Liczymy pasujące modele…
Cyclone dust collector. Can be printed in two parts on the Prusa Mini! Bouth parts have a rim to be fitted together neatly. PrusaSlicer Files have all the necessary supports!
Cyclone dust collector for a 2.5" hose. Made to be as large as could be on a Prusa i3 mk3s. I used m3 hardware to put the top and bottom together but glue would work just as well. ¼-20's for attachment to the bucket. I put this on top of…
This is a marble machine with a lift that lifts three (or more) marbles simultaneously, and releases them to three separate tracks. Two of those tracks are connected in series, so a marble will therefore alternate between those tracks.…
Cyclo valve cover for 6 and 8 mm valves I recommend putting a collar around the valves so that they hold well on the printing plate
January 31-2025 Version 4.1 released! Version 4.1 is released! minor mods and tweaks! November 26- 2024 Version 4 release! (note - v3 and v4 lower cone is the same(NOT V4.1!!) , only the upper inlet/outlet section is new so you can reuse…
This construction is a logical continuation of one of the first options. The community likes it, apparently because of its low profile. It seems more stable. Our friend Der_Rudi asked to increase the gap for better throughput. Now it's…
Have you ever wanted draw repeating geometric patterns at any time in any place? No? Well, let's pretend you did... This handheld print conveniently combines a drawing platform with a case for the gears and paper. It easily fits into a…
Cyclodial Gearbox 40:1 with Tarot 4108 BLDC and CUI AMT102 capacitive encoder. Video assembly instruction available! Mounting instructions for the encoder There are also instructions on how to change the gearbox ratio...…
Version 3- new, even bigger and better cyclone dust separator! This is still a beta! thou it is fully functional! Assembly info and such will be added later, newer versions of the top cap may get uploaded ** note- will need a 300mm build…
This is a rework of my own model from thingiverse (from 2012). “cyclone to catch the spray while purging/cleaning an airbrush.” There may be some sputtering especially with airbrush nozzles bigger than 0.2mm. Prints without supports, a…
Cyclops Guide by ModBot ( Thank you for the great video ) Latest Update 22 September 2024: -Version 1.9.1 with better tolerance -PTFE tube connector -stronger tension arm ----------- Exciting News: Cyclops Extruder is Now in Open Beta!…
⚡ CLICKFLOW – IMPORTANT INFO 🔧 Assembly Note: This model was tested using a blue mechanical keyboard switch . For a more secure and durable assembly, I recommend using a small amount of glue on the connecting parts to keep everything…
I designed this gearbox after reading some papers online. A video showing the gearbox being built and tested can be found here: https://www.youtube.com/watch?v=IKkw4d7jyu0 More information as well as a hardware list can be found in the…
Also called a “Cyclone Dust Separator” or “Dust Collector”, I needed one but the ones available were too expensive. I printed it with PETG. I am not sure if PLA will work. The print is huge and uses up a substantial amount of filament.…
This is a wall mount for a Shark hand held vacuum with a charge port. This should fit the following models CH901, CH950, CH951, and CH955. I was surprised to find that this model does not come with the wall mount, same issue with the more…
This is an updated version of my older visor. Sleeker, and more akin to the 90s television show
This is a 3d model of the cyclops submarine seen in Subnautica. It was designed to be assembled as a kit, however since I have very limited experience with making printed parts fit, some glue could be required (I used some for several…
Want to access even more models not found here? Interested in supporting my efforts making free models for the world to enjoy? Check out my patreon page here: https://www.patreon.com/mz4250 Patrons have access to all my files in one…
Need a custom adapter for your cyclone separator? Comment the required inlet and outlet dimensions and I’ll make and upload it for you. This 3D-printable cyclone separator efficiently removes dust and debris from your vacuum system —…
I made this cyclone separator. It consists of five parts, four of which were 3D printed. The last, the top piece, was made out of acrylic on my CNC router so I could see inside but it can also be 3d printed. In my test it worked…
Universal cyclon for vacuum cleaner. Can be attached to any container. Use a 250mm long drain pipe diameter 50mm in the center. Use screws for attachment. Make sure you seal the cyclon to the container.
