3928 modeli
Note: the coned center section design saves print time (prior design required individual deposition points for 12 tiny dots that often failed, but that are eliminated here) and provides the strength needed to eliminate the vertical links…
Calibration cube to test 3D printers. This is old version of my All-in-One Calibration Cube. If you want do download never one, click this link witch redirects you to new version or just find it on my profile among uploaded models.…
Basically prints without support and brim, but I'd recommend a 5-10mm brim (as in the .3mf file). 0.6mm nozzle and 0.25mm layer height is fine, although you might reduce it for a higher quality print. Do yourself a favour and use PETG or…
Update 25/08/2023 v1.2 added - access for heat break setscrew created, small amount of material added on the fan-side of the grille near the bottom to ensure proper clearance to heatsink fan. Update 11/04/2023 v1.1 added - probe bracket…
IKEA Skadis compliant wall panel with 6x6, 5x5, 4x4 holes and other sizes. The standoffs are 25mm. The front will be 30mm from the wall. Mounted with 4x screws, ideall sunken head. Print with 10% gyroid infill, 3 top, 3 bottom layers, 3…
24cm radius jig for the Makita Router Circle Jig (RT0700CX4). Uses M6 Hex hardware
UPDATE April 23-24, 2024 — Remodeled how the retainer clip is attached, to get better grip strength. This involved a remix of both the chain link and the clip. Version 1.14 and up has this. Also, added two new sets. Original was renamed…
English below 2 Möglichkeiten zur Überprüfung des Flows: Hinweis: Wenn Du größere oder kleinere Würfel bevorzugst, skaliere sie bitte mit deinem Slicer auf die von dir bevorzugte Größe. 1. Möglichkeit zur Berechnung des Flows: Wähle…
Intended to be used in the Formd T1 case in 3 slot configuration with the air cooling holy trinity: Thermalright AXP-x47 Full Copper Noctua NF-A9x14 Noctua NA-FD1 The pegs are designed to be friction fit and clear the fan retainer clips.…
G wagon - True scale model After months of designing and testing, The design is finally ready. A Performance RC model with offroad capabilities. The chassis has ~150 printed parts. Join our : Discord The body for this Chassis can be…
This is a 3x4 gridfinity usb cable organzier for 12 x cables . The diameter per cable is approx. 12mm. Have fun and don't forget to post your makes :-) Check out my other designs and follow me for more.
Please leave a comment if you have any possible improvements to make to these profiles 😉👍 Print speeds? Benchy : about 45 minutes Calibration cube : about 13 minutes How import profiles? In PrusaSlicer Here is the link on how to do it:…
Update (08.12.2023): I reworked these models to meet the correct Gridfinity Specs. I based the first version on this model: https://www.printables.com/de/model/399759-actually-parametric-gridfinity-base-grid-bins , which sadly does not…
Rancher 4×4 – 3d printable set of parts for your 3d printer. Model is approx. 53 cm long (1:8 scale) and is prepared for your RC equipment. You can buy this model on www.3dsets.com What you get: 3d printing files: .stl and .gcode…
I really like the parametric Gridfinity Storage box by Pred, but I don't need the stackable design. And I even like the look of the rugged box by Whity more. So I combined both of them in a 4x5 Gridfinity box. The box holds 6U high bins…
a 2x4 lego brick made from the original 2x6high.
EN: Wall plug, dowel, size 10x45 mm. CZ: Hmoždinka - velikost 10x45 mm Print instructions === EN ======= If you want different size, increase or decrease % print size as you want. PETG is appropriate material. See my other designs! === CZ…
The .223 Remington is a rifle cartridge developed in 1957 as a hunting bullet. A military version, the M193, was used by the United States Army in the M16 rifle. The 5.56x45mm NATO was also developed from the .223 Remington. Category:…
Designed for Ender3v2 to mount behind the LCD screen. I would imagine this works with other Ender 3s but I cannot confirm You'll want to use supports for the rails If you're looking for a mount to go in middle to replace the drawer, see…
Calibration cube to test 3D printers. New V2 version included some fixes that stiffens overhang test, makes it easier to read the overhang angle and some more. Calibration Cube All-in-One Included: Letters to identify axis Calibration…
