Liczymy pasujące modele…
Needed a bracket that I could mount one of the common rectangular digital temp / humidity sensors to my 2020 extrusion. Works for top/side or bottom mounts with blind tnuts.
Compact and minimalist filament spool holder designed for 2020 extrusion. Takes up minimal space while remaining strong and stable. Fits spools up to 67 mm width. A separate version is available for 70 mm spools. A STEP file is included…
I wanted to have the filament run out sensor hang over the 2020 extrusion, as the Two Trees Bluer Plus uses an extrusion with a flat front but standard 2020 track on top. This uses M3x10 to self-tap into the plastic, and used the M5…
This is my design for a filament spool holder that will fit any 20mm wide V-slot rail. You will need to drill holes for mounting either through the sides or through the top (drill from the inside when drilling through the top) Use with…
These Idler blocks lets you use M5 hardware to tension your belts. You need 2xM5 nuts and 2x M5x20 bolts. The Idler towers needs to be drilled out with a 5-6mm bit to make room for the bolts.
Something I made during 2020. The middle layers are of clear PLA and the bottom and top layers are whatever color you'd like. R-Rated and G-Rated versions available. No supports required.
I wanted a horizontal mount for the SKR Mini E3 V2 to act as a secondary MCU for Tronxy X5SA Pro build. It needed to be in the front right side so it could be hooked to a display. Printed in PLA using Voron print specifications. Supports…
Needed a foot to raise my aluminum extrusion off of the floor so I designed and printed a small foot. Connect to aluminum extrusion using a single M5 bolt screwed into a t-nut. My print parameters: Printed in PETG 0.2mm layer height 15%…
Bracket to hold a 2020 to the rear frame. Parts needed 4x M5X10mm+ heat inserts 4x M5X50mm BHSC 5x M5X10mm BHSC 5x M5 v-slot nuts. Which ever type you generally use. The bracket with the larger slot goes on top. If you skip the middle…
Printed using ABS, PETG could work too. Designed for 3mm enclosure panels on 2020 extrusions. Print settings used: 3 walls at 0.42mm outer wall and 0.6mm inner wall Print 2x of the latch handle and latch base. Requires 2x M3x6mm screws to…
Remix of Draizer's shelf holder for 2020 extrusion. Instead of being inset into the 2020 frame, my board sits above the 2020 frame. This extends Draizer's design up to flush with the frame which allows 1 ¼-1 ½" screws to connect with the…
The original model had too small thread for the fitting, this model fixes that
I've reverse-engineered and refined the original system to enhance usability and design quality. Here’s what I’ve changed: Improved Pillars: Redesigned for easier assembly with better clipping functionality. Added chamfers to the edges…
2020 Connector 3 Way Corner Bracket EXTRASTRONG _Alu Profile Suitable for: Resize to adjust dimensions Warning: Dimensional Tolerance Notice Please be advised that final print dimensions can vary due to printer settings, calibration, and…
A simple printed mount for three 2-pin, or three 3-pin, JST-XH connectors. I used one to keep the fan wiring under my Voron Trident bed tidy. Then I could run a single fan power cable up from the electronics bay, and have connectors for…
I had been looking for a good scrap bin to put on the side of my Ender 3 V2, when I realized I could adapt the Gridfinity system to fit on 2020 extrusion. Similar ideas have been done before, but I tried to make this a well rounded…
Sun Visor Cap for Ford Fusion based on DS73-F040A26 I installed it in my car, and seems firmly in there. I increased a chamfer from 0.2 to 0.35 before uploading to ease removal when desired. If the cap doesn't stay in as desired, let me…
A few of the frame's I've ordered have had fairly thin anodizing that was prone to picking up scratches during the build process. I came up with these temporary feet so that I could lay the printer on any of its side without my work…
Sturdy Corner Bracket with Ribbed Reinforcement – Heavy Duty for 2020 / 3030 / 4040 / 5050 V-Slot & T-Slot aluminum profiles Perimetric reinforcing rib for superior strength Optimized profile geometry – better resistance and easier…
Affiliate links for my favorite filaments to help support what I do are here: Linktree When I got my iPhone 16 I found that with a case it would not fit in the Qi Charging slot. 3D printing and some modeling came to the rescue so I was…
This is a simple spoolholder to go inside a homecube or similar 2020 extrusion enclosure. It requires access to the bottom face of a top 2020 extrusion, and requires the side panel to lean against for structural stability. Use T-nuts or…
2020 Extruded Aluminum - Profiles Collection - Parametrico/Parametric - Adjust the Z scale to obtain longer profiles Available in 5 variants: 2020 4 Sides Open 2020 1 Sides Open 2020 2 Sides Open (90°) 2020 2 Sides Open (180°) 2020 3…
a 22.5 deg angle to mount the daylight-on-a-stick led board. uses a m3 pressed inset. two versions for the t-nut side the M5_2 is altered a little to not really need supports
I tested a bunch of cable clips and the model I found at https://www.thingiverse.com/thing:2613532 was my favorite. It requires some force (pliers help) to twist into place, but once there it holds firm. It's got a flexible arm so cables…
Print in PLA/PTG. The top extrusion is 100mm The small piece is 30mm The Part with the 3 holes is for adding ¼ 20 accessory thread, designed to be used with a ¼ 20 5mm insert and two m4 10m countersunk screws and T nuts.
