Counting matching models…
As a kid growing up in the 80's, I looked forward to being grown up and having rooms full of stereo equipment and buttons, knobs, and blinky lights as far as I could stretch my imagination. Over the decades I outgrew that fantasy and…
These are an improved version of the wall mount brackets for a Vizio soundbar. These are based on the mounts that came with model SB36512 but will probably work for other models. The original brackets had an open back which dug into my…
A simple 10º angled stand for the Vizio SB2020N-J6 soundbar, it has a bumped corner to align the equipment's front side, I've added clear rubber pads on the bottom to prevent the stand from sliding. Printed on: PLA Infill: 15% Fil. Brand:…
A simple model that allows mounting of Vizio surround sound speakers to the wall at an angle. Mimics the included mount, but at a 45° offset. I found a couple of models online that were for this application, but they did not fit. So I…
I wanted to mount my rear speakers high up, but angle them downwards. This is a nice and sturdy mount that uses the existing mounting hardware that screws into the back of the speakers. Category: Electronics
This mount holds a Vizio Sound Bar under my TV stand to hide it out of sight. One version has holes, else use VHB tape. I printed it using PLA and did 3-4 walls and no top of bottom layers to expose the infill. When Using VHB tape, sand…
Wall Holder for the VIZIO - 5.1.2 M-Series Soundbar Remote. It uses double-sided mounting tape to hold to a wall. The bottom surface is also flat so you can use it to adhere to something else like a table or self. No supports are not…
This is a bracket to mount a Vizio 38" soundbar (model SB3820-C6) on a Vizio 55" TV (model M55-D0). The mount fits by friction into the vent on the back of the TV. There is a screw hole for the mounting screws on the soundbar. Maybe…
Recently purchased a Vizio soundbar/ subwoofer system and wanted to mount the soundbar to our 55" Vizio tv so that it would be directed at us when we move the tv away from the wall. Because the tv stand inserts are near the edge of our tv…
On the odd chance anyone else has a 50" Vizio TV and 36" Vizio Soundbar. Mounts using OEM leg holes and screws. Print instructions Print with Prusa Slicer defaults and supports everywhere. In Slicer place one onto print bed, place onto…
I added thin rubber to the bottom of the print, to keep it from sliding around
This aims to replace the crappy single screw wall mount that comes with these vizio sound bar/ surround sound kits. This wall mount allows for the cable to be slid in and out from behind the mount while it is attached to the wall. There…
Brackets to mount a Creative Stage Air speaker on a Vizio D24f-G1 TV using the feet mount holes when it is hung on the wall with a VESA mount. Includes retainer clips to hold the speaker from sliding out the end. To attach, mount one…
This is a very simple wall mount for a Vizio Voice Remote for a newer Vizio TV (V655M-K). I'm not sure if the remotes are the same for other models. I prefer to use Command Strips to avoid marking the walls so I didn't bother putting…
So this is just a remote holder for the vizio monitor. Print Settings Rafts: No Supports: No Resolution: .2mm Infill: 25 Filament brand: hathcbox Filament material: pla
So, after I put together our Vizio television a while ago, I was deeply disappointed at the lack of design integration for the sound bar. It either had to sit in front of the legs, or way behind, and the angle and spacing of the legs was…
Vizio Soundbar Wall Mount Bracket This is a simple wall-mount bracket for a Vizio 3.1/5.1 Soundbar, offset from the wall to allow easier access to the rear ports, and to allow for some cable management. This is compatible with the older…
Lost Vizio Satellite/Rear speaker mounts and screws? Don't want to put holes in your walls? This may be the solution to mount your speakers. Using generic M4 x 8mm screws with a built-in attached washer (see photos), and these prints, I…
This is a wall mounted Vizio TV remote holder. There is an inset on the wall side to place a command strip so the holder fits against the wall. I printed this at .4 layer height, 80mm/s, 10% infill. This holder is 90mm high by 60mm wide.…
Fairly straight forward setup, - Mount model labeled “Wall Mount” to the wall with the speaker RCA run through the channel (wall anchors are fine, speaker isn't heavy enough to necessitate going to a stud) - Mount model labeled “Speaker…
These parametric legs should work for any Vizio D series television, but was specifically designed for and tested on a 24" Vizio D24 whose mounting cavity is slightly smaller than other D series TVs. The f3d file is deigned to be…
This stand improves the angle of the sound towards the ears where it belongs.
I use this mount for my nightstand, and when I decided to upgrade to a multiboard, I needed to add a multiconnect backing. It's not pretty in the slightest. I may make it look nicer in the future, or if somebody wants to make a better…
This is imported from Thingiverse The (2018 model) Vizio P65-E1 TV I have is designed to blast sound off a wall and reproject back to you. Well, this doesn't work if you turn your TV away from a wall, and can be quite annoying if you are…
Remixed Model and added better wall support. Intended to use double sided mounting tape.
Mount for vizio 5.1 rear speakers. Needs m4x>10 for both speakers. slide in mount. Mount to wall with two screws. Discrete design.
This is a remixed holder for the Chromecast Remote Push-Click mount that accepts the standard Vizio remote. Original made by ByteSlinger It's a little longer, taller and wider, but still works with the other files in the original design
I remixed Shutz Vizio remote holder from the contest to also hold my switch for my hanging Havsris Ikea lamp. I'm not a mesh modeler generally but I am happy with how this came out. I printed it bottom down as it would be mounted. It took…
The soundbar sits about 12mm off from the wall, so it does angle down a bit. There's no rattling with heavy bass, however. Low profile version should make it more flush, but it is untested. I printed in TPU. It should work with hard…
I was always misplacing my TV remote and I wanted to give my remote a home, so I designed a wall plate that could hold the remote. This has mounting holes that fit a standard NEMA US electrical wall box. I've included 3 different sizes of…
I wanted to have a different mount for an old sound bar in my garage. This is what I came up with. It fits the VIZIO SB2920 sound bar. Printed at 0.2 layer height with 10% infill. It is plenty strong.