Check out a video about my project! I tried to use 3D printing to speed up production on a laser cutter. A simple cyclone separator that can be easily printed within 20 hours saves you money on bags and works amazingly well!
A one-eyed fella. Bad at judging distance. Suitable for 28mm tabletop games. Created so that it does not need any supports and prints well on a cheap FDM 3d printer like the Ender 3. NOTE Other models seen in the images are available on…
Cyclone dust collector for 100mm hose diameter. Print and bond the 4 parts together A mesh structure has been added to the cyclone3 component to prevent large debris from being sucked in. Please download according to your preference…
small fine mist sprayer ∅8mm connector (with ½" adapter)
This is a visor inspired by Cyclops's visor in the X-Men comics. It wraps around the face and there are supports to help it rest on your ears. This was made to match my face so you may need to make adjustments to fit your own face as…
Cyclone Seperator for Festool Vacuums This is my custom version of a cyclone seperator for Festool vacuum cleaners. The goal was to build my own, cheaper version of Festools CT-VA-20, while maintaining the core functionality without…
For experienced makers. Remember this is a free file. Ready to get your socks sucked off? This is a handy dandy, print-it-yourself cyclone! If you are looking to upgrade your dust collection system, we highly recommend giving this design…
After repeated trial shooting, stars sometimes blur at 60 sec exposure with auto guide. 30 sec or less, stars are stable and appear as dots. Consistently good results are obtained with live stacking of 30 seconds or less. Upload photos of…
Want fine water spray but can't print a fine nozzle? This is using centrifugal forces from a cyclone to nebulize water so it can be printed. I recommend using PET-G as there is some water pressure involved - please use caution! 8mm ∅…
Recently I have recently got into Gridfinity world and I'm amazed. Super easy to print and even easier to user and organize you stuff. I have also discovered a fantastic plugin for Fusion 360 called “Gridfinity Generator” that makes even…
The EIBOS Cyclopes is about as good a filament dryer as you can get these days, but it has a major flaw - the filament rolls are too close to the heat source and they will scorch. Some, including myself, have attempted to solve this…
My Educational Mechanical Examples Series This model is one of my educational mechanical mechanism examples on 80mm x 80mm base plates. You can find all models in the series in this collection => [Mechanical Mechanism Examples] This model…
Cyclone Dust Collector The Dust collector main body fits perfect on a Prusa MK3 Printbed. Update 03.03.2025: Os Vac Neo M32 Intake and Outlet Adapter Update 25.01.2025: Os Vac Neo F32 Intake and Outlet Adapter 35mm, and 38mm outer…
Das ist ein Unterdruckventil für einen Zyklonabscheider. Es kann mit Hilfe der Feder eingestellt werden und verhindert das implodieren eures Sammelfasses. This is a vacuum valve for a cyclone separator. It can be adjusted by means of the…
This 3D-printed model showcases an 11:1 cycloidal drive, featuring 11 lobes on the disk and 12 pins of the housing. The disk was generated with the following parameters: R = 45 mm (radius of roller pin ring) Rr = 5 mm (radius of roller…
A Cycloidal Gearbox with a 20:1 reduction ratio, for driving just about anything. I haven't tested the force output yet, but it nearly broke my finger when trying to hold the output. Feel free to modify the motor bolt pattern for your…
This is a parametric dust extractor designed with a small shop in mind! The included STLs are ready for a 45mm hose and mount to the dust bin via 6, 5mm bolts.
In English: Model Cyclops from Subnautica. There are three types of models of Cyclops itself. 1. Cyclops_with_cockpit is a Cyclops with the original cockpit. 2. Cyslops_whitout_cocpit is a Cyclops with the cockpit removed for ease of…
Inspired by the Nextruder gearbox, I created this visualizer. The extruder indicator looks very similar to a cycloid gearbox, although it is actually only a half one. Google it, it's an interesting concept! The middle part rotates…
M48 Cyclone Spiral Boot Knife Knife inspired by the M48 Cyclone, featuring two interchangeable blades with a three-cut spiral design. The sheath can be used as an additional handle, resulting in two Cyclone knives.
