Counting matching models…
This model barely fit in the mk3 bed size, and may be a bit flexible but having support under helped You will need 6 8mm m3 screw and 6 m3 square nuts to bolt the part together. The switch is meant to slide from the front, and be locked…
I couldn't find any other designs that could fit this switch so I made my own. This design is for the v2 version that has 3 holes in a triangle pattern. The v3 chassis of the switch has 4 holes and looks slightly different. Check the…
Template for mounting plate for ZyXEL routers: [NWA50AX] https://www.zyxel.com/global/en/products/wireless/80211ax-wifi-6-dual-radio-poe-access-point-nwa50ax [NWA90AX]…
I just started playing around with Fusion 360 yesterday and created brackets for my 10" Rackmount.
Printend at 45° angle so it fits the printbed. 0,2 layer height, 20% infill, PLA The switch sits really snug, no other mounting needed
I lost my brackets for mouting this switch in a rack, so I made my own since the other on Thingiverse didn't fit my holes. Use M3 8mm to mount them in the Switch. Print instructions Print Settings Printer Brand: Prusa Printer: i3 MK3…
Die Winkel ermöglichen die Montage von Zyxel GS1100-16 V3 Netzwerkswitches in 10 Zoll Netzwerkschränken.
Rotate it…. or you will need supports. :) Printed mine in PLA.
This model contains three variants of the rack mounting ears for the Zyxel GS1900-24E. First is the original, which matches the metal ears provided by Zyxel, and is likely too flimsy for 3D printing in plastic. There is a reinforced…
Print the main bracket strong. Other than that, have fun and choose a nice color!
This is a simple stand to use the Zyxel NR7302 indoors. It might also be compatible with the NR7301 and NR7303, but this is untested. To mount the Zyxel NR7302 to the stand you need 4 M4x15-20 screws.
Zyxel GS1200-8 10 inch rack mount, remixed from the excellent model by Chillora. The remix introduces rounded corners and a centered slot to match the “rounded” rack look. Recommended to print in PETG for high thermal environments with…
The backstory: Tasked with the challenge of mounting a compact 5-port switch in our attic to facilitate network connectivity for our office outlet and Wi-Fi access points, I found myself with a Zyxel GS-105B at my disposal. With little…
I created this to mount my Zyxel MG-108 switch in a 10 inch rack. This switch is tricky to fit in the rack as the switch is longer than 10 inches, so I created an open slot on the side to slide it in. This will NOT fit in your rack if you…
Rack Mount Ears (19" Inch) for the Zyxel 400 Voip Gateway I created this Rack mount Ears for the Voip Gateway 400 delivered by Telekom Germany. Fitted perfectly to our Rack. Print instructions For Printing just import the STL to you…
Wall mount for Zyxel NWA5120 and NWA1123 Series WLAN Access Points
Zyxel Cloud WiFi6 AX1800 halter für Tisch
Tipp: genug Infill wählen - (35% Gyroid reicht aus)
A wall mount for a ZyXEL modem designed in Fusion 360. This is my first try at making my own model. No supports are needed, printed on Ender 3 v2 with .5mm nozzle and .25mm layer height. Printed in black PLA MAX from Hatchbox. Screw holes…
Adhesive assembly required. .step included. Remix If you want to use it as a template for your own mount, try looking at https://www.printables.com/model/341266-step-zyxel-nwa50ax-nwa90ax-nwa110ax-mount-plate-te Slicing guide: Enable…
There are already a few 10 inch rack mounts for Zyxel GS1200-8 (and GS1200-5), but this one has some unique features: As slim as possible, to squeeze it into small spots. The holes fit between the 0.625 inch and 0.500 inch sections…
1U Rackmount for Zyxel XGS1250-12. Split design for small printers. BOM: 14x M2 heat-inserts 8x M2x25 (or longer) SHCS Screws 2x M2x16 (or longer) SHCS Screws 4x M2x10 (or M2x12) SHCS Screws You'll find a full assembly which shows how to…
кронштейн (подвесная полка) для роутера Zyxel Keenetic GIGA
Wall mount for the Zyxel WAX510D Wireless Access Point, with catch. Printed in Bambu Lab PA12 GF
This is a mount for the Zyxel GS1200-5HPv2 network switch so it can be mounted in a 10 inch rack. The mount is 1U high, and the switch mounts flush with the front. The total depth when mounted in the rack is no more than then depth of the…
Nederlands (Dutch) Ons nieuwe modem paste niet in de kast waar deze moet worden geplaatst, dus heb ik deze kortere versie van de muurbeugel gemaakt. Je hebt misschien carrosserieringen achter het beugeltje nodig zodat het modem recht…
The standard Zyxel T-56 modem/router by the Dutch internet provider Odido is poorly designed when you don't want to put it on a table. If you want to mount it to a wall the cables can't be plugged in and/or the power button is…
This is a custom 19" rack mount designed for the Zyxel GS1900-8HP switch . It features left and right mounting brackets , each split into two parts , ensuring a secure and ventilated installation. The design includes ventilation holes and…
Rackmount for the Zyxel XMG-105HP switch with honeycomb pattern for ventilation. Print in PETG or ASA/ABS, quite tight tolerances.
