23 models
This is a simple replacement hinge for the Sony WH-1000XM5 headphones, that comes in handy, when your hinge breaks. Note, that this part is for the RIGHT hinge, If your left hinge is broken, just mirror the ‘Earpiece (Meshed)’ Part before…
One of the arms on my Sony WH-1000XM5 headphones snapped. This print clamps over the arm, using 3 M3 nuts, and 3 M3 8mm cap screws to hold it together. The arm on mine broke with conveniently ragged edges, so alignment was very easy. I…
You will need a screw where the thread is M3 and 8mm long and an M3 nuts. You will need to push the wires through the gap in the print and the make sure the thicker part (bottom) is clamping onto the bearing and the slimmer part is…
This part provides an encapsulating brace for the pivot hinge for the Sony WH-1000XM5 noise canceling headphones. The brace is tight enough around the bottom part to keep the joint together while remaining loose enough around the pivot to…
https://www.printables.com/model/503765-sony-wh-1000xm5-hanger This is a remix of the above model. I added 3 hangers that hook into the slots of the front panel for the Fractal North. I have not tested with the XL north case. Headphones…
To hang your headphones from the wall, bedside table etc with the help of double sided tape. Scuff the surface your taping for better adhesion before mounting. Two models, one with text and one without.
my own designed fujifilm xm5 handgrip, you can use ¼" for the 3 thread inserts
This is a simple replacement hinge for the Sony WH-1000XM5 headphones, that comes in handy, when your hinge breaks. Note, that this part is for the RIGHT hinge, If your left hinge is broken, just mirror the Earpiece part/ To install it,…
The wall mont is attached with two screws. The holes each have a diameter of 5 millimeters Print settings: PLA 0,4 mm nozzle 0,15 mm layer need supports
This simple yet elegant mount for Sony WH-1000XM5 headphones is designed to be mounted under the desk, freeing up valuable space on your workspace. It provides a secure storage solution for your headphones. Features: Sleek Design: The…
This design places a Qi receiver inside of a 3d printed cover for the right earphone. Note that this prevents access to the touch controls. A matching left ear cover can be provided to make the two sides match. The headphones charge by…
As there was no WH-1000MX5 stand, I designed one myself. I wanted it to be printable at once. If you print it, you may want to use the “custom support material” stl file in the downloads. Otherwise Prusaslicer will generate a lot of…
Adapter to fit the ModMic Microphone to the Sony XM5 using the 3.5mm jack on the headphone. Prints well at 0.15mm height without any support (other that the support build into the model.) Use the magnet from the standard ModMic adapter…
Slim inlay for the cable-compartment of the Sony WH-1000XM5 case. Can be fixed with some double-sided tape if neccessary.
The original headband frame of the Sony WH-1000XM5 is too narrow, causing concentrated pressure on the top of the head and discomfort during long sessions. These adapters clip onto the existing hinge housings with a snap-fit that requires…
This is inteded to hold Sony WH-1000XM5's and be screwed to the bottom of a desk ideally on the edge for easy access.
Print with an high infill, 5/10 walls and 1.5 bottom and top thickness, pla should be fine.
Designed so that no supports are needed. Model with cutouts makes the fixture screws more accessible during installation, the "whole" model is more finicky for screwing it in place.
Makes sure the headphones are always perfectly centered on the wireless charging pad
One of the arms on my Sony WH-1000XM5 headphones snapped. This print clamps over the arm, using 3 M3 nuts, and 3 M3 8mm cap screws to hold it together. The arm on mine broke with conveniently ragged edges, so alignment was very easy. I…
ZenDock for WH-1000XM5 – Minimalist Magnetic Charging Dock Elevate your headphone experience with the ZenDock for WH-1000XM5, a sleek, minimalist docking station designed exclusively for Sony’s WH-1000XM5 headphones. This design marries…
I modeled it for myself. There are 2 version (with and without a loop to hook airtag etc.) I used a drop of hot glue to fix the earbuds casing to the printed case. Airtag case from the pictures is a different model (not mine.) and not…
20% infill gyroid. It works very well, tbh took 15 min to design. ig: @kossler_photo