Created as a physical representation of nested hypocycloids . The .gcode was generated with the model scaled to 75% because it makes it a nicer size for fidgeting. If the nested version comes out fused together, you can download the…
osVAC conversion adapters for Dust Commander cyclone dust separator. With these adapters you can attach osVAC hoses directly to the Dust Commander. Also check out my osVAC pressure relief valve adapter. The female connector uses my osVAC…
Small cyclone separato for 35mm vacuum cleaner tube. Use tape to glue the two parts together. Supports only on build plate for top part. No support for buttom part. Print Settings Printer Brand: MK3 Printer: Prusa i3 Supports: Yes…
Use super glue to connect the top and bottom of the cone. The nozzle is glued to the bottom of the cyclone. Nuts and bolts attach the parts together. The bottom of the cone and the plate go on opposite sides of a 5 gallon bucket.
Simply chuck the controller on this stand and it should align itself for charging 99% of the time. A minimalistic controller stand for the GameSir Cyclone 2. The geometry of the stand should make it easier to align the controller with the…
Paired with a cheap ebay cyclone dust extractor and a 30 litre bucket, my little Kaercher WD2 vacuum handles the sawdust and chips from my power tools handily. But I found that when I was using it for cleaning up, if I was careless about…
Its here, Version 2 of the cycloidal reducer! All the hardware is the same from the original version, however every printed part has been redesigned! Here are the current improvements over the original: It is now easier to print and…
I really liked the exosuits from nostalgic robotech cyclones. So I just tinkercaded them with lucky13's easy skins. It was fun, but time consuming. And I haven't finished the legs yet. So maybe in the summer. Also, I normally print this…
Dust cyclone for use with a shop vac. Prints in 3 parts. Press fit together. Small cutout in the base to allow room to fit an anti crush valve in the lid of the bucket when you mount the cyclone.
You attach the bands by pushing a looped end into the slot from the side and locking it with a piece of filament through the center of the loop. Print in 0.15mm with 5 perimeters and 13 top/bottom layers. I used different infill…
This model is based on the eccentric cycloidal drive. for this model you would need: 4x 608 bearings(the same ones that are in fidget spinners and skate board wheels). 2x m3 screws that are no more than 30mm long. and all 5 of the printed…
This is a print to increase the surface area on the bucket the cyclone is attached to. This creates more stability.
Updates: Rollerdisk2 contains four M5 mounting locations ana d new Rollercover design This compact cycloidal gearbox is specifically designed for NEMA 17 stepper motors. Assembly requires M3 bolts M5 heat sink 3×15 mm dowel pins two…
Cyclops Bust. Recomendado imprimir con +/- 10 cm de altura.
Cyclodial Gearbox 40:1 with Tarot 4108 BLDC and CUI AMT102 capacitive encoder. Video assembly instruction available! This is an upgrade to my existing gearbox design……
TL;DR: Sub 5 micrometer dust particle separation cut-off (density at or greater than water) Minimal pressure drop with little or no practical effect on suction power 3D-printable with only one support FreeCAD design files and OpenFOAM…
Cyclone is made from 5 parts. mainly to split printing and eliminat as much supports as possible. You have also model where Main body is connected with the PIPE. Last file added is ALL IN ONE - full model of cyclon + one upgrade pipe…
This model can be put together without any hardware, you can use some glue if you want but it's not necessary. The case screws together and might be difficult to get on depending on the print quality. Try using a little lubricant, that…
Follow us on Patreon & Instagram for the latest models. ❱ Instagram: https://www.instagram.com/sektor7_studios_3d/ ❱ Patreon: https://www.patreon.com/sektor7_studios (commercial license & more beautiful designs) Hello everyone :) Today we…
This cycloidal gearbox is meant for Nema 17 motors and uses 2 6903RS bearings. This gearbox is smooth but will give noticeable backlash after much use. It is a 20:1 gearbox which means it gives 20 times the torque but 20 times less speed.
