1 / 10
PNX CHG-3617 – 36:1 Compound Helical Gearbox for NEMA 17 — zdjęcie 1
1 / 10

PNX CHG-3617 – 36:1 Compound Helical Gearbox for NEMA 17

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

3D-printable 36:1 compound helical gearbox designed for NEMA 17 stepper motors and robotic joints.

Ocena
0 / 5
Polubienia
7
Pobrania
78
Wydruki
0
Wyświetlenia
298
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

PNX CHG-3617 — 36:1 FDM Compound Planetary Gearbox for Robot Joints

https://youtube.com/shorts/Z76G_8fSFTo?feature=share

Project Overview

PNX CHG-3617 is a 36:1 FDM compound planetary gearbox for robot joints, designed to mount directly to a NEMA17 stepper motor.

The gearbox uses compound planet gears in which the upper and lower gears have different tooth counts but are integrated into a single rigid part. This makes it possible to achieve a high reduction ratio within a relatively short axial package.

The design is intended for rotating robot joints such as the base, shoulder, elbow, and wrist. The main structural parts and gears can be produced using FDM 3D printing.

The gearbox is also designed to be serviceable. The gears, output section, and housing can be separated so that worn or damaged printed parts can be reprinted and replaced individually.

Main Specifications

Model: PNX CHG-3617

Reduction ratio: 36:1

Motor: NEMA17

Gear module: Module 1.0

Pressure angle: 20°

Compound planet gears: 3

Planet arrangement: 120° equal spacing

Output bearing: 30 × 42 × 7 mm

Input sun gear: 12T

Upper planet gear: 24T

Fixed ring gear: 60T

Upper sun gear: 18T

Lower planet gear: 18T

Output ring gear: 54T

Recommended gear material: PETG

Manufacturing method: FDM 3D printing

The upper 24T gear and lower 18T gear are printed as one compound planet gear, and three compound planet gears are arranged at 120° intervals.

Gearbox Features

1. 36:1 Compound Planetary Reduction

The 12T input sun gear mounts directly to the NEMA17 motor shaft and acts as the gearbox input.

The input rotation is transferred through the three compound planet gears. The different upper and lower gear combinations generate the final 36:1 reduction ratio at the output ring gear.

The main purpose of this design is to achieve a high reduction ratio in one compact mechanism without stacking multiple separate reduction stages in a long axial arrangement.

2. Three Compound Planet Gears

The gearbox uses three compound planet gears arranged at 120° intervals.

The three planets provide multiple gear-mesh points for torque transmission and help keep the output ring gear centered during rotation.

Because FDM parts may contain dimensional errors and material deformation, the three planets may not share load perfectly equally.

After assembly, verify that all three compound planets mesh naturally and that no single planet is excessively tight or repeatedly binds at a particular angular position.

3. Helical Gear Geometry

The gear teeth use a helical profile.

Compared with spur gears, the tooth engagement is more gradual. The goal is to reduce sudden meshing impact, vibration, and noise that can occur in FDM-printed gears and to achieve smoother operation.

Actual operating behavior will depend on:

XY dimensional accuracy of the printer

layer height

extrusion amount

filament characteristics

gear tooth surface quality

lubrication

bearing alignment

motor shaft alignment

assembly tolerances

4. Bearing-Supported Output

The output section uses a 30 × 42 × 7 mm ball bearing.

The output gear and output bearing part are separate components and are fastened together with M3 screws.

The bearing is positioned close to the output section so that external loads from the robot link can be transferred to the housing through a short structural load path.

5. Modular and Serviceable Structure

The major gears and structural parts are designed to be separable.

If an FDM part becomes worn or damaged, the entire gearbox does not need to be reproduced. Only the affected component can be reprinted and replaced.

Mounting the Gearbox to External Structures

Separate drawings are included showing how to mount the gearbox output to a robot link or another structure, and how to mount the NEMA17 motor and the lower side of the gearbox to an external frame or other component.

Use the supplied drawings when designing:

output-side mounting interfaces

output bolt patterns

robot-link mounting surfaces

motor-side mounting interfaces

lower gearbox mounting points

custom brackets and adapters

For the most accurate integration, import the supplied STEP assembly into your CAD software and check dimensions and interference directly before designing the mating parts.

Required Parts and Fasteners

Main Components

NEMA17 stepper motor

30 × 42 × 7 mm ball bearing

Complete set of printed PNX CHG-3617 parts

Grease compatible with plastic gears

Fasteners

NEMA17 Motor to Gearbox

For the standard assembly without a rubber pad:

M3 × 8 mm hex socket countersunk screws

If a rubber pad is placed between the motor face and the gearbox mounting surface:

M3 × 12 mm hex socket countersunk screws

Use the M3 × 12 mm screws only when the additional rubber pad thickness is present.

Heat-Set Inserts

For all designated large insert holes except the motor mounting section:

M3 × 5 mm heat-set threaded inserts

Lower Gearbox to Upper Gearbox

Use:

M3 × 15 mm hex socket countersunk screws

Output Gear to Output Bearing Part

Use:

M3 × 8 mm hex socket countersunk screws

Recommended Printing Settings

Gears

The gears directly affect gearbox operation, so they should be printed more precisely than the housing parts.

