1 / 6
Toyota Highlander (2020–2024) Overhead Sunglasses Holder Hinge – Replacement Kit — zdjęcie 1
1 / 6

Toyota Highlander (2020–2024) Overhead Sunglasses Holder Hinge – Replacement Kit

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is a replacement hinge repair kit for the overhead sunglasses holder found in Toyota Highlander models from

Ocena
0 / 5
Polubienia
5
Pobrania
77
Wydruki
0
Wyświetlenia
323
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a replacement hinge repair kit for the overhead sunglasses holder found in Toyota Highlander models from 2020–2024.

The factory hinge is a common failure point and not sold separately by Toyota, often requiring replacement of the entire overhead console assembly. This printable solution allows you to replace only the broken hinge, restoring normal operation at a fraction of the cost. This repair is only necessary for the right hand (passenger side) of the holder. Spring replacement is not required, but small amount of dampening grease on wear components could replace the factory slow release keeping the hinge relevant.

This model has been fully recreated from scratch and is from OEM placement/ fitment . The geometry matches the functional interface of the original hinge while being optimized for consumer 3D printing.

A similar model can be purchased in another similar form, US made, Here on EBay. Their auction aligns with the best install videos I’ve seen. Thanks @danielnc06 !


🚗 Vehicle Compatibility

Make

Model

Years

Toyota

Highlander

2020, 2021, 2022, 2023, 2024

⚠ Designed for vehicles equipped with the overhead sunglasses storage compartment.


🧱 Included Parts

This download includes three individual components, provided as 3MF files:

Part

Description

Hinge Arm

Main structural hinge component

Pivot Insert Style A

Interfaces with the tray body without OEM Spring

Pivot Insert Style B

Interfaces with the tray body with OEM Spring (slotted)

Each part is separated to allow:

  • Better print orientation

  • Improved strength

  • Easier replacement of individual components if needed


🖨 Print Recommendations

Setting

Recommendation

Material

PETG, ASA, ABS, HT-PLA (PLA not recommended for hot interiors)

SLA ABS type Resin or mix with Siraya Tech Tenacious Flex (as shown in photos) for a bit more elasticity - https://amzn.to/4s9EGJI

Layer Height

0.2 mm FDM or minimums for SLA/ MSLA

Walls / Perimeters

4+

Infill

100% 

Supports

None required for FDM

SLA/ MSLA print 45 with full supports

Print Orientation

Widest section down (internal posts as provided in 3MF) - Outer Seat 180 wide side down.
SLA rotate at 45

🌡 Automotive interiors experience high temperatures — heat-resistant materials are strongly recommended.


🔧 Installation Notes

  • Installation follows common aftermarket hinge replacements. 

  • No permanent vehicle modification required

  • Works with the existing sunglasses holder assembly

  • Reuses original hardware where applicable

🧰 Basic hand tools may be required depending on vehicle trim. More than likely hands only will be required.


💡 Why This Model?

  • Avoids full console replacement

  • Designed specifically for 3D printing

  • Modular 3-part construction for durability

  • Clean geometry with print-friendly tolerances

  • Ideal for DIY automotive interior repair

This part solves a widely reported issue on late-model Highlanders where the hinge breaks under normal use.


⚠ Disclaimer

  • This is an aftermarket repair part, not an OEM Toyota component

  • Vehicle trademarks are used only to describe compatibility

  • Always test fit before final assembly

  • No warranties explicit or implied.

Tagi