This was printed with a .2mm layer height with 5% infill. Vase mode will not work.
My remix of mgx's variant of the cyclone dust scrubber, adding the possibility to define different sizes for the inlet and outlet. I also added a thread for the standard european PET water bottles (thread from Necks & Caps Library by…
I only really use the crevice tool with my Shark Ultracyclone vacuum, and wanted something a bit narrower than DASMK3S's model that still kept the feature of the built-in charge connector. I use this bracket to mount my Shark Ultracyclone…
Cyclone dust filter and adapter for 110 tube
For the original design I liked the compact size and how it is inline for making it a part of a vacuum (Genius), but wanted the CAD files so rebuilt it as best I could. Tried to simplify the geometry and maximize areas while thickening…
Want to access even more models not found here? Interested in supporting my efforts making free models for the world to enjoy? Check out my patreon page here: https://www.patreon.com/mz4250 Patrons have access to all my files in one…
Simple handle for EIBOS Cyclopes dryer lid. Easier manipulation, less fingerprints on acrylic. Mount with two 20 mm M3 socket head cap screws and corresponding nuts. See attached images. For best strength, speed and print quality print…
3D model of a thargoid interceptor of cyclops/basilisk variant (the geometry of the two is basically the same, they mostly vary in color in-game). Model taken directly from the game. All assets are property of Frontier Developments!! I…
The Eibos Cyclops filament dryer has an inherent design problem. Because the heater is directly below the filament spools when the heater heats up to temp it may overheat the filament to the point that the filament fuses to itself. Eibos…
Use this cyclone dust separator to collect large amounts of dust (e.g. sawdust) in a bucket while keeping your vacuum filter clean. Very helpful in a workshop! The idea is that particles are sucked into the cone, get slowed down by…
This compound cycloidal drive is designed for 35mm "tin can"-style stepper motors. It has two stages, yielding a 49:1 drive reduction. The flat package and integral slew bearing (using 6mm dia. Airsoft BB's) on the output plate make it…
After replacing my home made dust collector with a Dust Deputy cyclone, I found that the plastic barrel I was using would collapse on itself if the hose ended up clogged/blocked. I needed a way to let off the vacuum pressure in these…
This is an open source 3D printed cycloidal gearbox with transmission ratio of 24:1. Made out of 3 disks which engages metal rods and driven by a Nema 17 stepper motor. It's a part of a robotic arm project with a big community behind it,…
Print in place cycloid gearbox fidget
I have a small Stepcraft CNC router in my house and to keep the noise down I use a small Miele cannister vacuum cleaner with a bag and a secondary HEPA filter on a low noise setting to capture the dust and particles from cutting. I needed…
3D model cyklonového separátoru pro vysavač z Aliexpress, Temu a podobného tržiště. Model SN50T3 s průměrem hadic 50mm, který je překreslen podle originálního zakoupeného kusu na Aliexpresu. Model je bez spodní příruby.
Hello, If you like this Thing please leave a like and let me know :-) I remixed a Cyclone for the OSVAC System. Thanks to Hobbyhimmel for the great OSVAC Projekt. For the VAC i used a female adapter to easier Print, but you can place a…
Small cycloidal gear box 14:1 only 10mm tall 10mm output shaft BOM M3 x 16 x 4 M3 x 6 x 2 S6800 Bearing x 1 Nema 17 x 1 Update 11/23/25 Added STEP files
This is an example of an idea I've had floating in my mind for a few weeks now, having seen people make eccentric cycloid gears for robot joints on youtube. I thought they might make quite effective printed bearings, because they only…
This is a design for a metric watertight arcrylic cylinder (90/84 mm) which fits the Cyclops R/C Submarine https://www.thingiverse.com/thing:4560120 by Robert Cook. Modifications Additionaly to the two O-Rings on each cap it is possible…
Vent plugs for the top of the container to control air flow to manage dryer temp. Two parts and outer assembly to block all outer vent holes and the inner can be completely remove or lift and turn.
