Counting matching models…
I have developed a chain drive for Traxxas TRX4 RC cars, which can be almost completely 3D printed. All you need are a few ball bearings and M3 screws. The drive train is fully functional and has already been tested extensively (in snow…
1/18 scale version of the original 1/10 by MrStolarsky. Pins were re-aligned and the whole board was made stackable. I test printed mine in resin and they came out awesome. I designed hangers for the Traxxas TRX-4M Defender, to hang a…
A simple shackle for my Traxxas TRX-4M Defender bumpers. Printed in resin and painted. Paper clip can be used to be pressed in to fasten it to the bumpers. Drop of glue might be needed at the ends to secure the paper clip in (I did not…
Wheels for the Traxxass TRX-4M Defender. All fit the original rubber and have the same offset as stock by default. Alternate versions with +X push the wheel out by Xmm, the wheel sits further out. -X brings the wheel closer to the body by…
Front light guard for my Traxxas TRX-4M Defender. I printed mine in resin and glued them on. Print some spares as the thin tubes might get broken in print (0.5mm in diameter). I printed 4 at a time and one guard had one bar broken.…
Designed these to use with my Traxxas E-Revo VXL 1/16. Its a dual extrusion print. I used PLA (green) and Flex (black). These tires drift more than the other tires we can buy for the RC cars. I tried several tires with different flexible…
Remixed from a scx24 snowplow. Replaces front bumper. Body does not clip in unless someone wants to remix it. Requires 2 m2x6 screws and a paperclip.
This is a stand for the Traxxas Trx4m crawlers. It sits on the front and rear links of the vehicle. All parts are posted in the orientation of how they should be printed. Roughly 1hr 45min to print dependant on settings. 4 pieces then…
12mm Hex Wheel Hubs for 5mm axles. Work on 2WD and 4WD vehicles. 12mm hex in various widths from 4mm to 12mm. Perfect for adjusting fit when using alternative tires and bodies. Category: R/C Vehicles
7mm long drive hex for the Traxxas TRX-4M Defender. I did not like how the axle thread is vissible with the stock hex drives (just asking to be damaged). This one is just long enough to have the nut flush with the end of the thread while…
Hi, I just finished the rework of some kind of sump boat which I designed for my son. It just started with a simple idea of having our Traxxas Blast boat modified a little bit but it ended with 26 parts for the boat itself, 9 parts for a…
Hi, It's my air funnel for 30mm and 25mm fan.
I posted these before on thingyverse, but I dont like that site, just too slow, so as I am moving to this, thought I would share the design here too.
a big beefy battery mount that has stood up to a lot of abuse. Print instructions Unassociated tags: r/c Category: R/C Vehicles
I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf…
I designed this stand for placement in my display case. Support is needed. Printed with PETG.
I just want to say that these really do fling dirt / rocks / gravel behind them in a HUGE arc. These tires are not good if you are around anyone who does not want to get peppered with rocks and dirt. These can easily fling rocks 30 feet…
Why? I needed space under the stairs :-) Features: Stable wall mount to grab the rear or frontal inferior wishbones Rc cars suspension locks the car in place and garantees a firm hold to the wall Width is designed for a WideMaxx Kit or…
EDIT 2 Here are the 0.85" wide rims and tire for the front of your 2WD if you want that dune buggy look. EDIT 1 I added rim design 011 through 014. I also slightly modified rim 008 by adding an 0.030" fillet on the top edges. ORIGINAL My…
This is a fully printable wheelie bar that fits RPM and Stock bumper mounts for Traxxas 1/10 scale 2wd Cars and Trucks including the Bandit, Rustler, Stampede and the Slash. I have printed it in PETG at 0.15 and 0.20 layer height at 6…
EDIT: updated with newer design This is the a-arm for the 1/10 scale 4x4 traxxas slash. it has the normal mounting holes in the front for the shock, but it also has mounting holes in the rear so you can mount another shock to the rear of…
This is the fourth and final iteration of paddle tires for my and my sons' Traxxas Rustler 2x4 and 4x4 trucks. These paddle sleeves (as I call them) are compatible with the rims here which cam be printed in PLA, and are very durable. Here…
Schneereifen, Sandreifen, Schaufelreifen für Traxxas Maxx und andere RC-Autos. Macht im Schnee sehr viel Spaß. Absolute Empfehlung! Sehr leicht konstruiert um Material und Druckzeit zu sparen. Trotzdem ist der Schneereifen sehr stabile…
Just a simple set of hooks to hang the tires of my traxxas slash off the wall and save some space.