I have developed a chain drive for Traxxas TRX4 RC cars, which can be almost completely 3D printed. All you need are a few ball bearings and M3 screws. The drive train is fully functional and has already been tested extensively (in snow…
This clamp is designed to hold two 2x4 wooden planks together at a 90 degree angle so that holes can be drilled to secure both boards together. Worked well for my purposes. Do note that you will need more walls while printing in order to…
1/18 scale version of the original 1/10 by MrStolarsky. Pins were re-aligned and the whole board was made stackable. I test printed mine in resin and they came out awesome. I designed hangers for the Traxxas TRX-4M Defender, to hang a…
🧱Lego Duplo Brick 2x4 #3011🧱 RICORDATI CHE OGNI PERIODO DI GIORNI PUBBLICHIAMO I NUOVI PROGETTI (ANCHE LEGO) QUINDI ISCRITIVI,👤 SCARICA⬇ E LASCIA UN LIKE👍. REMEMBER THAT EVERY PERIOD OF DAYS WE PUBLISH NEW PROJECTS (ALSO LEGO) THEN…
Hi everyone, this is a case for a 20x4 lcd. It has an I2C on its back. As you can see the cables for the I2C going out on the left side. It has holes on its back to mount it where ever you want. Bring front and back together with screws.…
I designed this conversion adapter to mount a 120mm fan I had on hand because I didn't like the appearance of the stock fan included with the AXP90-X47. Required other than printed parts: 4x M3x5x4mm heat-set Inserts 4x M3 screws,…
I remixed @dissendat_154107 model of a gridfinity pen holder for 4 pens for a more compatible stackable version for my fountain pens. Original measures 2x4 3U high. I adjustet heigth to 4U Can hold up to 4 pens. Now for bigger fountain…
BEFORE IMPORT CONFIGS YOU NEED TO HAVE KLIPER 0.4 PRINTER ON ORCA , IF YOU DONT HAVE THIS AN ERROR WILL POP UP THAT SAY 0 CONFIG IMPORT (SEE PHOTO) I have used this profile for big and small prints so its safe and tested you can see the…
Tired of gloopy overhangs? Need to mount gridfinity organizers on an IKEA skadis pegboard? Welp, here it is! Remixed @glitchprinter's 2x4 baseplate with four ikea skadis universal mounts. --- Parts used in this remix Magnetic Frame - 2x4…
🆕 Available on Etsy, from me, with free shipping These are 1:10 scale recovery boards for RC crawlers and other toys. I really made these for a fridge magnet but folks at Etsy loved it for the detail. I am sure the community here on…
Garbage Bin - 24x24x45 cm Consider following me on Instagram I post all of my projects to build a portfolio of my projects. https://www.instagram.com/smackmax_/ Fully Printed Waste Bin Tub under needs a bit of support 240 x 240 x 450 mm…
This 3D-printable model draws heavy inspiration from other 1:12 and 1:16 scale models. Every component was designed from the ground up specifically for 3D printing. Not much into RC's? Check out this flexible rolling chassis instead!…
This model is a remix of: https://www.thingiverse.com/thing:5251321 Scale about 1/10. I did following changes: I fixed the model so it's 3D printable Attempted to turn the model into european version: removed trunk lid handle added dual…
Summary sliding puzzle 4x4 print in place there are 3 versions: with 0.15, 0.2 and 0.3mm gap. to make it easier to move the stones, i recommend applying 1 drop of silicone grease to a cotton swab and carefully wetting the sliding points…
This is an improved version of my previous paint holder, having two advantages: a) can be printed without any support b) vallejo-paint bottles can be stored head down at all positions - this is especially helpful if the bottle gets close…
G wagon - True scale model After months of designing and testing, The design is finally ready. A Performance RC model with offroad capabilities. Join our : Discord The Chassis for this model can be downloaded here:…
A simple but suitable filament spool guide for the Space Pi X4 and X4L filament dryer from Creality. This prevents the spool from jamming when it's almost used up. Because the spool is too light, it can cause the spool to skew. This can…
Here's a basic 2x4 gridfinity bin.
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill No support needed. Watch it in action at
here is my jeep wrangler body for a trx4m. i print the main body and glue the details on how ever you want. it comes with the bumpers it needs to be put on a trx4m. it wont work on the normal bumpers. be sure to support the main body well…
Since the clip that comes with Rituals Car perfume is too narrow/small to use on the Hyundai Tucson vent wing, I designed this for the same and it fits pretty well.
