Cinebot30 M10 GPS + Dual VTX & ELRS Antenna Mount (Walksnail Moonlight / DJI O4 Pro)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Cinebot30 mount for an M10 GPS, dual VTX antennas (Walksnail Moonlight / DJI O4 Pro) and an ELRS/CRSF antenna.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 6
- Wydruki
- 1
- Wyświetlenia
- 34
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Standard Digital File License
Overview
GPS and dual-antenna mount for the GEPRC Cinebot30. It holds an M10 GPS module and both antennas of a dual-antenna digital VTX (Walksnail Avatar Moonlight or DJI O4 Air Unit Pro), and gives your ELRS / CRSF receiver antenna a pass-through. Mounts with one M3 screw, weighs about 3 g.
I couldn't find a mount for this quad that carried both VTX antennas and the GPS, so I remixed two existing designs.
Features
Fits a GEP-M10 / M8U-size GPS module. It snaps in from below and fits snugly, so it won't fall out.
Two Ø3.5 mm antenna tubes in a V, 33° from vertical, leaning out over the GPS
A full-length slit on the side of each tube: press the antennas in sideways. Moonlight and O4 antennas can't be unplugged and threaded through.
X-slit with a Ø2.2 mm centre hole for the GPS cable. It flexes open to pass a 6-pin connector (8.9 × 2.8 mm).
Ø2.5 mm pass-through for the ELRS / CRSF antenna coax
Single M3 mounting hole for the top frame plate
Size: 46.8 × 24 × 13.2 mm
Check your antennas: the tubes are Ø3.5 mm. Tested with Walksnail Moonlight antennas. DJI O4 Pro antennas should fit similarly, but check before printing. The standard (non-Pro) O4 Air Unit has only one antenna.
Printing
Print flat as oriented. No supports needed; I checked the overhangs, and the only ones are a small GPS retaining lip and short bridges.
TPU recommended, because the GPS ledge and the X-slit are meant to flex.
Use elephant-foot compensation (about 0.1–0.15 mm) and a well-tuned first layer so the thin slits don't fuse shut.
After printing
Antenna tube slits: if the first layer seals the bottom of a slit, snip it away with flush cutters.
GPS X-slit: it usually prints closed. Cut the X open with a hobby knife or flush cutters.
ELRS hole: it's tight for a U.FL connector plus wire. If yours won't fit, open it up with a 3 mm drill bit. The next version will have a bigger hole.
Assembly
Fit the GPS before bolting the mount to the quad, because the GPS goes in from underneath.
Plug the GPS cable into the module. Feed the other connector out through the front opening of the tray, then down through the X-slit.
Push the GPS in from underneath, ceramic patch antenna facing up, until it clicks past the bottom ledge.
Press each VTX antenna into its tube through the side slit.
Feed the ELRS / CRSF antenna through its hole.
Mount it on the quad with the GPS end pointing away from the frame. Fit an M3 screw through the tab into the top frame plate. The hole is about 10 mm deep, so reuse the stock screw or an M3 × 12–16.
Route the cables to the flight controller, VTX and receiver, and tidy them with a zip tie.
Known issues / next version
The ELRS hole is slightly small for a U.FL connector. Push an m3 from top to bottom to slightly widen the hole, and then it works just fine.
The first layer can seal the thin slits. I may add small chamfers at the bottom of the slits.