Wall mounts for the satellite speakers that come with the Vizio V51-H6 5.1 surround system . They angle the speakers off the wall by about 17 degrees (on the XY plane... so horizontally) so that you can plug in the cord while the speaker…
This a low profile mount I designed to mount my Vizio M51 (M51a-H6) Soundbar underneath my new mantle I recently finished. Print TWO pieces. Fit, position, and measure - IDEALLY these should be positioned centered to the 2 recessed areas…
Remote control for Vizio TV
Just a nice base for my VIZIO SPEAKERS, I will post a new pic once I installed with all wiring.
remote control stand for vizio tv
So, after I put together our Vizio television a while ago, I was deeply disappointed at the lack of design integration for the sound bar. It either had to sit in front of the legs, or way behind, and the angle and spacing of the legs was…
This mount is designed to securely hold the rear satellite speakers from a Vizio M512a-H6 surround sound system while keeping a low profile against the wall. It may also fit other speakers with similar mounting geometry, but only this…
Wall mount for a vizio V21t-J8 soundbar. I bought one used and it didnt come with the wall mounts. Instead of ordering replacement I designed these and was able to mount it with no issues. It has the mounting holes in the bottom and also…
Simple stand for a Vizio Sound Bar. It raises it up 25 mm to give clearance for Wii Light Bar and TV stand feet. I designed this to fit the VIZIO SB3621n-E8C in my living room. But it should work for any sound bar that has 50mm x 50mm…
I needed l ow p rofile f eet for fitting the TV in a kitchen cabinet. I'm not sure if this will fit other Vizio TVs , but it might . I made some additional mounting holes in the feet for screwing down, as there is no support to keep it…
Replacement TV leg for Vizio TV. The numbers on the leg are P34T2335 and XLC01C0100 for a circa 2015 model. Three options Original 30 degree offset Straight Just the connector to add to your own print I printed upright with supports to…
Simple remote holder for my Vizio remote. Will likely fit others. Has two mounting holes to use screws for mounting or use a piece of double sided tape on the back.
This mount is designed to securely hold the rear satellite speakers from a Vizio M512a-H6 surround sound system while keeping a low profile against the wall. It may also fit other speakers with similar mounting geometry, but only this…
Large Flatside Down is how i printed with small supports on either side. Enjoy!
I printed this model with a Prusa MK3S and PETG filament at 15% infill. It is easily mountable to the wall using double-sided tape.
Vizio Sound Bar Bracket For TV. I have a Sharp TV and a Visio 32" SB3220n-f6 sound bar. The feet are if you want extra support on the bottom. Used for wall mounted tv setups. If your like this model consider buying me a coffee?…
Part to mount my Vizio SB3621nb-G8 Soundbar to the bottom of my 32in Vizio E32h-C1 TV via the original leg holes. Print on its side, with the part which will fasten to the soundbar upright, No supports required. Used original leg screws…
I needed a removable way to mount my Kinect to a Vizio M322i display. This is it. Attach it to the bottom of the Kinect with a ⅜" bolt, and set it atop the set…good to go. Requires no supports. Print Settings Printer Brand: MakerBot…
Simple holder for an older style Vizio TV remote. Has the hex mount built-in, no need for additional attachment parts. Printed well with tree support only on the back where the attachment hex is located, the front design part will print…
Cover for rear speaker of Vizio SB3651-E6 5.1 Soundbar that redirects sound to the side. In my room one rear speaker was in a corner, and therefore sounded much louder that the speaker that was in the middle of a wall, so this redirects…
Here is a stand mount for a Visio rear speaker form the SB46514-F6 speaker system. It prints in 2 perices that you screw together. It may fit other Visio speakers but check the dimensions. Additional parts 3 x M3 screws 10 - 16 mm long 1…
About I have this neat c-table with storage that's perfect for a remote. However, it would often fall inside the storage tray. While it's not a big deal- why not solve that problem with 3D printing?! :) This remote holder was mainly…
This spacer works with this Vizio Sound Bar Mounting Bracket so the soundbar does not have any room to wiggle while it's resting in the slot. It also lets the soundbar be lifted off the bracket with ease. Works with Vizio SB2920-C6
Need a wall holder for my Vizio XRT122 universal remote, so my kids would stop losing it. Printer Settings: 0.4 nozzle, 0.20mm with 4 walls (but doesn't really matter)
While I was cleaning up my garage I found the feet for my cheap TV that I have hung over my monitors and realized I could move my webcam off my monitors and up to the TV instead. Took the calipers to the foot and recreated it, shot a 3"…
needs supports probably .2 mm layer height i printed with the hollow end face down
We bought this Vizio sound bar a few months ago and our cats would turn the speakers and it was rather annoying to look at, I initially made some brackets to help that slipped over the original mounts but the wall they mount to is shared…
My toddler kept pushing and tipping the soundbar, so I designed this bracket to hold it in place. Simply print two copies of this bracket, use the soundbar's included screws to attach them, and use your favorite double-sided tape (like 3M…
Used 3 walls with 15% infill, .2 layer <<<These settings worked just fine for me. Download and Print my model to make your TV fit where it wouldnt before.