EN Does your Hyundai i20N (model years 2020-2024) suffer from an annoying rattle coming from the back seats, especially when driving over uneven surfaces? You're not alone. The source of the noise is excessive play in the factory plastic…
End cap designed to fit 2020 B-type aluminium profile / extrusion with 6mm slot and 5.5 mm center hole. Added thickness is 1mm., the inside fingers are 5mm, It's a bit fiddly to put on but then it should sit pretty well. If you get a…
This is a 10" rack made from 2020 T-slot aluminium profiles. This rack doesn't fully comply with the 10" "standard", the screw spacing is slightly wider, some panels might not fit. Check measures before commiting. Some parts are too big…
I bought some cheap 24v kitchen cabinet led bars (https://nl.aliexpress.com/item/1005003166484007.html) and they differ in size from the one I already had that Formbot ships. They are slimmer and do not protrude from under the 2020…
Capture the raw power and iconic style with this 3D printable STL model of the Audi RS6 Avant. This legendary muscle car replica is perfect for automotive enthusiasts looking to display pure performance and classic design in their…
Experience the thrill of electric hypercar performance with this 3D printable STL model of the Tesla Roadster 2020. This all-electric supercar model is perfect for automotive enthusiasts and tech lovers looking to display the cutting-edge…
This is my version of an AWD DuEnder. The rails are all MGN9. When I get the chance, I will update this description with a parts list of used hardware to assemble, but most everything is an M3 bolt ranging from 5mm up to 35mm. Print…
Esta pieza es una unión tipo L diseñada específicamente para conectar perfiles de aluminio 2020 en ángulo recto. Su geometría refuerza la rigidez estructural del ensamblaje, permitiendo fijar dos perfiles de manera firme y estable sin…
Este soporte en L grande está diseñado para unir de forma rígida y estable la estructura hecha con perfiles de aluminio 2020 a la base de MDF del animatrónico. Su geometría amplia y reforzada distribuye mejor las cargas verticales y…
widened the bracket holes to fit better and allow it to be directly screwed into the angle bracket (such as these https://www.aliexpress.com/item/32707599936.html). Also removed the MGN slot. My frame had lots of space so the rail just…
A hinged metal arm for 3D printers, simplifying cable management with durability and easy maintenance in mind. Based on the open-source PRUSA SwingArm, this short, hinged metal arm guides a sleeved cable bundle (or a USB/CAN cable). The…
All Modifications have been created in Prusa Slicer. All 3MF Files are available. This mod can be used with the Tophat / Canopy for Vorons. CYD Case Mods: added 3.5mm holes (distance 30mm) to the Backplate. Voron Removable Doors (from…
Attribution & Background Full credit to lolthekidison for the original design concept for a cable chain top and bottom mount for the Rook Mk1 (heated bed). This model adapts that idea for the Rook 2020 Mk2 with a heated bed, with changes…
You just need 4 x M4 screws to attach the sides , 2x M8 countersunk screws and optionally a Pneumatic fitting for the PTFE Bowden tube.
Pieza deslizante con forma de T para perfil 2020. Permite encajar una tuerca de M3 (6mm de diametro exterior) Dimensiones: 10mm x 10mm x 5,3m
This model is for a shelf that sits above the sliding lid on a 2020-2022 Honda CR-V center console. The sliding lid moves under the shelf eliminating the need to remove items under the arm rest to open the compartment. The height is…
For those who want to add CAN bus to their Rook here is a handle mount that fits under the rook.
