Counting matching models…
Includes a recessed holder for Zooz ZEN34 ZWave Decora remote with or without magnets. Good for smart light or scene control. Personal use case is on bedroom night stand to control smart lamps, fans, run goodnight routines, etc. Magnets I…
Remix: You will need the bottom from the original case. It's essentially identical to the original case, but with an extra 8mm of clearance in the top shell. The original case would've fit with the ZAC93 or the Pi cooler, but to fit both…
This holder will allow you to use the metal clip that you find on most standard garage door opener fobs to hold a Zooz ZEN34 z-wave switch to your car's sun visor. You can associate the switch with e.g. the Zooz ZEN17 universal relay…
Compatible with Zooz 700 Series Z-Wave Plus Open/Close Sensor ZSE41 for Door, Window, and Gate Monitoring …instead of using the double-stick tape to mount it, this mount requires two screws, and allows the sensor body to be slid up or the…
A mount to allow attaching a ZSE40 to the edge of a 6mm shelf.
Updated bracket to deflect rain/snow away from the sensor. You can use the original adhesive or a nail/screw to attach to your fence gate or whatever. PLA and PETG print fine, but consider the color and location if it will be in direct…
Uses M3 x 12 SHCS screws and captured nuts to mount the ZSE11 to the mount. Uses drywall or similar screws to mount to the wall. Specifically designed for Zooz Z-Wave Plus Q Sensor ZSE11 | Motion, Temperature, Humidity, Light Sensor…
This is a wall backplate for the charge station of a ZooZee robot vacuum. This backplate will offset your charging station from the wall, in case your wall is uneven or you want to run wiring behind it. The offset has a clearance of 15 mm.
Enclosure for Zooz dimmer to neaten up all the wires, and reduce the fire hazard in my plenum space. I also made an RGBW tape endcap and a dupont crimp terminal cover for this project, linked below. Dupont Crimp Cover…
This is a custom-designed wall/surface mount for the Zooz ZEN58 XS Relay , allowing for a clean, secure, and accessible installation. The relay snaps firmly into place using dual retention clips, combined with a snug friction fit along…
This mount for the Zooz ZSE41 contact sensor snaps onto a 20mm x 20mm metal bar. The metal bar may move up and down, thus, the magnet and contact sensor cannot be fixed on the structures. The bar will move down by 4" on occasion which…
This model was created to allow the Zooz ZSE41 Open-Close XS Sensor to be mounted using screws instead of sticky adhesive tape. It also fits the holes left behind from a SecurityMan alarm installation. This model was printed with PETG.…
Add Z-Wave environmental monitoring to your Prusa USS Drybox using the ZOOZ ZSE44 Temperature/Humidity Sensor. This mount securely holds the ZSE44 and slides directly into the existing hygrometer slots inside the Prusa USS Drybox. *****…
It's orientated for no supports, but if your z-axis is a little wobbly may want to lay her flat and do organic supports for the front lips.
Updated bracket to deflect rain/snow away from the sensor. You can use the original adhesive or a nail/screw to attach to your fence gate or whatever. PLA and PETG print fine, but consider the color and location if it will be in direct…
Simple cover to hide wires and some inline resisters on those wires connected to a Zen16 Z-Wave relay.
While the Zooz ZSE70 is a very nice Z-Wave LR outdoor motion detector, one issue I have with it is the thin back can be difficult to unscrew to change batteries or access the “Z-Wave button”. I designed this simple wrench to take care of…
This is a custom-designed wall/surface mount for the Zooz ZEN58 XS Relay , allowing for a clean, secure, and accessible installation. The relay snaps firmly into place using dual retention clips, combined with a snug friction fit along…
I bought a ZEN37 Scene Controller but I wanted to have it mounted on the side of my beside table versus the provided in-wall mount. I designed this button holder to securely hold the scene controller for regular use but allow it to be…
Are you also bothered by how much the Zooz remote switch protrudes from the front of your wall plates? This spacer brings the wall plate flush to the remote switch. It replaces the existing base and is friction-fit to the remote switch,…
I got sick of changing the battery in my Zooz ZSE44 Temperature Humidity Sensor, so I replaced the coin cell holder with a 2-AA battery holder and made this case to hold everything together. The circuit board is just glued to the original…
I needed to mount the Zooz Zen25 double plug under a desk, so I made this thing.
It's orientated for no supports, but if your z-axis is a little wobbly may want to lay her flat and do organic supports for the front lips.
One of my sensors is too far away from the controller to allow for successful firmware updates, even though it works great in normal operation. Since the board is mounted to the part that is adhered to the door/frame, it doesn't support…
This is a Gridfinity-compatible holder designed for a Zooz ZEN37 wall remote, but should work with any Decora-style wireless remote. It's 1U wide x 2U long x 3U high, and comes in two variations: with and without the stacking lip.
Simple cover to hide wires and some inline resisters on those wires connected to a Zen16 Z-Wave relay.
While the Zooz ZSE70 is a very nice Z-Wave LR outdoor motion detector, one issue I have with it is the thin back can be difficult to unscrew to change batteries or access the “Z-Wave button”. I designed this simple wrench to take care of…
Case to wall mount a Zooz 800 Series Z-Wave Long Range USB Stick, ZST39 LR.
I love the Zooz ZEN37 Wall Remote scene controllers for controlling WLED lights... but I didn't love that they felt a little small and a little fragile for my young kids to use. So, I designed this case. The case gives the controller a…
This sensor has been sitting on my toilet for 2 years, and is constantly being moved by a toddler. It was time to put it out of reach on the wall.
Holds the sensor at 30 degrees below horizontal. Fits a ~19 mm piece of wood or other object. Print with the protrusions facing up; no support should be needed.
I have tile floors in my bathroom and when the ZSE42 sensor is on the floor and someone takes a hot shower, the condensation on the tile trips the sensor. I made a small bracket that lifts it off the floor slightly so that it will only…
This mounting bracket was made specifically for the Zooz ZSE40 z-wave 4-in-1 sensor. This allows the sensor to be placed in the following positions: Sitting on a shelf pointing upward at 45 degrees Sitting on a shelf pointing sideways…
Replacement clamp designed specifically for display on ZOOZ e-bikes. Stronger than the original design. Recommend using ABS or Nylon.
This is a model of the bracket that holds the display on a Zooz e-bike. Not as sturdy as the real replacement, but I broke mine in a crash and wanted to get back on the road ASAP. Push the metal pin on the stock unit out with a small…
Please comment, rate, and post a make! I'm using the Zooz ZST10 stick with Home Assistant. Stick works well, but I'm a full wave kinda guy and wanted to replace the little coil antenna. So, I desoldered the coil, soldered on a UFL…
Background ZOOZ electric bikes have a stem with an integrated LED headlight. This in itself isn't problematic however in order to aim the light towards the ground in a usable manner, the stem is shaped in such a way that if the bars are…
Our Zooz 4-in-1 Sensor was mounted on the wall at an angle using double-sided tape. When I removed it for painting I didn't have any more double-sided tape laying around but I did have a bunch of suitable screws on hand. Problem is, I…
I needed to mount a Zooz ZEN34 wireless switch in a metal Raco electrical box. The original mount didn't fit the Raco cover and I didn't want to cut it, so I designed this mount. I glued a pair of 18mm dia. magnets onto the back of the…
This is a table stand for a Zooz ZSE44 Z-Wave Plus 700 Series XS Temperature and Humidity Sensor with Mounting Bracket (purchased separately). The ZSE44 sensor snaps into the mounting bracket and that assembly then snaps into the table…