A kit I created for my friends rc car. It should protect the car's body on a rollover - the way he drives, there are many rollovers believe me. :D Important is, this kit will not fit on the original X-Maxx body, it's designed to fit on…
Allows you to turn the esc on and off with the body on, uses the esc mounting holes, and a spare 3mm screw. More info to come. Update 8/21/17: Thickened the rocker in places, noticed the key could slide past the rocker and into the body,…
Traxxas 2WD battery hold down straps for Rustler, Bandit and 2WD Stampede. These easy to misplace parts are easily printed. For fun, I added an inscribed TRAXXAS logo on both sides. I've used both PETG and ABS. For best strength, print…
I had to raise the body to fit a heatsink with a fan, and the original spoiler touched the body so it would not fit properly, so i made my own design. I printed it with a 0.3 mm nozzle at 0.1mm layer height and support. Iprinted it…
The Nick.CNC mid motor conversion allows you to convert your Traxxas 2wd vehicle to a modern mid motor layout for better handling. All the files needed to print and CNC cut your parts are included. Don't have a CNC? You can send the step…
This is an 8mm tall spring preload spacer, designed for any traxxas vehicle with shocks that use preload spacers on the springs. These snap over the shock cylinder, to increase the preload. Very simple to scale to various thicknesses.…
Measurements taken from my Traxxas Eagle stadium truck Printed in add:north Adura X (nylon + carbon fiber). Probably works in other materials as well!
Front GoPro mount for the Traxxas slash
Why? I needed space under the stairs :-) Features: Stable wall mount to grab the rear inferior wishbones Rc cars suspension locks the car in place and garantees a firm hold to the wall Requirements: I printed the mount with a 0,6 nozzle,…
This spoiler gives your Traxxas Rustler 2wd a unique and custom look. Be sure to print at 100% infill so it won't break. Use the original hardware to attach. enjoy! If you like this model, please give it a like! And don't forget to…
Over-beefy hangers for my Traxxas TRX-4M Defender. Might work for other crawlers/rc cars. Designed for a 56mm tall tyre. Distance between inner tyre walls to be 75mm (or 75 ±40, peg holes are 40mm apart). Right wheel hanger (uploaded)…
Customise your own fender vent via slicer with different infill patterns. In my case i used superslicer. Settings: 1 bottom layer, 0 top layers, 31% monotonic infill and 4 Vertical Shells. Quality on Top surfaces disabled. Material:…
If you want to use Losi Mini-T springs on your Traxxas TRX4 shocks, these spring perches will allow you to make the conversion. The lower perch is designed to allow popping it off over the shock shaft without removing the rod end, so…
A component of the parts kit 3768. It is a cone shaped lower spring retainer for my 4x4 Rustler vxl. I got my ruslter and took it out for a spin. It collected every kid in the neighborhood! An hour later after they had all had a bash, I…
I have a Traxxas TRX4m, I drove it so much that I got tired of using two hands. So I went into Fusion 360 and fixed my problem. I would recommend TPU but PLA or something like that will work. I recommend printing the nob at 100% infill…
This is a steering block I remixed from Sidpatchy's model . I made the piece that attaches to the steering assembly a little bit thicker to make it more durable. Link to the original Traxxas product here Compatibility: Traxxas Bandit…
Mirrored original to get right side. Print at angle with supports. These hold up very well.
Not my file. Reuploaded for my collection Thingiverse thing:5733107 by GreiniStyle
RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG may still need some tweaking. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. I had previously uploaded this with logos but had to…
Add these decorative traction boards to your Traxxas TRX4 rig for some instant credibility. Look great printed in orange, but could be really cool in red too.
This is a replacement cover door for the standard traxxas TQ transmitter remote. Remixed from torula to have a flat bottom and sized correctly for my remote. The original was too long and too thick. Width was pretty spot on. It's in the…
Hi I made very simple wall mount for the traxxas transmitter. Enjoy!
