1 / 6
Porsche 924 & 944 (Steel arms) Front Sway Bar Outer Bushing — zdjęcie 1
1 / 6

Porsche 924 & 944 (Steel arms) Front Sway Bar Outer Bushing

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Greasable design. Replace the rubber bushing with a solid TPU part, or use this as a positive for casting polyurethane.

Ocena
5 / 5
Polubienia
16
Pobrania
129
Wydruki
1
Wyświetlenia
1016
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial

Uploading this to address 2 issues with the status quo, affecting any 924 or 944 with the steel front control arm design. Note that this is discussing the outer bushing, at the control arm.

  1. Stock rubber bushing will only work with the smaller sway bar diameters. The ends (that go into these bushings) are thicker on 25.5mm sway bars and higher. Therefore if you wish to upgrade to a larger front sway bar, the main option is to drill out the rubber by a few millimeters.
  2. To my knowledge, the only aftermarket direct replacement option is offered by PowerFlex, part number PFF57-307. However there have been fitment issues reported as recently as 2019, some chamfering may be needed. The PFF57-207 version is sized incorrectly and is to be avoided. Unfortunately for both of these parts, the inner bore is sized for the smaller sizes of sway bars and again requires drilling, per the above.

Note that Lindsey Racing sells a mount which replaces the factory design altogether, part number LRA-ESBM, and enables you to use the 85.5+ bushing design. At the time of writing this kit costs 160 USD.

 

This design attempts to solve for these shortcomings:

  • Sized for larger sway bar ends: ~19mm bore
    • I am attaching the SolidWorks file if you wish to reduce the bore diameter to fit the smaller sizes. I do not have this measurement on hand, it is very slightly smaller.
  • Greasable design - there is a provision for a zerk, and internal grease channels. If you do not wish to drill and tap the drop links, this shouldn't be a problem to leave as-is.
  • Slit in the base to facilitate installation. It is tight, but will go in.

 

For those wondering about the durability of a 3D printed bushing, this is admittedly not well studied. TPU printed at 100% infill is incredibly robust and virtually isotropic… cutting one open reveals no evidence of layer lines or an obvious ‘strong’ or ‘weak’ load axis bias. I am running these on one of my cars and will report back if I ever have issues. These are (generally) not a safety-critical item so I am more comfortable experimenting with these compared to a control arm bushing.

 

Printing:

  • TPU: I chose 95A Shore hardness and this seems like a reasonable compliance. Going stiffer may lead to a more frustrating installation.
  • No supports or anything like that.
  • 0.2mm layer height, 0.5mm extrusion width (I am using a 0.4mm nozzle)
  • 100% infill. The ‘concentric’ infill pattern gave me the best results.
  • Print with the center bore aligned vertically.

 

Installation:

  • Recommend removing the drop links from the car for this
  • Soak parts in very warm water to temporarily lower their stiffness
  • If a grease zerk is used, mark the drop link for drilling using the print as the reference. Suggest drilling and tapping prior to installation of bushing due to metal debris.
  • Deform the bushing into a corkscrew shape, due to the slit at the base.
  • Insert one end of the deformed bushing, and get the ‘lip’ engaged around the other side of the drop link. This may take some time and prying.
  • Apply light lubrication to the faces that are still visible, and push the rest of the bushing into place.
    • A vice would be very helpful here. However I found that a large pair of vice grips also worked for this step.
  • Grease bore as usual with whatever you planned to use.

Please note the Creative Commons Non-commercial license. I am uploading this for the community for free, please respect that by not trying to capitalize on my work by manufacturing and selling these.

Tagi