4x4 Off Road Car Model This time, I'm presenting a 4x4 car model. In my opinion, the best way to print it is in a vertical position. But maybe someone has a different idea. Removing the supports takes a bit of effort, but I think it's…
Updated 5/29/2023 - Redesigned to clean up the model and add PS4 and Tribute64 controller compatibility, and replaced one of the AA battery spots with a space for a USB dongle. Gridfinity-compatible 3x4 storage block for Xbox One, PS4,…
Two stands for the ddj-flx4 dj controller to tilt it towards me. Maybe it works with other controllers too :D
I designed this model to squeeze a bit more performance out of the Thermalright AXP90-x47 CPU cooler in the FormD T1 v2 case. The duct prevents re-circulation and ingestion of hot air into the cooler and can provide some passive cooling…
A simple shackle for my Traxxas TRX-4M Defender bumpers. Printed in resin and painted. Paper clip can be used to be pressed in to fasten it to the bumpers. Drop of glue might be needed at the ends to secure the paper clip in (I did not…
Simple Gridfinity bin. The name of the objects are the dimensions, for x and y and the height. The height is a multiple of 7mm: 2 = 14mm 3 = 21mm 4 = 28mm 6 = 42mm The x and y are multiples of 42mm: 1 = 42mm 2 = 84mm 3 = 126mm 4 = 168mm…
18650 battery holder 1x4 4S1P. Remixed from : https://www.thingiverse.com/thing:4700523
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill No support needed. Watch it in action at
Prints Per track (4 total): 8x small_wheel 2x large wheel 8x skate 1x inner_rail 1x outer_rail 3x stand_off 1x gear 1x removable_bearing_interface 1x outer_retainer 1x of the following depending on position inner_retainer_rear L…
This is the exact replica of the original Lego 2x4 Brick. Not very original but I was teaching someone how to use sketches in Fusion 360 and I thought that, maybe, someone would want to have the actual Fusion 360 F3D file. There are no…
Wheels for the Traxxass TRX-4M Defender. All fit the original rubber and have the same offset as stock by default. Alternate versions with +X push the wheel out by Xmm, the wheel sits further out. -X brings the wheel closer to the body by…
O scale wooden barrels. Could be used as 28mm Tabletop gaming scatter terrain too.
Эта 3D-модель представляет собой компактную антистресс-игрушку в виде блока из четырех механических клавиш, расположенных в ряд. Модель предназначена для установки настоящих механических переключателей (MX-совместимых) и кейкапов, что…
UPDATE 05/07/2025 : the step files are now available ! I originally created this high clearance / low profile bumper for the Trx4m Bronco to solve the issue of poor attack and departure angle, as well as to reduce rubbing of the wheels…
This is a mixer tool for mixing. It prints without supports, the hexagonal handle has a standard 1/4 size and attaches directly to your electric drill. Diameter = 40mm Head height = 40mm Hex handle Length = 160mm
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill No support needed. Watch it in action at
Updated Model - See changelog Change log: Made the infill MUCH lighter on filament consumption, will also print much quicker; Improved chamfer dimension to make it easier to separate both parts; Made snapping tolerance better and shaped…
a Nozzle Holder that fits inside a 40x40 Aluminium V Slot extrusion. Common on many Printers, in my case its an Ender 3 Pro Fits 18 Nozzles and Usually you can Fit 2 of these on your printer, or 4 if you don't mind putting them on the…
Features: - suportless magnet holes - easy to get the pen or sharpie from tray - stackable design
Case for HAMTYSAN 7 Inch Portable Monitor External Display 800x480 for: https://www.amazon.com/dp/B0B8S9DYQC Legs used also as a harness for Raspberry Pi 4 Model B case, from here: https://www.amazon.com/gp/product/B07D3S4KBK
For the rails use the V12 rails from @Paul_318082 https://www.printables.com/model/440401-under-desk-drawer Update 15-5-2023: Update the drawers to V12
This is a remix of CG-Tech's excellent extruder stepper motor cooling fan add-on on Thingiverse. EDIT: I've uploaded a second version with deflected air ducts, based on CG-Tech's alternative one. It was a quick bodge and the stl file is…
Hello, This is a nice mashup of the Parametric Gridfinity base plate by @Cunfusu and the Rugged Box by @Whity . Enjoy! Also pictured is my Gridfinity Bambu Nozzle part https://than.gs/m/842099 EDIT: Added a model to be printed in TPU to…
There are lots of 3D printed Keurig cup holders, and this is mine. Wife requested a slim fit 8-cup holder. Base is 4.25 x 3 inches, and it stands about 8.5 inches tall. Printed at 0.28 w/ 20% infill. Category: Kitchen & Dining
This is inspired by the dozens of horizontal plier racks for gridfinity. This design has the following improvements: Wider slots (6 in a 3x vs 7) Shorter at 4x vs 5x Top lip which holds spring loaded pliers and nippers in a more compact…
Nintendo switch cartridge case, designed to fit in the Super Mario Odyssey carrying case. 2023-07-01 - Updated with new open back design to allow easier removal. Print Settings Printer: Kossel Delta Rafts: No Supports: No Resolution:…
Download ZIP, not STL Extract ZIP Open ORCASLICER FILES -> IMPORT -> CHOOSE FILE : SW X4 PLUS(or PRO) S1 - HAROVLEYGE.orca_printer For max speed (500mm/s and 10k mm/s) use fast filament settings.