Spare Tire Delete Plate for TRAXXAS TRX4 2021 Bronco
This is an extended battery mounting bracket, for the Traxxas Slash 4x4 LCG chassis. I designed it to work with my Turnigy Rapid 5500 mah 4S LiPo battery (as you can see in the pictures) Be aware that for this to fit the aforementioned…
Custom Front Wing and Rear Wing for Traxxas 2WD ONLY vehicles Provides adjustable downforce for speedruns! This is a pair of front and rear wings that have been designed to give adjustable amounts of downforce while producing very little…
conversion kit for the revo 3.3 & revo 2.5 found out it also works on the slayer pro.3.3 you will have to arrange the parts on your printer for best printing but al;l parts are printed with 100% infill hardware needed are standard revo…
My cousin got an XRT, and while it is the same frame/motor/etc it has a lower body than the X-Maxx so you need to V mount the fans it fits a 56mm motor and 40mm fans
needed a new nerf bar for my Slash RC car and drew one up with some additional strength and it seemed to work great.. now I just have a few on hand when we go driving
Mount for the Hobbywing Max10 SCT within a Traxxas Rally/Slash with a LCG chassis. There's a cutout for the temp sensor as well as it's pretty close. You'll need one M3x8mm and M3x12mm for mounting. The ESC and switch should friction…
I tried ESylin's drift wheel ( https://www.thingiverse.com/thing:1334558 ) and they worked great, just wanted some that are a closer diameter to the stock tires so I drew these up. This design is for use with 12mm hexes, which the Slash…
EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support…
Traxxas TRX-4M Zurrhaken / Tie Down https://makerteam.de/blog/projekt-traxxas-trx-4m-defender-umbau-tuning-3d-druck-pro-contra/
I created rails for the Traxxas Utility Trailer #9795 which fit relatively tight into the Trailer and can be taken off if need be.
These wings are meant for Traxxas 2WD models only. (NOT the rustler 4x4 or slash 4x4) Pls traxxas lawyers do not take this down again, this is a custom NON-TRAXXAS part.. Front wing installation: The front wing comes in two parts: the…
This is a custom mount for a Traxxas TRX4, designed for the ESS Dual sound module. It places the ESS above the motor for better weigh distribution than the provided stock mount. It fits a stock TRX4 with no modifications necessary. It…
I made a rack to hold my slash on a shelf that wasn't deep enough. wheels are off the ground.
this is the traxxas slash 1/10 scale battery adapter post. fits fine in the chassis. Print instructions Unassociated tags: r/c Category: R/C Vehicles
A battery holder for the Traxxas Slash. After having issues with the battery slipping out from under the my simplistic battery holder during jumps and flips, I created this one. Its wider profile means it holds the battery much more…
If you want to use Losi Mini-T springs on your Traxxas big bore shocks, for example p/n 2660, these spring perches will allow you to make the conversion (commonly used on 1/10 scale rock crawlers). This spring perch is designed to allow…
With intention to keep springs, wheels, shock absorber unloaded if car is not in use, I designed my own stand. Tested with Slash 1:10 2WD and 4WD, just check how far shall be mounted on place. Tip - you can lay aside your model even above…
I've created this roll bar from scratch based on models I saw online. It will fit the TRX4 sport body. Ease of print was in mind when creating this one so it is splitted in 2 parts and needs to be assembled together with M2 and/or M3…
a shock support and shield for the traxxas slash 1/10 scale 4x4 rc car. shorter than my other version which you can find here http://www.thingiverse.com/thing:1175692 Print instructions Unassociated tags: r/c, shock guard, shock support,…
1:10 Ladder, steps to the roof PLA, 210°C/60°C
Why? I didn't like the usual adapters that mount the ESC to the floor of the central chassis, because you always have to angle it upwards. In hard crashes it wobbled around. Additionally I needed the space in the central chassis pit to…
Stronger if printed on its side with supports. Gcode file is 50% infill. Files include with and without antenna tube mount. Note this was designed to fit with the VXL system. May not fit with the BL-2s system.
*New Update just up-loaded: 01-22-2025 “File name labeled with UPDATE-v2.” See file for further update details. **New Update just up-loaded: 02-01-2023 “File name labeled with UPDATE.” See file for further update details. ***Had to brace…
Slightly modified version of @Alex_Larie's Traxxas Slash Mud Guards.
Tyco / Taiyo Gears Turbo Hopper, Bandit, Twin Turbo, Fast Traxx I have designed various gears to fit some Tyco R/C & Taiyo R/C Vehicles. Each model has two different versions. One that is stock and one that accepts a bearing. I don't know…
Traxxas LaTrax part TRA7662 to replace the one that got lost. The official part: https://traxxas.com/products/parts/7662
This slips over the tires on a Traxxas Slash for drifting.
