I made an attempt at improving on the design. It works well for me. I would consider adjusting some clearances if I was going to print a second version, but I do not plan on further…
print recommendations: layer height: 0.2mm for the first layer, 0.1 for others; concentric top surface pattern; seam position - back; 7% infill is enough
Mezi víkem a krabičkou je mezera proti přiskřípnutí kabelu.
I love trackballs. I think it's because my first PC was a 386SX 20 and it came with a 3 button trackball and a 14" VGA monitor that was longer (from front to back) than it was wide. It was glorious, no soundcard, just a PC speaker... I…
Kongsberg K-Pos 21 DP operator stations have common faults with the mouse and heading wheel buttons. this is due to the small plastic part wearing that presses the metal button disk underneath. kongsberg will only offer for sale the full…
Logitech M570 trackball replacement rubber feet. I'm loosing these sometimes. Printed from Fiberflex 30D, 0.15 mm layer height. Installed using thin double sided tape.
Give this model a try if you would like a more natural wrist position when using your X-keys trackball . These trackballs are excellent quality and a great alternative for those who get wrist pain from using computer mice. My X-Keys…
I designed a stand that can change the inclination of the trackball mouse. Print Settings Printer: Geeetech i3 Pro B Rafts: No Supports: No Resolution: 0.2 Infill: 25% Filament: Other PLA transpearent Notes: By moving the USB dongle's…
The trackball3D is a computer input device made for any axis rotation of camera view in pymol molecular visualizations. Unlike traditional 2D input devices like mouse, trackpad or ordinary trackball, this device senses rotations of a ball…
This is a bordering cap for trackball mounting on self-made Arcade Machine.
The Kensington Expert Trackball mouse pad that makes it horizontal and has space for a soft cushion/wrist pad. The model can be tuned in the the original FreeCAD source. Personally, I printed it twice (the first one didn't have place for…
A fine trackball companion accessory for a keyboard, like the Logitech MX Mechanical keyboard; when a mouse isn't good enough... Or a simple pointing device for a driving sim rig. Required hardware: 1 x Logitech M240 Compact Silent…
I was given one of these keyboards from an old point of sale terminal and asked if I could make a desktop case for it, here are the results. Each half was made to fit on a Prusa MK3, and they lock into each other with a pair of dovetail…
I have an issue with the ZSA Voyager Navigator Trackball. It is useless with 45 deg. tenting and the trackball frequently dropped when I moved or packed the keyboard. I designed this Trap as my solution to those problems, making the ZSA…
link https://www.aliexpress.com/item/1005005935808665.html home made supporto 15° for trackball
Sanwa MA-TB39BK passend zur Spacemouse 3D
![Filament reel trackball [fits any brand]](https://media.printables.com/media/prints/414022/images/3435490_cad3b8db-ddf0-4223-8f22-a2cb65a6381d/wtf.jpg)
