Heavy-Duty Toolhead Mod for Artillery SW X4 Series (Pro and Plus)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Dual 5015 radial for part cooling, 4010 axial for the heatsink. Less noise and more cooling power!
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 10
- Wydruki
- 0
- Wyświetlenia
- 108
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
High Performance Toolhead Conversion for Artillery Sidewinder X4 Pro / X4 Plus (Dual 5015)
WARNING
This is not a simple plug-and-play mod. It requires several modifications to the machine, some of which are PERMANENT. If you are not willing to make these changes, DO NOT attempt to install this mod.
Required mods:
-A 15mm spacer for the X-axis endstop (or shorter if you modify the left-pulley/motor cover).
-A custom right-pulley X-axis cover (or adjusting the maximum position in your Klipper config).
-A drilled hole in the toolhead backplate to reposition the inductive probe.
-Printer config file modifications to accommodate the hardware changes (including bed size adjustments in your slicer profile) and to configure the 5015 fans to operate properly without buzzing.
I am providing detailed instructions, and all files in .step format for anyone who wants to improve or customize the design.
Required hardware:
8x M3 x 20mm countersunk bolts (or 25mm button/socket head bolts, trimmed to 23mm)
1x M3 x 7–10mm bolt
9x M3 x 4mm heat-set inserts
1x M3 x [Length]mm button head bolt
2x M2.5 x 6mm flat head bolts
2x M2.5 x 3mm heat-set inserts
The parts are pre-oriented for printing with minimal supports. PETG or a material with higher thermal resistance (like ABS or ASA) is highly recommended.
Assembly instructions:
1) Install Heat-Set Inserts
Carefully install the M3 heat-set inserts into the 9 M3 holes. Note: The central bracket only takes 2 inserts (one in each "ear") because the 4 holes for the 4010 fan are PASS-THROUGH clearance holes! (Important: The remaining two inserts are M2.5, located under the heatsink funnel to hold the ducts).
Do not disassemble your printer until you have verified that all parts printed correctly and heat-set inserts are properly installed. This ensures you can easily print replacements if anything goes wrong.

2) Strip Backplate
Completely disassemble the toolhead and remove the backplate from the carriage.
3) Drill Probe Wire Hole
With the backplate completely stripped, drill a clearance hole for the probe cable to pass from behind the plate to the PCB (see the image below step 5). (You will need to depin or remove the plug connector and reattach it after routing the cable).
4) Reassemble Backplate
Reinstall the backplate onto the carriage, mount the PCB and LED board, then plug in the probe and ribbon cable.
5) Prepare 4010 Fan
Connect the 4010 fan and leave it hanging for now. (You will likely need to solder/use the connector from the original 3010 fan).

6) Save Original Screw
Remove the original 3010 heatsink fan and keep one of its screws (M3 x 17mm).
7) Install Heatsink Funnel
Mount the funnel over the heatsink using an M3 x 7–10mm bolt on the left side...

....and the saved M3 x 17mm screw on the right side. Press the parts tightly together while tightening to prevent any gap between the heat-set inserts:

Top view:

8) Attach Central Bracket
Attach the central bracket to the heatsink funnel (light push fit):

9) Install 4010 Fan
On the central bracket. (Note: My fan had hexagonal recessed holes for nuts, so I used countersunk M3 x 20mm bolts with 2mm printed hexagonal washers):

10) Prepare 5015 Fans
Attach the support arms to the respective 5015 fans for each side. Measure the required wire length, then cut and solder both fan cables together into a single connector:
Left fan:

Right fan and soldered joint:

11) Mount 5015 Fans
Install both, mounting them to the backplate and central bracket, then connect them to the PCB:
Left side:

Right side:

12) Install Air Ducts
Mount both ducts using the M2.5 bolts, pressing them flush against the fan outlets:

13) Final Check
Check all bolt tightness, and you're done!

That completes the physical cooling setup. Now, let's configure the software to get everything running properly!
Software Configuration
1) X-Axis Limits & Bed Size Adjustments
Because of the 15mm spacer on the X-endstop and the modified physical travel, you must adjust your stepper limits so the nozzle homes safely without crashing.
[stepper_x]
position_min: 9
position_endstop: 9
position_max: 2412. Inductive Probe Offset
Since you drilled a hole in the backplate and relocated the inductive probe, you must calibrate and update its Y-offset relative to the nozzle:
[probe]
pin:PA8
x_offset:-18
y_offset: 283. Bed Mesh Coordinates
Update your mesh boundaries so the probe stays safely on the bed surface during probing, accounting for the new probe offsets and X-endstop shift:
[bed_mesh]
mesh_min:15,29
mesh_max:223,2354. Dual 5015 Fan Setup (Eliminating PWM Buzz)
5015 blower fans often produce an annoying high-pitched buzzing sound when dimmed using standard PWM frequencies. To prevent this, set a low cycle_time:
[fan]
pin:PA4
max_power: 1.0
shutdown_speed: 0
cycle_time: 0.000056
hardware_pwm: False
kick_start_time: 0.800
off_below: 0.105. Hotend Fan (4010 Fan Configuration)
Ensure your 4010 heatsink fan is configured to turn on automatically when the hotend reaches 45°C:
pin: PC7
heater_temp: 45.06. Slicer Profile Updates (OrcaSlicer)
Don't forget to update your slicer settings to reflect the new physical bed dimensions and printable envelope:
Printable Area: Adjust your X boundaries in Printer Settings / Basic Information / Printable Area:
For a position_min of -9 and a position_max of 241 on stepper_x, the total printable width is 232 mm with an X origin of -9:

Y-Axis Setup: Note that I have set the Y-axis origin to -3 and the size to 240, which leaves a nice margin for the purge line while giving 240 mm of usable length along Y. For reference, these numbers correspond to the following Klipper values:
[stepper_y]
position_min: 0
position_endstop:0
position_max:250Final Steps
Now that the new hardware is configured, it's time to run a few calibrations:
Input Shaping
Z-Offset
PID tuning (using your typical nozzle/bed temperatures and fan speeds)
Note: If you also swapped your nozzle for a 0.6 mm CHT Volcano and a bi-metal heatbreak (which is the main reason I created this mod!), you may need to re-calibrate your flow ratio, pressure advance, retraction settings, and max volumetric flow in your slicer filament profiles!