My cousin got himself a Traxxas XRT, and wanted more color on the truck so a few minutes in tinkercad, and there are blank, cutout, and labeled side crash/nerf bars for the XRT and X-MAXX(since they use the same bars/frame) I printed it…
Hello, I have a Kayak with a paddle 1:10 for Traxxas TRX 4 Defender . A very nice accessory for a 1:10 RC car. The kayak is fully authentic in 1:10 scale. Including oars, it even floats. Good luck with the printing! I used PLA/PETG as the…
Left and Right end parts to add that extra flare to the rear spoiler, remember all files are separate downloads. Thickness is 1/8" or 3.175mm More Models are coming, already have at least four more models just revising hole sizes as I…
This replaces the stock Traxxas Maxx (v2) battery latch system with a velcro strap system in order to use larger batteries. Just remove the two bolt on pieces and replace with these printed ones. Uses the stock screws for the front and…
Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. Uses same holes in chassis as Traxxas original ESC. I made it 3mm thick, cut it in your slicer depending on how thick you want it. Print Settings Printer Brand:…
I printed it in Nylon (Taulmann 645) and it works pretty well.
NOTICE!!! print in a strong filament like PETG,ABS or ASA. You can try PLA but I havent tested it yet and remember it is plastic not metal so be careful! if you have feedback please let me know and please tell me if you want the 39teeth…
Just a few simple spoiler(s) to go with the mount that was created. There are plenty of versions with a different arc to them. These are what I call High Mount versions, meaning the mounting holes are further forward making the spoiler…
the lower shock spring support for the suspension on the 1/10 scale traxxas slash. version with shield http://www.thingiverse.com/thing:1175692 Print instructions Unassociated tags: r/c Category: R/C Vehicles
This is a roof skid I made for my Traxxas Slash BL2s 2wd. I feel like I'm always flipping my Slash, so I wanted to make a skid for it like the Maxx, Rustler 4x4, or several other Traxxas vehicles. Since all of the Slash bodies are the…
Remix of mounting plate to allow new Max6 G2 variant to fit XRT with no chassis mods when using a 90mm motor (eg. 5690). Fitment is tight when using a 5690, a 4990 should work with additional room due to the smaller diameter. When…
This is an easy-to-print, easy-to-use one handed adapter for your Traxxas TQ or TQi transmitters. I recommend printing it with three wall loops and with 25% infill. Enjoy!!
This is the piece of the steering assembly that attaches to the servo on a 2WD Rustler. Compatibility: Traxxas Bandit Traxxas Drag Slash Traxxas Nitro Slash Traxxas Rustler 2wd Traxxas Slash 2wd
Sklopný držák mobilního telefonu pro vysílačku traxxas, u mě vozidlo defender TRX4. potřebný spojovací materiál: Čtverhrané matice se musí přímo zatisknout do stavěcích šroubů. edit 9.1.2025: přidán model stavěcích šroubů pro vložení…
I wanted to use velcro in my Traxxas Slash and Traxxas Rally with LCG. I designed it to use original screws and to be secured with double sided tape in the middle for extra strength. The double sided tape also helps to keep the distance…
These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. I have not attempted to print it yet, but the dimensions are the same. Print…
– Please Read This Before Printing – Printing filaments I recommend printing you tires in TPU filament, with more walls then usual and a Low infill (I would say max 10% ) For the WheelHub & the TireHolder, print them in PLA or any…
A very nice touch to the mustang body, it was getting a little outdated. I will probably have a few more designs coming out for it. Designs uploaded have been updated from the pictured product, updates include better screw hole placements…
This thing breaks all the time and I got tired of buying replacements, so I modeled this. It works fine, still breaks like the original. spoiler: I purchased metal ones because I got tired of printing replacements.
Traxxas Slash 2wd Dual spare tire holder. You will have to cut your body to make space for the wheels. The Slash spare tire holder bracket replaces the TRX5836 bracket. Model made in SolidWorks.
EDIT: updated with newer design a front bumper for the traxxas slash 1/10 scale 4x4 RC car. with 10 holes for LEDs this uses the mounts for the RPM aftermarket front bumper mount. Print instructions Unassociated tags: front bumper, LED…
Traxxas control arm Heavy Duty for Art.Nr.:TRX3655R Bigfoot Craniac HOSS 4x4 VXL Rustler Skully Slash 4x4 Stampede XO-1
1:10 Roof guard PLA 210°C/60°C
I 3D scanned the arm and made it a bit smoother. It's still a bit rough but it's fine for printing and using on your RC. Make sure to use support material on build plate only.
