MODULITH 165 Wall Mount Starter Kit

Turn your wall into storage.

Screw up a bracket, hang the cases. The bracket goes on the wall with a few wood screws, and the cases hang on it: the screw heads slide into the keyhole slots in the case back and the bracket nests into its back opening. Rows below the top one lock on with QuickLocks, so you can swap or rearrange drawers in seconds.

Two builds, one download. Both layouts use the parts on this page, only the quantities change. Print the 3-drawer build to get started, or go straight to the 5-drawer.

Grow it whenever. Bracket sections install side by side, and more 165 cases hang beneath the top row, so this kit is just the beginning.

GEN2 is now MODULITH. Same system, same compatibility.

PICK YOUR BUILD

2W-2H · 3 drawers · 34 printed pieces in 27 print jobs
176 × 122 × 195 mm (W × H × D, with the bracket and faceplates)
See this exact kit: parts list, filament and print time →
Open its 3D build guide →

3W-2H · 5 drawers · 54 printed pieces in 43 print jobs
264 × 122 × 195 mm (W × H × D, with the bracket and faceplates)
See this exact kit: parts list, filament and print time →
Open its 3D build guide →

The guide opens in your browser with no sign-up: rotate the build and step through the assembly.

THE 165 COLLECTION

The 165 Collection offers efficient storage in a compact footprint, optimized for smaller printers like the Prusa Mini and Bambu Lab A1 Mini. It provides more room than the 115 mm drawers while maintaining fast print times and broad compatibility.

WHAT'S IN THE DOWNLOAD

• Wall brackets: Wall Mount Lite, 1W, 2W and 3W, one bracket design for every collection. The 2W-2H build uses a 2W and the 3W-2H a 3W, and sections install side by side if you grow

• Cases: 165-1W-1H and 165-2W-1H. The Wall Mount Lite bracket needs v2602 or newer cases, which these are

• Covers: 165 Cover Lower and Upper, 1W and 2W, to finish the top row

• Decor Drawers: v2609, 1W-1H and 2W-1H, the drawers the two builds use. They print with a tear-away front: snap it off, or leave it in unless you add a faceplate back cover

• Classic Faceplates: 1W-1H and 2W-1H, each as an STL and a ready-to-slice multi-material 3MF

• Classic Drawers: 1W-1H and 2W-1H, if you would rather print the handle into the drawer

• Side Covers: 165-1H as an STL and a two-material 3MF, an optional finish for the end walls

• Hardware: QuickLocks (print in PETG), optional drawer stoppers, 10x2mm and 6x2mm magnet inserts. The Bi-Directional QuickLock is for mixed-depth under-table builds: it is not for wall mounting

WANT A DIFFERENT FRONT?

The Classic Faceplates in this download are free. Every faceplate series of the same size fits the same Decor drawer, so you can change the look later without reprinting the drawer.

• EdgeLabel: snap-on faces with swappable printable labels. Easy multicolor, even on a single-color printer.

• Classic Pro: the classic look, with swappable labels and accents.

• Chevron: a 45 degree pattern that lines up across every drawer. Takes a separate bolt-on handle and M3 screws.

These three are paid models, each on its own page, and included with the Jerrari Club.

WHAT YOU PRINT

Quantities are prints, not parts. QuickLocks and Drawer Stoppers each come as a left/right pair on one plate, so one print gives you both pieces.

2W-2H · 3 drawers

• 1 × Wall Mount Lite Bracket, 2W section

• 2 × 165-1W-1H Case

• 1 × 165-2W-1H Case

• 2 × Decor Drawer 165-1W-1H

• 1 × Decor Drawer 165-2W-1H

• 2 × Classic Faceplate 1W-1H

• 1 × Classic Faceplate 2W-1H

• 2 × 165 Cover Lower 1W

• 2 × 165 Cover Upper 1W

• 3 × QuickLock A (print in PETG)

• 6 × Magnet Insert (optional, for the magnetic closure)

• 4 × Drawer Stoppers (optional)

• 4 × 165-1H Side Cover (optional finish, not in the printed-piece count)

3W-2H · 5 drawers

• 1 × Wall Mount Lite Bracket, 3W section

• 4 × 165-1W-1H Case

• 1 × 165-2W-1H Case

• 4 × Decor Drawer 165-1W-1H

• 1 × Decor Drawer 165-2W-1H

• 4 × Classic Faceplate 1W-1H

• 1 × Classic Faceplate 2W-1H

• 3 × 165 Cover Lower 1W

• 3 × 165 Cover Upper 1W

• 5 × QuickLock A (print in PETG)

• 10 × Magnet Insert (optional, for the magnetic closure)

• 6 × Drawer Stoppers (optional)

• 4 × 165-1H Side Cover (optional finish, not in the printed-piece count)

WHAT YOU'LL NEED

• Wood screws: 4 for the 2W-2H, 6 for the 3W-2H, two per 1W. Countersunk #6 or #8. Screw length and anchors depend on your wall: go into a stud wherever you can, use wall anchors in drywall with no stud, and any other wall material needs a fixing made for it.

• Tools: a screwdriver, a drill bit smaller than your screws, and a pen, marker or scratch awl to mark the holes.

• Filament: PLA or PETG.

• Magnets (optional): 6 or 10, 10×2mm or 6×2mm, only if you add the magnetic closure.

• M3 screws (optional): one M3×6mm socket head screw and one M3 hex nut per 1W cover, only to fix the covers in place.

As an Amazon Associate I earn from qualifying purchases.

No load rating is published, so judge what you store in it and check the fixings yourself. Narrow cases go on top because the case walls nearest the support carry hanging weight better; that is design guidance, not a load test.

LET THE FREE PLANNER HANDLE THE DETAILS

Want a different layout? Build it in the free MODULITH Planner: it works out the parts, hands you a complete parts list with download links, shows it in your own filament colors, and generates a step-by-step 3D assembly guide for your exact setup.

👉 Open the free MODULITH Planner →

INSTRUCTIONS

🔧 Step-by-step wall mount instructions →

🎥 Watch the wall mount video

PRINT SETTINGS

• Recommended filament: PLA, or PETG or ABS for heavier duty storage

• QuickLocks: PETG

• Nozzle: 0.4mm

• Layer height: 0.2-0.35mm

• Infill: 10-20%

• Supports: None

KEEP BUILDING

• 165 Decor Drawers

• 165 Cases

• 165 Side Covers

• Classic Faceplates, free

• Wall Mount Brackets on their own

• 165 Tabletop Starter Kit

SUPPORT MODULITH AND UNLOCK MORE

Join the Jerrari Club for member-exclusive models and early access. Every membership helps fund new MODULITH releases and free tools like the Planner.

NEW TO MODULITH?

🎥 Watch the system overview

UPDATES

2026-11 - Page refreshed for MODULITH (formerly GEN2), with a new cover and links to the exact 2W-2H and 3W-2H builds and their 3D guides. The download now includes the v2609 Decor Drawers, the v2602 Covers, the Classic Faceplates and the Side Covers those builds use.

v2602 introduced the Wall Mount Lite bracket, which replaces the drill templates and guides the screws to the correct depth. It only supports v2602 or newer cases.

This model is licensed CC BY-NC-SA 4.0. The Non-Commercial part refers specifically to selling prints. You're absolutely welcome to use my designs in commercial environments, I actually encourage you to use them anywhere you see fit! 👍