Einfache Wandhalterung für altes ZyXel GS-108B 8-fach Router, Innenabmessung 156 mm breit, 28mm tief, 86 mm hoch. Links und rechts jeweils eine Lasche mit 4mm Bohrungen für Schraubmontage. Gedruckt mit PLA, 7 bis 8 Perimeter, damit die…
Extended the right part (part1) by 54mm
I wanted to have a Switch in my 10" Server rack, and this one was the perfect size, tho it only came with 19" rack mounts. This model uses the original screwholes & screws to fasten, and can be easily installed in your cozy home 10" rack
A holder to mount a ZyXEL switch onto a Skadis board. To mount the holder to the peg board, use these T-nuts .
Uchwyt montażowy do przełącznika internetowego model GS1100-16 Zalecam drukowanie z dużym wypełnieniem i użycie mocniejszego materiału.
Specifically made for the Zyxel XMG-108HP, but should also be useful for other switches with similair size: Width: 240 mm Depth: 105 mm Height: 27 mm This switch can get hot, so make sure you print it with material that can handle it. It…
Mount Zyxel GS1200-5HP v2 in 19inch Rack
LTE Indoor Router - Zyxel LTE3301-PLUS The Router has mounting holes on left and right and manufacturer do not sell mounting brackets for it. I wanted to mount it on vertical space - so i designed little brackets for it. You only need to…
Wall mount for the Zyxel WAX650s, with catch. Reserved engineered from orignal mount Printed in Bambu Lab PA12 GF.
I really liked the original ESRack system design created by @EvilProphet . I created a module for Zyxel Switch GS1200-8 from the ESRack Customizable Device Mount by @DavidKahler_64887 The ESRack system includes the following components:…
A generic 10 inch 1U Rackmount for the Zyxel GS1200-8 i bought for my Lab Rax. Locks the switch in place without requiring screws, allowing it to be mounted in virtually any orientation. Upside-down, hanging in a rack or standard vertical…
A mounting system for IKEA Skadis pegboard and a Zyxel XMG-108hp POE switch. switch dimensions are 240mm x 105mm x 27mm Designed for vertical mounting and reversible. Just mount bottom cap, insert switch then use top cap to lock into…
My modem was on the ground and I just want to wallmount it and there was no wallmount holes in the back of modem and I created this model to improve cable management.
Zyxel VMG4005 \ Cetin Terminator wall holder
Mount for any 1U Zyzel USG device to stay upright without falling over Raises the device off the bottom to allow for additional airflow Screw-in and cable tie holes allow for an even more secure mount to the shelf Suggest printing in PETG…
Consider this v0.9, there are some quirks that can be fixed, but I'm pretty happy with this version. The indicator lights are behind the rack legs, so a bit annoying to check The top of the rackmount can be solid to have a bit more…
Thanks to @Vaarlion_340250 for the Original Model.
The 3D files are those of an improved version than the one on the image. I have not tested it.