Simple extrusion mounted umbilical + ptfe tube holder for the duender. Use with PUG cable strain relief https://www.printables.com/model/378567-pug-parametric-umbilical-gland
2020 aluminum extrusion profiles are, 20mm x 20mm square T-slot. Commonly made from 6063 aluminum, for DIY projects like 3D printers, CNC machines, workbenches, and automation equipment
Update 07.02.2026: "Tight" & "Relaxed" Versions I have updated the naming convention and added a new variant based on assembly testing: Tight (Original): High-frequency wave for a firm, secure grip on wires. Relaxed (New): Wide-pitch…
Print, insert next to button, and forget it! Slide this little print next to the auto-stop/start button so that it is lit up when depressed. It will stay depressed and turn off the auto-stop "feature" automatically, every time you start…
This is a plug/dust cover for the holes on the pickup bed of 2015 to 2020 model years Chevy Chevrolet Colorado. I printed mine in 95Sha TPU for an interference fit I put my logo on mine, but left the uploaded model plain without any…
A camera mount for a vertical 2020 beam, ideally for an open coreXY. It can fold out of the way to remove the plate, in case you need the space. It uses; 1x m3 heatset insert 1x m3 nut 1x m3x8 screw 1x m3x45? screw 1x spring (ender 3…
This is a canting screw for Nordica Speedmachine 120 ski boots (2020 model). Compatibility: This screw does not fit newer models! Purpose: It serves as a replacement for lost screws that are no longer available from the manufacturer.…
The bed for the Voron Trident I'm building allows for two thermistors - the one that comes embedded in the heating pad and an independent one. I liked @methylene67_166296's design so I added a hole that allowed hard-wiring each thermistor…
Mejora tu Iluminación ¿Cansado de imprimir a oscuras o de que las sombras no te dejen ver la primera capa? Este soporte para tira LED está diseñado específicamente para impresoras con perfil de aluminio de la serie 20 (como la Ender 3,…
An organizer for the bushing, drills , taps for drilling accurate holes for 2020 V-slot aluminium extrusions. I printed this out of PLA. I used 4 walls, 4 top, 4 bottom layers. You can use PLA, ABS, or PETG. I did use a 8mm Brim to…
3D model inspired by a 2020 Nissan vehicle , designed specifically for dioramas, miniature environments, and scale model scenes . The proportions and details are optimized to look realistic at smaller scales while remaining easy to 3D…
Um ein 2020 Aluminiumprofil senkrecht aufzustellen, habe ich diesen Halter / Ständer generiert. Auf diesen wird das Aluminiumprofil aufgesteckt. Mit dem Programm openSCAD kann man die Maße recht einfach anpassen (die .scad Datei laden,…
I've created this armrest insert to aid in keeping things more organized in there. Box size is 120 x 167 mm and the brim is 128 x 171 mm. Brim size can be increased by about 6mm all around (3mm per side) if you want a snugger fit. The…
I used both sources to create a gridfinity based tool holder for my Vat Stand, based on a 2020 profile
I was not satisfied with the stiffness or size of the rotor blades for the giro2020 3D printed autogyro found here https://www.thingiverse.com/thing:4172759 . So I went searching for some off the shelf and other printed solutions. I found…
I wanted a simple bracket to hold 2020 extrusion on my workbench so I could work on wiring my toolheads. This is my solution.
I found that the original model nor the remix didn't really help prevent g twisting. That could be because I am using LDO extrusions where the slots seems to be a bit wider. I also found that the wedge on the remix that goes into the…
Mounting Info Uses M3 T‑nuts and screws (pictured with thumbscrews) Compatible with 2020/2040 extrusion profiles Mounting holes on two edges for flexible positioning Device Fit Supports devices up to 110 × 60 mm (with allowance) Device…
Holder for 3950 Thermistor for chamber temp that screws on the 2020 extrusion on ZeroG frame. It uses one M3x5x4 Voron style heat insert to secure the thermistor to the holder. Its made for use with two M3x8 sockethead screws and two M3…
Compact and minimalist filament spool holder designed for 2020 extrusion. Takes up minimal space while remaining strong and stable. Fits spools up to 67 mm width. A separate version is available for 70 mm spools. A STEP file is included…
I made this for my Mercury one.1 to drive cables inside the channels. It fits perfect, minimal space is reduced inside the channel. Model is 100mm long so if you break a piece you don't have to replace the whole cover I added the step…
This is one of the first multi-part things that I've designed so honest feedback would be appreciated! This Mount requires the following Hardware: -1x M5x10 Screw -1x M5 Nut (abt. 4mm thick) -2x M3x6 Screws -2x M3 Nuts (abt. 2,5mm thick)…
Wall mount holder for MacBook Air M1 2020 with 2 type-c ports. I used this type-c adapters:…
This magnetic corners allow me to remove and put the plexiglass pannels without hassle. This was made for 2,2mm plexiglass and 12mm diameter round magnets (2mm depth). Mind each printer will print with different tolerances. I print them…
NEW! Now with EVEN LOWER PROFILE! This version reduces increase to height of the printer. My prusa bear lives in a shelving unit now and I needed to reduce printer height as much as possible, but still wanted the noise dampening effects…
These jigs help keep the extrusions aligned so you can cut up to 4 at once for very accurate lengths. The side plates are designed for M5 cap head screws. My extrusions have an M6 center hole but I've included M5 also. Also an alignment…
2020 T-slot suitable for IKEA MITTLED lamp, small angle. Hardware: 2x M3 T-nut 2x M3 bolt
10mm channel negative space added so 10mm LEDs can slide into the channel securely without the adhesive.
