1 / 3
Modified Extended Set of Wooden Train Track with 50+ Unique Pieces — zdjęcie 1
1 / 3

Modified Extended Set of Wooden Train Track with 50+ Unique Pieces

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

I modified the connections of Extended Set of Wooden Train Track to better fit IKEA/Brio pieces

Ocena
0 / 5
Polubienia
17
Pobrania
58
Wydruki
0
Wyświetlenia
309
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Building Toys
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

I found the amazing Extended Set of Wooden Train Track with 50+ Unique Pieces set of Michal Fanta and in my enthousiasm, I immediately printed the X Star Switch, the biggest piece. Only the find out that it wouldn't fit my IKEA/Brio mix of tracks, which was a bummer.  The main problem is that the male connector of the IKEA piece and female printed piece connection is too tight. It will require considerable force to join them together. Therefore, I modified the pieces in the set to make sure that the pieces:

  • Connect to IKEA and Brio pieces;

  • Connect to the original printed pieces.

The fit with IKEA/Brio pieces is nicely loose, but not too loose in my opinion. The connection between male-modified and female-original is flush, but not tight. Tolerances might vary a bit depending on nozzle and printer, etc. I tested only with the Core One + with the 0,4 mm nozzle.

I didn't modify the bridge pieces, because I couldn't find existing IKEA/Brio pieces that would connect to these pieces. Also,  modifying anything not-flat is a PITA in TinkerCAD.

Test before you print

To make sure which version connects the best with your track pieces, I advice you to print the following piece from both the original and the modified sets:

  • A3_Reduction_Micro_Straight_Track

This piece is very small and contains both a male and female connection to test on your pieces.

Known Issues

Unfortunatly I found out about another issue. The double tracks and switches are based on two rail pieces put snugly together, but the wooden pieces are a bit wider than that. The printed double track won't fit on a wooden switch for example. You have to add two single tracks between to make it fit, see the added pictures.

Modified Pieces

  • Straight Tracks

    • Medium Straight Track - A

    • Short Straight Track - A1

    • Mini Straight Track - A2

    • Reduction Straight Track - A3

    • Mini Straight Track - B2

    • Mini Straight Track - C2

    • Straight Track - D

    • Double Straight Track - K1

    • Buffer Stop Track - S

    • Buffer Stop Track - R

    • Start Straight Track - V

    • Start Straight Track - U

  • Curved Tracks

    • Curved Track - E

    • Short Curved Track - E1

    • Double Curved Track - EE

    • Double Short Curved Track - EE1

    • Z Track

  • Switches

    • Switching Track - F

    • Switching Track - G

    • Parallel Switches - F1

    • Parallel Switches - G1

    • Three-Way Parallel Switches - F2

    • Parallel Switches - G2

    • Curved Switching Track - L

    • Mechanical Curved Switching Track - L1

    • Curved Switching Track - M

    • Mechanical Curved Switching Track - M1

    • Double Curved Switching Track - I

    • Double Curved Switching Track - J

    • Switching and Crossing Track - K

    • Short Curved Switching Track - O

    • Short Curved Switching Track - P

    • Short Curved Switching Track - O1

    • Short Curved Switching Track - P1

    • Short Curved Switching Track - O2

    • Short Curved Switching Track - P2

    • T Switch Track - T

    • Two Way Parallel Switches - Y1

    • Two Way Parallel Switches - Y2

    • Star Switch Track - X

    • Roundabout Switching - X1

    • Roundabout Switching - X2

  • Crossing

    • Crossing Track - H

    • Crossing Track - H1

    • Criss-cross Track - H2

    • Curved Crossing Track - H3

    • Criss-cross Track - H4

    • Curved Crossing Track - H5

  • Viaducts and Bridges

    • Ascending Track - W1

    • Descending Track - W2

    • Bridge Track - W9

Unmodified Pieces

Please download the following files from the original set if you need them:

  • Switches

    • Mechanical Curved Switching Track - L1 - Part 2

    • Mechanical Curved Switching Track - M1 - Part 2

  • Viaducts and Bridges

    • Viaduct Track - W3

    • Curved Viaduct Track - W4

    • Curved Viaduct Track - W5

    • Bridge Track - W9b Bridge Truss Girder

    • Bridge Track - W9c Bridge Truss Girder

    • High Viaduct Track - W10

Updates

  • 2026-08-16: Found out (by printing the X-star-Switch, again, that piece seems cursed or something xD) that I used the wrong template for the male connector. The connection with the original printed pieces were too tight, should be better now

  • 2026-08-21: Found out that the printed double track won't fit on wooden pieces, added a 'Known Issues' tab while working on this

Tagi