Please be aware the model uses light weight modeling so has at points thin walls of 0.8mm, some users have indicated they had structural issues if they don't have a well calibrated printer. Inspired by AaronOaks model, unfortunately my…
CHANGELOG: 4/2/2020: Updated the model to have more support between bands. This makes it a little harder to pull apart, but ensures that the bands adhere well to each other, as I found that some layers would not adhere and cause stringing…
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill No support needed. Use the rings to space out the planks on a rope between the two ends. You can use two…
A stackable Gridfinity Container with an Inlay to store different versions of the Knipex Super Knips. Designed in two parts so you can reuse the container even if you get different Knips. The Inlay has some magnet holes on the bottom and…
U původní mřížky byly zámky na můj vkus až příliš volné, upravil jsem tedy přesnost zámků, těsnost políček pro dlaždice a trochu snížil výšku oddělujících křížků. Díky moc za původní model, který jsem jen lehce dotvořil ke své…
Helps to prevent hot air from recirculating into the CPU cooler fan. The internal chamber of my case get very hot, even with a 120mm exhaust fan installed. On my Terra, it reduces CPU temperatures by upwards of 13C. Before installing this…
Front light guard for my Traxxas TRX-4M Defender. I printed mine in resin and glued them on. Print some spares as the thin tubes might get broken in print (0.5mm in diameter). I printed 4 at a time and one guard had one bar broken.…
This project is meant to replace the buffer unit for the mmu3 by rewinding filament instead. The printed parts for this are as follows(I printed all the parts in PETG, no supports needed): Amount to Print File Name Comments 4 All Bracket…
Layer height: 0.15 Initial Layer Height: 0.4 How to get great quality: Legs and arms must be printed vertically (Be careful to not F*ck up with Z axis) Slow the printing process (I did on 120mm/s) Tree support is a must 10% infill 65°…
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill Support is needed. Watch it in action at
Wenn das Ende eines Kabelkanals sichtbar bleibt, ist das unschön. Ich fand leider nur ein 3D-Modell eines Halters für die 60x40 Kabelkanäle, aber habe es mit OpenSCAD quick&dirty um eine Blende erweitert, diese gedruckt und teile nun hier…
This one is designed for the bronco/defender style chassis. I will update later with the option to use it on a high trail later on. Assembly for the base frame is coded with colors: Yellow = M2.5 x 15mm, total 4 pieces Green = M2 x 8mm,…
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill No support needed. All 3 parts can be connected using the 3 way connector These corner parts are not…
○120mm extend to switch from a 4WD to a 6WD See instructions (pdf build guide file)
Remixed from a scx24 snowplow. Replaces front bumper. Body does not clip in unless someone wants to remix it. Requires 2 m2x6 screws and a paperclip.
I designed this spool holder for QIDI printers because the original one, when used with cardboard spools, often created too much friction. This could lead to false filament tangle detections and also generate annoying noise. After…
Based on the work of ZackFreedman .
Two models are available: One that supports case-less AND my case. The other changes the location of the charge port to be higher, if you're using a case that needs it. Print the stand on its side, hole facing up. No supports needed. For…
A simple holder for 1x4 sized coffee filters. Best printed with the longest edge facing the bed.
This is a 4x4 puzzle cube. It's very hard because the pieces are big and very unique. Piece 2 needs support I made a much harder 4x4 cube wich also doesnt need support. check this model out:…
I was on the Gridfinity train, planning out my first drawer, and I had ALMOST enough room for one more section, but not quite. So, I made a filler version that is, of course, 7mm smaller in width than the original size. That way, I don't…
A heat shield designed to stop hot air in the Creality Space Pi X4 and X4L from blowing directly onto the filament spools while drying. I found DJR Engineering 's heat shield on Makerworld . It was too flimsy for me, though. So I designed…
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill No support needed. Watch it in action at
Remix from : https://www.thingiverse.com/thing:4700523
Collection of screws (ISO 4017 / DIN 933) including : M4x 6, 8, 10, 12, 14, 16, 20, 22, 25, 30, 35, 40 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I…
Vytvořil jsem kalibrační kostku o rozměrech 40x40x40mm všechny hrany kromě těch co leží na podložce mají zaoblené hrany
Create your own 1/18th scale crawler track with these interconnecting track parts. Printed with 0.3 layer height on Mk3s 10 % infill Support is needed. Watch it in action at
Thanks for Bernie sharing that great model - please like his model as well. Printed in PLA 0.2mm layer height without supports and 15% infill (10 or 5% should work as well). First put the two parts of the battery holder together then…
a 7x4x3 variant of David's Multiboard open bin system for objects wider than 15cm
![Gridfinity baseplate [2x4] with Skadis Universal Hook mounts for IKEA pegboard](https://media.printables.com/media/prints/470819/images/3857666_7ac9f740-3494-4946-9ed0-4cf2565ed3cb/img_8401.jpeg)
