Cyclo Planter — Vietnamese xích lô succulent pot that rolls
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Vietnamese cyclo as a rolling succulent planter. Seat = pot, footboard = drip tray, rack = 3 cuttings cups. 9 STLs, all
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 25
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Decor
- Licencja
- Creative Commons — Attribution
A Vietnamese cyclo (xích lô) reimagined as a little rolling planter. The passenger seat is the pot, the footboard is a drip tray, and the driver's back rack carries three cups for cuttings or single stems. The three spoked wheels really roll, the cranks snap onto the fork, and the folded hood bow behind the seat is the driver's handlebar — and a trellis for a climber.
Every joint is a snap, not a friction press: split pins with barbs click into pockets, so a light push seats each part and it stays. 9 STLs, 16 pieces, no glue, no hardware, no supports. ~105 g of PLA as sliced.

What it holds
Pot — 63 × 55 mm at the rim, 57 × 49 at the floor, 40 mm deep, ~130 ml. A Ø50 tapered nursery pot drops straight in, or plant into it directly. Three Ø4 drains run from the pot floor into the footboard tray (~6 ml).
Rack — three Ø13 × 27 mm cups behind the driver's saddle. Water for cuttings, or single stems.
Trellis — the two rungs in the hood bow are there for a climber.
Overall 164 mm long, 96 mm wide over the hub caps, 109 mm to the top of the bow.

Two honest notes from the printed one
The snaps hold, but they are snaps. Every joint clicks home and stays put in normal handling — but a hub cap, a fender or a crank is held by two 0.25 mm barbs, not by glue. Knock one hard sideways, or pick the model up by a fender, and that part can pop back off. It is not damage: line the pegs up and push it straight back in, and it clicks again exactly as it did the first time. If you want a display piece that never comes apart, a drop of CA in the cap recess and on the fender pegs settles it permanently.
The wheels spin, and they can spin better. Straight off the plate they run free on the Ø5 axles with 0.5 mm of running clearance and about 1 mm of end play, and the cyclo rolls across a desk. What you get is an honest printed bearing, not a smooth one — expect a little rumble and a touch of wobble. Two minutes of work fixes most of it: spin each wheel back and forth by hand to bed the bore in, and if one still drags, run a Ø5 drill bit through the wheel bore by hand (never the boss — the split fingers are the part that is meant to give). A wipe of dry PTFE or a graphite pencil rubbed into the bore is the finishing touch.
All parts print as exported, 0.2 mm layers, 3 walls, 15 % infill, no supports, no pause. The body prints upright on its flat underside; the rear fender arch bridges 13 mm and the inside of the arch is hidden by the wheel. Two colours look right — body in one, wheels + fenders + caps + cranks + bow in another (all separate parts, no AMS needed). The photos above are six colours because every piece is its own part; use as few or as many as you like.
STL | qty | orientation |
| 1 | as exported, upright (164 × 66 × 73 mm) |
| 3 | outer face down |
| 2 | lying on its 0.3 mm flat, slot standing vertical |
| 1 | lying, same |
| 4 | flat face down, bore at the bed |
| 2 | outer side face down, pegs up (same part both sides) |
| 1 | flat |
| 1 + 1 | chainring / arm face down |
The one thing worth checking on the plate: each fender peg is split by a 1.2 mm slot that must come out open. If your slicer bridges it, the peg is solid again and it will break instead of clicking.
Assembly — 11 steps, every one a click

Step 1 — Body. Every bore is Ø5.2 or Ø4.2, a clearance over its pin. If an axle will not slide freely into a boss before the barbs reach the lip, deburr the mouth with a Ø5 bit turned by hand.

Step 2 — Rear wheel. Drop it between the fork prongs, hub centred on the bore (0.6 mm each side).

Step 3 — Rear axle. Push axle_rear through prong → wheel → prong. It slides; the barbs squeeze through each bore and the axle ends up proud by 5.6 mm on both sides. Centre it. Do this before the caps — a capped rear axle cannot be threaded through the prongs.

Step 4 — Rear hub caps (×2). Push a cap over each split tip, flat face toward the prong, until it clicks: the barbs open into the recess in the dome and the tip shows flush like a hub nut. Hold the first cap firmly while you push the second.

Step 5 — Front axles (×2). Push either end of an axle_front into each side boss until it clicks, 5.6 mm in. Both ends are the same.

Step 6 — Front wheels (×2). Slide a wheel onto each axle with the proud hub face inward, toward the tub. It should spin free with about 1 mm of end play.

Step 7 — Front hub caps (×2). Push a cap over each front tip until it clicks. The barbs set where the cap sits, so the 1 mm of end play stays — that play is by design, not slop.

Step 8 — Fenders (×2). Two split Ø5 pegs into the two pads beside each front wheel; push straight in until both click. Each barb flexes 0.2 mm into its own slot, so the arc does not have to spread and it does not matter how you hold the fender — but push on the arc directly over the pegs, not on the crown. The part is symmetric: the same STL serves both sides, turned over. If it will not start, the pegs are not both lined up — walk it in one peg at a time, then square it up. Never force it.

Step 9 — Hood bow. The two split pegs into the brackets behind the seat back; push until they click on the socket floor. It leans back 12° and its legs sit flat on the bracket tops. Grips outward — that is the driver's handlebar, and the two rungs are the trellis.

Step 10 — Right crank. Push crank_r (the chainring side) onto the split peg on the right prong until it clicks, arm pointing forward. The peg's tip shows in the recess on the hub's outer face. Push on the hub, not on the arm — the arm is the thinnest thing in your hand. The first 2.9 mm of the 5.1 mm stroke is free travel, then it resists for the last 2 mm as the barbs squeeze, then it clicks. If it fights you from the moment it touches the peg, the peg is drooped or stringy: clean the slot out and break its underside edge with a knife rather than pushing harder.

Viewed from the right rear, so the chainring is not hidden behind the body.
Step 11 — Left crank. Push crank_l onto the left peg until it clicks, arm pointing back — the cranks sit 180° apart.

Viewed from the left, the opposite side to step 10: the two cranks sit on opposite faces of the rear fork, so no single view shows both.
Gotchas
Tight wheel? The bore is Ø5.5 over a Ø5 axle. If a wheel drags, ream the wheel bore, never the boss.
No click? The barbs are 0.25 mm; a bore that printed small needs a firmer push, not a bigger bore. If a finger does shear off, print another axle — they are 1 g each.
Fender on the wrong side shows immediately: the pegs will not line up with both pads. Turn it over.
Do not drill extra drains. Three Ø4 drains already run from the pot floor into the footboard tray.
Water and PLA are fine on a windowsill. If it lives outdoors, print it in PETG.
Tuning
Every dimension is a named variable at the top of the included cyclo_planter.scad — barb, clr, wheel_clr, pot_w, cup_id. Want a tighter or looser snap, a bigger pot, deeper cups? Change one number and re-export.
Designed from scratch in OpenSCAD for the Custom Cyclo Challenge — no AI, no scanned or generated geometry, every surface is code.