Just a small corner bracket for 2020 profiles. It has small ellipsis instead of round holes to allow some adjustment. Edit 2024-12-28: added a stronger version with 4mm thickness instead of 3mm
I'm building a few Rook 2020 Mk2s and bought the Mellowfly D5 as a cost effective board to run these but it looks like there were no mount adapters so I slapped this together. Hopefully someone else will find this useful.
Converted the original into STEP format for the 3.5 and 5.5 no-logo latches. These are the standard voron BOM sizes.
Thinkcenter Rackmount for minirack, made compatible with narrow clearance of AL2020 extrustion rack
Didn't want to remove rails to slot in the original model, so made a snap on set.
I created this so I could mount my YIZHAN camera to some 2020 I have on my desk. It fits snugly with the camera and has 2 M4 holes either side so you can really make sure its secure. I have included the STEP file if you need to modify.
I have different magnets so I made a new one. Solidworks file included.
This is a clip-on thermistor mount for a Voron chamber designed for 2020 aluminum extrusion . Suited for thermistors with 3mm diameter. Unlike the original mount, this version clips directly onto the extrusion and does not require screws,…
General I liked the design of the attachment to screw down but the other model only fits for the 2018 Kona. So I redesigned it. For my car I did a version with lock nuts because due to vibrations normal nuts can get loose. The…
Motivation I wanted a nice looking and hidden camera mount for my C920 . So I made my own. Parts and BOM You'll need the camera and 2x m3 8mm or (2x 10mm?) BHCS screws and 2x m3 T-nuts. Printing Print as provided. Please use support for…
Corner frame brace for 2020 extrusion frame printers. Designed it for my Ender5 Plus. Most other frame braces I found only use a single screw on each side, providing only limited frame stiffening. These use 3x M4x10mm bolts and 3x T-nuts…
A phone mount for running Octo4a on the Ender 5 Plus. Designed for a Samsung Galaxy Note 9 with case (11.5mm thick, 81mm tall in landscape). Clips onto the 2020 aluminium extrusion using my spring clip base . If your phone has different…
Ich habe das Modell von @3DDruckByTeufel : https://www.printables.com/model/711664-winkel-fur-2020-alu-profil auf M4 Senkkopf Schrauben angepasst. Viel Spaß Sandra Beispiel für die Verwendung: https://youtube.com/shorts/TGAXD9fZTTs
Modified the original model to use two 2020 or 2040 aluminum extrusions 350mm in length. STEP file is included to remix extrusion length if needed. Also made it a little shallower to save on filament. I had some rubber adhesive strips I…
🚀 Support My Work🚀 If you enjoy my designs, you can help me keep the creative spark alive: Post a Make: Seeing your prints is the best reward! It also helps me earn Prusameters to keep the filament flowing. 💎 Like & Download: Your…
Simple part that allows you to mount a 10mm led strip onto a 2020 extrusion, at 45 degrees angle. Especially useful as 3d printer light for bedslinger models. Trim or elongate the model to fit your extrusion length, slide the led strip,…
I installed the tweeter on my Ford F150 from 2018, which had no B&O system. In case your mounting situation differs, feel free to modify the share the remix. Print suggestions To avoid warping during hot summers, print it in ASA or…
Mounts a BTT SFS 2.0 on a vertical (or horizontal) 2020 rail, and still allows panel removal. The sensor feeds filament perpendicular to the mounting rail
Universal 2020 T-Slot V-Slot Nut - M3 / M4 / M5 Double Thread Alu_Profile - Inserto universale per profili 2020 M3 Single M4 Single M5 Single M4 25mm Double M4 40mm Double M5 25mm Double M5 40mm Double Resize to adjust dimension…
A bracket for combining multiple 2020 extrusions at 90°. Fits 2x M5 fasteners at 8mm length with nuts. Compatible with:
![Rook 2020 MK2 & Scalable MK2 M5 Idler blocks [MK2]](https://media.printables.com/media/prints/1034193/images/7845167_bfd54e39-994f-4069-a3c6-44e2b49c3e21_a10bfcf2-06be-4ddd-98e9-dd113f4ce1a2/img_20241009_125921.jpg)
