1 / 4
Lap & Desk Sanding Downdraft Box – 3× 120 mm Fans, Fully Printed, Support-Free — zdjęcie 1
1 / 4

Lap & Desk Sanding Downdraft Box – 3× 120 mm Fans, Fully Printed, Support-Free

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Fully printed sanding downdraft box for lap or desk. 3× Arctic P12, magnetic filter cassettes, rear exhaust, no supports

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
22
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution

I've used this several times with great success so far. It's comfortable to place on my lap and is much easier and cleaner than sanding onto my apron and them hoovering it up

It was an iterative design hence why there's retrofit parts. I've yet to put the fence on as I've not seen much dust going down the small gap I have at the back as I designed with some tolerances but then glued the retrofit magnets

It was my first big project using Claude Opus 5.5 and blender mcp

A downdraft box for sanding small parts, such as prints, miniatures and models. It works sitting flat on a desk or resting across your lap. Three Arctic P12 fans pull dust down through lift-out grille cassettes with a filter inside. The air leaves through the back, and the floor is closed, so nothing blows onto your legs.

Features

  • Desk or lap. Three rails underneath make two thigh channels (about 166 mm wide). On a desk it sits flat on the rails.

  • Fully printed, no supports. It comes in three 127 mm modules that bolt together. Each module prints standing on its front face, so it fits printers with a small bed but plenty of height (it fits a 165 mm circle, 230 mm tall). Holes are teardrops and overhangs are 45° chamfers.

  • Magnetic filter cassettes. The work surface is 6 lift-out grille tiles, held down by magnets. Each holds 2–3 layers of cheap cooker-hood grease fleece, kept in place by a push-in retainer grid. To clean, hoover it in place, or lift a cassette out and replace the top layer.

  • Choice of grille: 5 mm holes (52% open), 8 mm (56%) or 10 mm (65%, the fastest to print and stronger).

  • Shaped airflow. Each fan blows down onto a curved guide that turns the air toward the back, through an exhaust chamber that gets deeper toward the back and out through louvres in the rear caps.

  • No soldering. Every cable hole is 13 mm, big enough for a fan plug. Power is a 12 V barrel adapter, either through a fan hub with a speed knob that sticks on the side (a cable shroud covers the exit) or through a DC-to-fan cable and a 3-way splitter for full speed.

Size: 381 × 232 × 101 mm, plus about 18 mm on the right for the shroud and hub.

Print list

  • Left, middle and right modules (1 each). Print standing on the front face, as exported.

  • Rear cap ×3

  • Grille cassette ×6 (pick the 5, 8 or 10 mm version)

  • Filter retainer ×6

  • Retrofit parts (magnet blocks/pads, cable shroud). You only need these if you printed an early version without magnets or the shroud. Skip them otherwise.

Walls are 1.6 mm, so use at least 4 perimeters. 0.2 mm layers give the cleanest 45° faces; 0.32 mm works if you want it faster. I printed mine in PLA. A full set is about 1 kg.

Hardware

  • 3× Arctic P12 120 mm fans (plain 3-pin is fine)

  • 12 V DC adapter, 5.5 × 2.1 mm plug, ≥1 A

  • Either a fan hub with a speed knob and a 5.5 × 2.1 DC socket (I used one about 44.5 × 44.5 mm; it slows 3-pin fans too), or a DC-socket-to-fan cable plus a 3-way fan splitter

  • 24× 5 × 2.5 mm disc magnets

  • Cooker-hood grease fleece (or G3/G4 filter media), cut to 120 × 110 mm

  • 24× M3 heat-set inserts

  • 12× M3×30 (fans), 12× M3×6–8 (rear caps), 8× M3×8–10 + nyloc nuts (module joints)

  • Gel superglue or epoxy for the magnets, 6 stick-on rubber feet, a bit of foam or Blu Tack to plug the fan-lead holes

Assembly in short: inserts in → magnets glued in (all module magnets one pole up, all cassette magnets the other pole down, so any cassette fits any slot either way round) → fans screwed on from above, blowing down → modules bolted together → leads routed through the wall holes and floor clips to the right side → rear caps on → filters and retainers in the cassettes.

Limits: P12s have low static pressure, so keep the filter coarse (G3/G4). A HEPA or F7 pad will choke the airflow. It catches the visible dust but not all of the ultra-fine particles, so still wear a mask for long sessions.

Tagi