Brackets for the Zyxel XMG108(HP) for mounting them in a Standard 10 Inch Rack (I use a Digitus one), as the only one i found needed about three times as much filament and didnt fit Racks with L-Shaped Mounting Bars. I printed it without…
The full gimbal can print as one. Or separately for each filament color. Scaling not tested but there is room for it. Default print settings work fine (15% infill, no support needed). The handheld base includes two orthogonal groves, you…
Is your Zyxel XMG-108 2.5GbE Switch cluttering your desk? This simple yet effective mounting solution allows you to secure your switch to a wall, under a desk, or inside a cabinet. The brackets are designed for a snug fit, ensuring the…
This uses the multiboard interface and is part of the underware ecosystem, made for opengrid primarily
1U 19'' Rack Mount for Zyxel GS1200-8HP Managed Switch and its Powersupply
I needed something that can fit both network devices so i combined them :)
Für den Zyxel GS1915 Switch habe ich eine waagerechte Wandhalterung gemacht.
Multiboard mount for a Zyxel GS1200-5HPv2 5 port managed POE switch. Parts for both the switch and the power supply. You will need to print two of each. Printing Guidelines: I printed using standard Multiboard settings. Use 3 perimeter…
This is a mount for the Zyxel GS1200-5HPv2 network switch so it can be mounted in a 19 inch rack.
Fits: Zyxel GS1200-8 — 155 × 85 × 26 mm. Print settings Print it face down — front panel flat on the bed, tray pointing up. This is the one thing that matters. Printed upright, the top edge of the cut-out becomes a 157 mm unsupported…
This small accessory can be used as distantion hanger for Zyxel modem sold by O2 for VDSL internet. It provides enough space for cables heading to the wall. Distance between modem mount sockets is 11cm. Hang by 2 wall screws
Zyxel Keenetic ULTRA 2 repair
the "switch bracket halter" is the model for the back of the switch, without the screw holes, "switch bracket" is for the front of the switch with the holes Printed with PETG, 20% Infill Orientation of the print depens on how you want to…
Support stand for the Switch Zyxel (GS-108B v3) use countersunk screw M4 x 15 to hold the switch. M5 screw to fix the stend.
Added a wider screw hole as my screws were larger than the original
Wall mount for the Zyxel PM5100-T1 ONT and similar with an internal compartment to store the excess fiber optic patch cord. ISP-supplied patch cords are usually much longer than needed when the ONT sits next to the optical termination…
My Zyxel switch took too much room laying flat and I didn't want to put it on the wall, so I designed a basic stand. The switch is fixed with two flanged headed screws (screwed directly into the plastic, leaving a gap between the head and…
No hardware cover for the BE5100 and BE6500 access points by Zyxel. It is held in place with pins that extend into the screw recesses I printed mine in PLA with the top PIN SIDE on the plate and internal organic supports. The cutout is to…
Overview (English) This adapter mounts a Zyxel XMG1915-10E horizontally on an original IKEA SKÅDIS pegboard. The switch uses its factory keyhole mounting slots, so it can be installed with the network ports facing down , matching the…
Consider this v0.9, there are some quirks that can be fixed, but I'm pretty happy with this version. The indicator lights are behind the rack legs, so a bit annoying to check The top of the rackmount can be solid to have a bit more…
Thanks to @Vaarlion_340250 for the Original Model.
No hardware cover for the BE5100 and BE6500 access points by Zyxel. It is held in place with pins that extend into the screw recesses I printed mine in PLA with the top PIN SIDE on the plate and internal organic supports. The cutout is to…
Wall mount for Zyxel NWA5120 and NWA1123 Series WLAN Access Points
supports on the build plate. PETG, 20% infill is fine. Needs assembly, 6 screws and square nuts M3x8
Support pour ne pas gêner la sortie d'air de la Livebox dans ma baie de brassage. Support so as not to obstruct the air outlet of the Livebox
Model 1U Zyxel halter contains 2 Volumes. Separate them and print them in a way displayed in the provided print files. You have to glue the parts together before use. It enables modifikation for other desktop switches and easier print.
