Federal Signal 2T22 Siren (Fully Functional)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Mechanical Parts
- Licencja
- Creative Commons — Public Domain
This is a functional 2t22 siren model with Dual Tone! It works with two DC 130 motors. Please excuse me for having two motors and covering them with a motor cover. This is not the case with the original 2t22, but I wanted to design the model so that no special hardware is required and as few parts as possible need to be ordered or organized. The model should not be difficult to print.Actually, I wanted to make a 3T22 WITH solenoid valves, but because of the size of the model, I didn't want to add them. AR-Timer and Photos of Pole mounting comming soon!
Parts Required
- 2X DC Motor
- A little bit of cable. (Depending on how you want to set up or use the siren)
- Super Glue
- Screws (If you want to mount the Siren on a pole.
Printer Settings / Filament Instruction
My best recommendation would be to use a more flexible material for the horns and normal filament for the chopper, stator, and other parts. For maximum stability, you should use ABS. I used PLA, but as long as the model is not exposed to sunlight, PLA should also be possible. I mounted my model on a mast even though I actually printed it with PLA.
Infill: 15-20%
Printer Speed: 100% (Bambulab and other)
Supports: Yes (Chopper, Stator, Hat)
Brim: No
Wall generation: Arachne (For Horns only)
wall thickness: 0.21 millimeters (For horns only)
I think thats all :)
How to Build
ATTENTION! Before assembling, make sure you have printed out all the parts!
Check here to see if you have all the parts:
- 22X Horn
- 1X 10 Port Chopper
- 1X 12 Port Chopper
- 1X 12 Port Stator
- 1X 10 Port Stator
- 1X Intake botton
- 1X Intake Top
- 1X Hat
- Montuing Hardware (If you mount on a Pole.)
First, you need to glue the motor to the stator and connect it to the chopper. Important! There are choppers and stators. The 10-port and the 12-port. The 10-port goes at the end and the 12-port goes at the top. Once you have connected the two motors to the two stators/choppers. Now you can connect the cables and then place the motor cover over the two motors. Next, you can attach the two intakes to the stators. Now you can put the hat on top and attach the desired bracket. Now you can run the siren with 3-6 volts.
Mounting and Controlling
You can Mount the siren with the Stands on the Files > Stands. I upload Soon photos of my mounting on the Pole. Next week i upload a AR-Timer for controlling the siren. And by the way: I'm not the world's best designer. I have experience, but I'm still not a specialist! If you see a mistake in the model, please let me know so I can correct it. All my siren designs have been tested and they work. You must glue the stand in place, otherwise it won't be stable enough and may be a little too big. Create a Hi-Lo with your hands!
WARNING! The stator with the chopper has a diameter of 7 cm and can become very loud when running at high power. Protect your ears and do not go near the horns during operation. The more power you give the motors, the louder they will be!
If you want to print the model, thank you! Unfortunately, there is no official control like the Thunderbolt has the RCM. I upload next week my AR-Timer and then i paste the link in the Commends. Be sure to write in the comments if you have any other ideas for siren projects. And feedback is always welcome!!!
License changet for @JaydeTheProt_3507071 for the STH-10. Check the model on his profile!
Have fun with the model :D