The original model was split in 2 parts, which is not necessary, if you have a 300mm printbed. Also, the original is a little too short, so that the eibos lid fits only with force. I added 1mm of length and chamfered the top part. Lastly,…
"Don’t anybody move!… I lost my contact lens.” This is the X-Men Cyclops Goggles designed by me for a costume party. They print out nicely in 4 pieces, which I did on my 'Up! Plus 2' 3D printer using the 0.2mm layer thickness. I've added…
Whoever uploads a make of my updated armor first, I will use their pictures in the new model cover! For the first model, When plating this model on the slicer, adjust or change the orientation of the forearms And Lower Legs, so that they…
a 2 stage 20:1 Cycloid Gearbox that's designed in Fusion360 and 3D printed on bambu A1 mini. The motor is a NEMA17. bearings: 40X52X7 2pc 12X18X4 4pc 5X9X3 12pc
TOOLS NEEDED: 3D printer (obviously) Soldering Iron (Hot glue gun can work) Screwdriver Hot glue gun (or just any kind of glue) PARTS NEEDED: Motor : https://www.amazon.com/dp/B08DG2KXZB?ref=ppx_yo2ov_dt_b_fed_asin_title M3 sized wood…
A pressure relief valve is a handy addon that prevents your cyclone dust extractor system from imploding or collapsing, if the hose is blocked e.g. by too much dust or debris. This is a mount for the pressure relief valve from Dust…
mini aca cyclone for use with the Samsung microwave blower motors all parts require supports but the supports on the rotor are optional all hardware for mounting the stator to the motor is included on the motor the rotor is intended to…
There is a new, larger version now- I'm keeping this old version up thou as it's smaller, and a tad easier to print- https://www.printables.com/model/470277-version-3-4100mm-cyclone-dust-separator Update March 29 2022 **V2.5 parts…
This is a cycloidal gearbox for a standard Nema 17 stepper motor designed to be as efficient as possible while maintaining a compact size. The gearbox provides an 8:1 gear reduction. Most of the design is 3D printed, but it uses a number…
20.08.2023 Improved ergonomics. Printer brand: Flying Bear Printer: Ghost6 Rafts:No Supports: Yes Resolution: 0.12 Infill: 20% Filament brand: Esun Filament color: red, signal red Filament material: PLA+ Slicer: Ultimaker Cura 5.4.0 Wall…
Want to access even more models not found here? Interested in supporting my efforts making free models for the world to enjoy? Check out my patreon page here: https://www.patreon.com/mz4250 Patrons have access to all my files in one…
I printed 16 of these to plug all the unused filament and vent ports. The number of openings causes the internal temp to drop to the point where it really wasn't doing much to lower filament humidity.
This is the result of my imagination and guesses. I tried to make the design as suitable as possible for printing on 3d printers. I hope you enjoy it. I will be glad to hear any criticism, preferably objective.
*** Work in progress – hasn't been fully validated yet *** This model is intended to be used in conjunction with a cyclonic dust collector (such as the the Harbor Freight Bauer cyclone, or Oneida Dust Deputy), for use in a woodworking…
Der Adapter für den Schlauchanschluss hat einen Außendurchmesser von 64 mm und auf der Zyklonabscheiderseite einen Innendurchmesser von 55 mm. Er ist geeignet für die Bajonettanschlüsse von Festool, Mafell, Metabo und Starmix. Der Adapter…
A Cyclops perfect for your tabletop game! Print each piece as flat as possible with supports and a brim. This was based off a file I found here: http://www.123dapp.com/123C-3D-Model/Cyclops-with-Large-Rock/768231 . I just modified it and…
Check out version 2 here ! At the moment (6/7/24) it is still in beta, but version 2 is still better in almost every possible way! Reduction specs: 64/1 reduction. NEMA 17 mounting. BOM: 4x M3x25 cap head bolts 2x 10x15x4 bearings 1x…
Not content with the designs already out there, I designed my own cyclone dust collector to achieve the following: print quick and cheap (<400g of filament!) use minimal supports (see ‘Support Deck’ section below) integrate a vacuum…
