GIRO.remix - OctoPrint Raspberry Pi Camera Mount

GIRO.remix - OctoPrint Raspberry Pi Camera Mount

General

This is a remix of parkis' nicely designed Raspberry Pi Camera Mount for the Prusa i3. I nearly completely redesigned it to make it fit on my 3D printer with a different camera. The enclosure for the Raspberry Pi Camera was adjusted to make it fit for the OV5647 Model G Camera by Waveshare and is also available by SainSmart. You can grab it at one of the following links.

"Those links are just for reference and they might change over the time and you may not receive the correct camera so make sure that it's the right camera if you want to use this mounting."

Germany 

OV5647 Model G by SainSmart (Amazon_DE) 

OV5647 Model G by Waveshare (Amazon_DE)

There are two versions available. Version 1 uses the nut cap as a mounting for the M3 nut. The second version has the M3 nut locked in the front_plate.

For Version 1 you will need the following STL-Files.

1. GIRO.Remix_PiCam_Z-Rotary.stl
2. GIRO.Remix_PiCam_Base_Plate-stl
3. GIRO.Remix_PiCam_Knob_V1.stl
4. GIRO.Remix_PiCam_Nut_Cap.stl
5. GIRO.Remix_PiCam_Rear_Plate.stl
6. GIRO.Remix_PiCam_Front_Plate_V1.stl

For Version 2 you will need the following STL-Files.

1. GIRO.Remix_PiCam_Z-Rotary.stl
2. GIRO.Remix_PiCam_Base_Plate-stl
3. GIRO.Remix_PiCam_Knob_V2.stl
4. GIRO.Remix_PiCam_Rear_Plate.stl
5. GIRO.Remix_PiCam_Front_Plate_V2.stl

You will need additional screws to mount this camera mount on your 3D printer. 

Version 1:

• 1x M4 nut -GIRO.Remix_PiCam_Z-Rotary.stl
• 2x M4x10 -GIRO.Remix_PiCam_Base_Plate-stl
• 1x M4 Washer (Optional / not neccesary) -GIRO.Remix_PiCam_Base_Plate-stl
• 1x M3x40 screw with hexagonic screw head (ISO 4017) -GIRO.Remix_PiCam_Knob_V1.stl
• 1x M3 nut -GIRO.Remix_PiCam_Nut_Cap.stl

Version 2:

• 1x M4 nut -GIRO.Remix_PiCam_Z-Rotary.stl
• 2x M4x10 -GIRO.Remix_PiCam_Base_Plate-stl
• 1x M4 Washer (Optional / not neccesary) -GIRO.Remix_PiCam_Base_Plate-stl
• 1x M3x35 screw with hexagonic screw head (ISO 4017) -GIRO.Remix_PiCam_Knob_V2.stl
• 1x M3 nut -GIRO.Remix_PiCam_Front_Plate_V2.st

Printing

I would highly recommend to use exactly 2 perimeters because otherwise some areas aren't going to get really solid. Print with a lower speed, for example 30 mm/s, to get a more accurate printing. I recommend to print the enclosure with a 100% infill to get the most solid printing.

The STL-fileGIRO.remix_PiCam_Z-Rotary.stl must be paused after 5mm of printing and a nut (Size M4) must be placed into the hole with the hexagonic structure or you might not mount the camera on your printer!

Additional Information

Let me know if there are any kind of problems with the Raspberry Pi camera mount. I will try to help and if neccessary correct the designs. I appreciate any kind of feedback to these mountings.

If you like my work and find it really usefull then I would be very happy if you give me a small tip as an appreciation for my work.