Recommended settings:

Material: PETG

Nozzle: 0.4 mm

Layer height: approximately 0.20 mm

Use sufficient perimeters/walls

After printing, inspect the gears for:

stringing

burrs

elephant foot

over-extrusion

debris between teeth

warping

deformation around center holes

Even small strings or protrusions between teeth can increase resistance after assembly.

Housing and Larger Structural Parts

Larger structural parts can be printed with a larger nozzle.

Example settings:

Material: PETG

Nozzle: 0.6 mm

Layer height: approximately 0.30 mm

Use sufficient perimeters/walls

Bearing seats, insert holes, and motor mounting features may print differently depending on the machine, so verify the actual printed dimensions before final assembly.

Assembly Procedure

1. Install the M3 × 5 mm Heat-Set Inserts

Before starting the mechanical assembly, install M3 × 5 mm heat-set threaded inserts into all designated large insert holes except the motor mounting section.

Install each insert as perpendicular to the surface as possible.

Check the following:

the insert is not tilted

the insert is not pushed too deep

the insert does not protrude excessively above the mating surface

the surrounding PETG is not excessively melted or deformed

an M3 screw can be threaded into the insert correctly after installation

Do not install M3 × 5 mm heat-set inserts in the motor mounting section.

2. Attach the Input Sun Gear to the NEMA17 Motor Shaft

Install the 12T input sun gear onto the NEMA17 motor shaft.

Make sure the sun gear is not tilted or mounted eccentrically.

Input-sun eccentricity can cause uneven meshing with the three compound planets, increased vibration, noise, and rotational resistance.

3. Attach the NEMA17 Motor to the Lower Gearbox

Mount the NEMA17 motor, with the input sun gear already installed, to the lower gearbox section.

Standard Assembly

Use:

M3 × 8 mm hex socket countersunk screws

When Using a Rubber Pad

If a rubber pad is placed between the motor face and the gearbox mounting surface, use the longer:

M3 × 12 mm hex socket countersunk screws

The longer screws are required because of the additional thickness of the rubber pad.

Do not fully tighten one screw first. Tighten the screws gradually in an alternating pattern so that the motor remains square to the gearbox.

After tightening, confirm that the input sun gear remains correctly centered in the gear train.

4. Mark the Three Planet Positions at 120° Intervals

Before installing the compound planet gears, mark three positions at 120° intervals using a permanent marker, paint marker, or similar marking tool.

These marks are used as reference points to position the three compound planet gears evenly and improve assembly alignment.

Do not rely only on visual estimation. Marking the three locations first makes it easier to keep the planet positions consistent during assembly.

5. Install the Three Compound Planet Gears

Install the three compound planet gears using the 120° reference marks made in the previous step.

Each compound planet should mesh naturally with the input sun gear and the surrounding ring gear geometry.

Do not force a planet into place if one gear is noticeably tighter than the others.

Check:

the 120° reference marks

equal planet spacing

burrs or strings on the gear teeth

elephant-foot deformation

dimensional print errors

input-sun eccentricity

overall planet alignment

After all three planets are installed, move them by hand and confirm that the gear engagement feels natural.

6. Install the Upper Sun Gear

After the three compound planet gears are correctly positioned, install the upper sun gear in the center.

The upper sun gear must engage with all three compound planets simultaneously.

Do not force one side into position. Slightly adjust the three planets as necessary until the upper sun gear seats naturally.

After installation, confirm that the upper sun gear and all three compound planets can move as intended.

7. Install the Output Bearing

Install the 30 × 42 × 7 mm ball bearing into the upper output bearing part.

Do not force the bearing into the seat while it is tilted.

Confirm that the bearing is fully and correctly seated in its intended position.

8. Join the Output Gear and Output Bearing Part

Attach the output gear to the output bearing part using:

M3 × 8 mm hex socket countersunk screws

First start all screws lightly to align the parts.

Then tighten the screws gradually in an alternating or opposing pattern.

Check that:

each countersunk screw seats correctly

the output gear and bearing part remain aligned

the PETG is not deformed by excessive tightening

This joint is an important torque-transmitting connection, so make sure every required screw is installed and properly seated.

After fastening, check that the output section rotates smoothly.

9. Apply Grease to the Gear Teeth

Before closing the gearbox, verify that the gears mesh correctly and apply grease to the active tooth surfaces.

Use a lubricant that is chemically compatible with PETG or the plastic material used.

There is no need to completely fill the gearbox cavity with grease.

Apply enough lubricant to create an even coating over the active gear teeth.

10. Join the Lower and Upper Gearbox Assemblies

Join the completed lower motor/gear assembly with the upper output/bearing assembly.

Align the gear train and center positions carefully so that the two halves come together without excessive force.

Use:

M3 × 15 mm hex socket countersunk screws

to fasten the upper and lower gearbox sections.

Recommended tightening procedure:

Start all M3 × 15 mm screws lightly.

