Counting matching models…
Made this for my drink mixer project to weigh the content added to a glass. I have the autocad file if anyone needs any changes to the scale or bottom. And if you liked my project please consider just tipping me for the fun of it. Print…
97x71 version of the original project
Nests in drawer indentations and has a chamfered base to easily grab small parts from the bottom. I
Adapted and more holes placed in top plate to make room for a 4-pin header coming from the HX711 of the Smart Bed occupancy sensor by Lukáš Porubcan . Category: DIY
Simple enclosure for HX711 load cells weight display module. I have several weight scales and i connect the module using 4 pole phone jack + cable. It contains also space for 18650 battery and charging circuit. Used parts : weight display…
I made this enclosure so I can build a bee hive scale with four HX711 load cells on each corner. It's made to be used outside and can be sealed with a fitting o-ring. Also it's supposed to be screwed to a top and bottom frame, so that the…
Filament holder with scale compatible with the Filler system. https://www.printables.com/de/model/174620-filler-filament-holder Built in is a load cell for 3kg with HX711 module. !!! The diameter of the filament roll must be larger than…
Board clips in. Uses M3 screws to secure it. No supports needed. Be careful sliding the board in so the front fingers don't hit the PCB components. If top side tabs are too tight, trim them with a knife or side cutters. It's for the…
This is a scale case for a 5kg scale Module and the HX711 pcb. It can be connected to a RaspberryPI and used by the Octoprint Plugin “Filament Scale Enhanced” ( https://plugins.octoprint.org/plugins/filament_scale/ ) The filament spool…
Test bracket for HX711 bar-type weight sensor.
HX711 load cell display module box with battery and charging module. Assembly Notes/etc: The cover interferes with the charging board, just cut the lip away where it touches. It was easier to modify than measure and place in CAD for a one…
Lost my Full size PCI Bracket for my Intel X710-T2L so I made my own! I created the same bracket back when I had the Intel X540 but it looked horrible in BambuStudio so I had to recreate it with the skills I've acquired since then. This…
I'll need a touch protection for the electronic component nearby a load cell. On picture 2 you can see this was made for the pcb with the red frame. But this pcb didn't work for my project. So I used the other one. If you have the same…
I made this to house my HX711 boards along with my breadboard. Uploading in case somebody else finds it useful! Everything uses M2 screws and the center fits a 2.54mm pitch breadboard with 7x8 holes. There are indentations on the back…
Needed new base to get the proper angle for my GX71 mirrors for my MX73 Toyota Cressida. Might require a little sanding to get a perfect install, but is a great starting point.
Description: Build your own connected smart scale with this 3D printable enclosure! This design provides a robust and clean housing for the essential electronics, allowing you to create a WiFi-enabled scale that can send weight data to…
Simple enclosure for basic HX711 ADC modules, specifically the ones linked below. The lid won't fit with the included header pins so to use it you will need to use right-angle header pins or solder the wires directly to the board. I…
This is the 3D model for a PCB I designed to connect a D1 Mini and an HX711 together with 4 load cells to create a scale or occupancy sensor. Case is designed to use a single m4x10 bolt and m4 nut. There are no traces that go to the hole…
Thermaltake Core X71 Case Front Cover - Cover for the front drive bays Summary: Needed a quick and dirty way to cover the front of this case. Able to match the pattern pretty well. I don't have to look at it all the time so works for me.…
A cover for the wires of a HX711 load cell based set of scales used as a keg scale for Cornelius kegs and mini-kegs. This is inspired by the instructables post https://www.instructables.com/Beer-Keg-Scales/ The hx711 and related circuit…
Použil jsem držák váhy s těchto stránek a upravil jsem ho pro držáky Endr a podobné. Duležité: podívejte se jaký typ siloměru požívám, díra - M4 , rozdíl bývá dírách je buď M4-M5, pokud máte siloměr s dírou M5 použité držák pro siloměr ze…
I created this to support 3kg spool but the platform can be adapted to any other content.
Blinddeckel für Steckdose 71x71x13mm
This is a dual 50 KG load cell and associated HX711 amplifier holder. I'm using it to detect the presence in the bed of a handicapped relative. My intention is to use the setup to trigger a Zigbee door switch or leak detector so I can…
The cable for the PSU is not very long and is bulky. I wanted a means to mount the PSU to INBXX instead of the Core One. This mod is for the US version, but the EU version can be made using the included 3mf project file if needed. I also…
Hold 2 Spools up to 5 kg and measure the weight of each spool seperate. You need 2 HX711 Sensors with 2 Boards and a MH-ET Live board. Software for the MH-ET Live is currently ESPHome to gather the data to HomeAssistant and calcualte…
case for holding hx711 and arduino pro micro
Quick & dirty model for an under desk clamp to mount the power unit of an Ugreen NAS (dxp4800). Fits 4,5 mm Wood-Screws with counter-sunk head. 0,28mm (draft), 3Perimeter, 15% Infill. PLA is fine if you are gentle when tightening the…
The Ruckus C12P, which is an excellent switch, has a known problem with power supplies breaking down (usually due to heat and inferior components). Since I didn't want to replace the bad power supply with another bad one, I took the…
2 per speaker, 75mm diameter, probably best to add some double sided tape to reduce vibrations
Print with PETG. Meant to go through the slot behind the front cover. Use a shallow connector like the JST PH 2.54mm on the board side.
Remix for the 5300 series (HX710B). It fits tightly so that it does not rattle. Printed on Bambulab A1 with PETG. 0.2mm layer height with 0.4 nozzle.
