Dual-band satellite Yagi mounting parts for M1GEO/G8OCV antenna (7/8" dowel boom)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Printable rings, feedpoint and Moxon spacers for the M1GEO/G8OCV 2 m/70 cm satellite Yagi, 22.8 mm boom
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 16
- Wydruki
- 0
- Wyświetlenia
- 108
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Ideas
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
3D-printable mounting parts for the dual-band satellite antenna designed by George Smart, M1GEO/G8OCV: a 2 m Moxon plus a 70 cm Yagi on one boom. The antenna design, element lengths and spacing are his. I only designed the printed hardware. His page: https://www.george-smart.co.uk/antennas/dual_band_satellite_yagi/
Built and working with these parts. SWR was about 1.4 on the 2 m Moxon. Your numbers will depend on your coax, your analyzer and where you measure.
My build uses a wooden dowel boom with a measured 22.8 mm fit (HD sells them as 3/4"), 8 AWG solid bare copper (3.26 mm) for the elements, RG-8X coax, and #6-32 hardware. If your boom isn’t 22.8 mm, the bore size needs to change before you print. Print one test ring on your dowel first.
Files and quantities
1_element_ring ×6 (1 for the 2 m reflector, 5 for the 70 cm elements). Full ring around the boom, the element wire slides through a tunnel in it, and a wood screw locks it in place.
2a_feedpoint_ring_base ×1 and 2b_feedpoint_ring_cap ×1. Print one of each. Solderless: ring terminals clamp the two driven-element halves, and the cap clamps the coax.
3_moxon_dogbone_15mm ×2. Print two. Holds the 15 mm gap between the driven element and reflector tails.
Hardware (not printed)
#6-32 machine screws and nuts for the feedpoint terminals and cap bolts.
#6 pan-head wood screws, 5/8" preferred, to lock the rings to the dowel.
Two #6 ring terminals, for the coax center and braid.
8 AWG solid bare copper wire, and RG-8X coax.
Tools
Small cutters and a ring-terminal crimper.
A drill for pilot holes in the dowel.
Calipers, for checking how the printed rings fit your dowel and wire.
Wire cut list (mm)
Reflector: 700 wide with 150 tails.
Driven element: two halves, each 342 straight plus a 106 tail (700 overall with a 16 mm feed gap).
Yagi (70 cm) elements: 334, 324, 280, 296, 274.
Spacing
Space the element centers (the wire centerlines) as in M1GEO’s schematic, measured from the reflector: 0, 127, 271 (driven element), 293, 477, 719 and 925 mm. The ring is not centered on its wire, so line up the wire tunnel with each mark, not the middle of the ring. The wire tunnel sits about 4.5 mm from one face of each element ring, and in the feedpoint it sits about 14.5 mm from the front face and 24 mm from the rear.
Assembly notes
Ring orientation: I recommend installing every ring the same way, with the wire tunnel side toward the reflector, and sliding them on from the director end in order. Mixing orientations will throw the element spacing off.
Mark the element centers on the dowel first, then slide each ring on and line its wire tunnel up with its mark. Lock it with the wood screw.
Feedpoint: strip the coax, crimp a ring terminal on the center conductor and one on the braid, then screw each terminal onto its element half and clamp the cap. The wire halves slide in until they stop at the blind end of the tunnel, which sets the 16 mm gap.
Connector: I terminated the coax with a BNC crimp sized for RG-8X. Choose the radio-end connector gender to suit your radio’s jack.
Print notes (my settings, not rules)
Printed on a Bambu A1-class printer, 0.2 mm layers.
Element ring: print standing on end.
Feedpoint base: flat side down, pocket up, with supports only inside the bore.
Feedpoint cap: print with the parting face down.
Tip spacer: print lying down with the inspection windows facing up.
I’d use PETG or ASA, not PLA, for anything left outside.
Notes
The 16 mm feed gap is my choice, because the original diagram doesn’t dimension it. I held the overall 700 mm span instead, so each half is 342 mm.
These parts were designed in code (CadQuery) with Claude’s help, so the bore size and other dimensions are parameters. If you need a different boom size, ask and I’ll share the script.
Credits: Antenna design by George Smart, M1GEO/G8OCV. Mounting parts by Mike, K1MRE.
If you’d like to attach the script, I can package the CadQuery source with a short readme, one folder with the parts files and the bore size at the top.