Do not fully tighten one screw first.

Tighten opposing or alternating screws gradually.

Check that the gap between the upper and lower sections closes evenly.

Perform the final tightening only after the assemblies are fully seated.

Excessive screw torque can distort the PETG housing and change the gear center distance, increasing rotational resistance.

Final Fastener Inspection

After assembly, recheck all fasteners and inserts.

Verify:

M3 × 8 mm hex socket countersunk screws at the motor mounting section

M3 × 12 mm hex socket countersunk screws if a rubber pad is used

M3 × 8 mm hex socket countersunk screws between the output gear and output bearing part

M3 × 15 mm hex socket countersunk screws joining the upper and lower gearbox sections

all M3 × 5 mm heat-set threaded inserts

Make sure no screw is loose and no heat-set insert rotates or pulls out.

Manual Rotation Check After Assembly

Before applying motor power, rotate the gearbox manually through several revolutions.

Check that:

all three compound planet gears rotate correctly

the planets remain positioned at the intended 120° locations

there is no repeated binding at a specific angle

the input sun gear remains centered

the upper sun gear meshes correctly

the output section rotates smoothly

the bearing does not move inside its seat

screw heads or screw ends do not interfere with the internal gears

heat-set inserts do not rotate or pull out

there is no abnormal gap between the upper and lower housing sections

Only begin powered testing after smooth manual rotation has been confirmed.

Initial Powered Testing

Do not begin with maximum speed or heavy load.

A recommended test sequence is:

No-load low-speed rotation

→ Forward and reverse rotation

→ Gradual speed increase

→ Backlash and noise check

→ Gear and bearing temperature check

→ Light-load test

→ Robot-link load test

The 36:1 reduction ratio can be checked approximately by confirming that about 36 input revolutions produce about 1 output revolution.

Important Notes

1. Mark the Planet Positions at 120° Before Installation

This is one of the most important assembly steps.

Before installing the three compound planet gears, mark three locations at 120° intervals using a permanent marker or similar marking tool, and install the planets according to those reference marks.

Poor alignment can cause one side of the gear train to mesh too tightly or increase rotational resistance after assembly.

2. Use the Correct Motor Screw Length

Without a rubber pad:

M3 × 8 mm hex socket countersunk screws

With a rubber pad between the motor and gearbox:

M3 × 12 mm hex socket countersunk screws

Do not mix up these two screw lengths.

3. Heat-Set Insert Locations

Do not install M3 × 5 mm heat-set inserts in the motor mounting section.

Install the M3 × 5 mm inserts only in the other designated large insert holes.

4. Use the Specified Screw Lengths

Using screws that are longer than specified may allow the screw ends to protrude into the gearbox and interfere with internal gears or rotating parts.

Always check for internal interference after assembly.

5. Do Not Overtighten Screws

Excessive tightening can damage or distort PETG parts.

Possible problems include:

cracking around heat-set inserts

deformation of fastening areas

bearing-seat distortion

housing misalignment

changes in gear center distance

output-part deformation

Countersunk screws can generate wedging forces in the surrounding plastic, so do not apply unnecessary tightening torque.

6. Bearing Installation

Do not force the 30 × 42 × 7 mm output bearing into the seat while it is tilted.

After assembly, verify that the rotating output components do not continuously rub against the bearing outer race or shield.

7. FDM Dimensional Tolerance

This model is designed for FDM manufacturing, but identical dimensions cannot be guaranteed on every printer.

Pay particular attention to:

bearing seats

motor shaft holes

gear mesh clearance

M3 × 5 mm insert holes

M3 screw through-holes

motor mounting features

output mounting surfaces

If necessary, modify the supplied STEP file to match the dimensional behavior of your own printer.

8. Robot Application

Actual allowable link length and payload cannot be determined from the reduction ratio alone.

Performance will also depend on:

filament type

print orientation

layer adhesion

printer dimensional accuracy

gear tooth quality

bearing quality

heat-set insert installation

screw fastening

link length

joint acceleration

impact loads

operating temperature

Perform sufficient no-load and progressive load testing before installing the gearbox in a complete robot.

Included Files and Drawings

The uploaded package includes files for manufacturing, modification, and integration with other robot structures.

printable 3D models

complete gearbox STEP assembly

output-side mounting reference drawing

motor-side and lower-gearbox mounting reference drawing

major dimension reference images

Separate drawings show where the output should be attached to a robot link and where the NEMA17 motor and lower gearbox section should be attached to another structure.

Use these drawings when designing robot links, joint frames, motor brackets, or custom adapters.

For the most accurate dimensions, import the STEP file directly into CAD and measure the required geometry.

Project Purpose

PNX CHG-3617 is intended as a modular FDM robot-joint gearbox that can be manufactured, disassembled, modified, repaired, and reprinted using common 3D-printing equipment and standard hardware.

Actual performance will depend on the printer, filament, dimensional tolerances, lubrication, assembly quality, screw fastening, and applied load.

Perform sufficient testing after printing and adapt the gearbox to the requirements of your own robot structure and operating conditions.

Tagi