P
Printables
OneUp V3 Dropper Post Upper Bushing
OneUp V3 Dropper Upper Bushing replacement part. Printed with PETG, brim and 0.15 layer height.
Wyniki wyszukiwania: bushing
Liczymy pasujące modele…
P
Printables
Creality dryer box bushing
This bushing prevents the bowdentube from being pulled into the dryer box when filament is being pulled by the extruder. Printed in TPU.
P
Printables
Acura Integra B-series shift linkage bushing (transmission side)
This is a model of the shift linkage bushing on the transmission side of a B Series Acura Integra. This should be very accurate but the only part I wasn't 100% sure on was the taper for the dished side of the bushing as I didn't have the…
P
Printables
Parkside welder spool bushing for PIFDS 120 B2
Parkside welder spool bushing for PIFDS 120 B2
P
Printables
Printable Bearings (Bushings)
About the model: A simple 608 size bearing replacement for when you can't be bothered to order the real thing for your simple little 3D print and would rather just print the bearings too (we've all been there right?). They spin very…
P
Printables
Browning 1911-380 Barrel Bushing Wrench
This is a wrench to remove the Barrel Bushing on a Browning 1911-380 (It may also fit the Browning 1911-22 but I have not confirmed if it fits) I printed it in ABS at 100% solid for extra strength.
P
Printables
M5 14MM Bushing 9MM Tall
M5 Bushing – 3D Printable (9mm Tall) Inner Diameter: 5.2mm (Fits M5) Outer Diameter: 10mm (5mm high) Flange Diameter: 14mm (4mm high) Total Height: 9mm 🔧 Print in a material suited to your use case , such as PETG or ABS for durability ,…
P
Printables
Coax Feed-through Bushing
Ever need to drill a hole through your wall for coax? The installers use a feed through bushing on the outside of the house for a snug fit, keeping bugs and weather out. I tried 2 versions. The first had the guide, then a rubbery TPL…
P
Printables
AW11 Clutch Pedal Clevis Bushing
Remove the slop from your clutch pedal clevis with this bushing. I recommend printing with TPU or ABS for the best fit
P
Printables
Locknuts, Blanking Plugs, Bushing and Washers
A collection of blanking plugs, bushing, locknuts and washers. Blanking Plugs: for blocking off holes in metal trunking, panels or equipment racks. Plain circular with screwdriver slots (BPP) or hexagonal (BPH). Bushing: for routing a…
P
Printables
Tractor cat2 to cat1 bushing and pin holder
this model holds bushing for tractor cat1 attachments if you have cat2 tractor, and it has two holes for holding pins wh
P
Printables
Fender / Squier Mustang Hardtail Tremolo Bridge Bushings
I made these bushings to lock the stock bridge of my Squier Mustang Classic Vibe when I hardtailed the Tremolo. I've seen people use electrical tape and that didn't seem as sturdy so I made these bushings. They are slightly tapered since…
P
Printables
Additional holders bushing
I made a small bushing so the additional holders will fit in the HSW. The original design is a bit to small to fit. This way, the additional holdes will fit. Just print on your normal settings. This will take about 4 minutes. Print with…
P
Printables
Shifter Cable Bushings for the Veloster N, i30N, Elantra N and Avante N (MT ONLY cars)
Tighten up your shifter even more than what you can get from just the shifter base bushings alone. Not many have dabbed into shifter cable bushings for this car. For other manual cars, many performance shops do this as soon as the new car…
P
Printables
Support pin for filament spool holder with guide bushing
This support pin makes use of the guide bushing, screw, and nut from the filament holder that comes with Prusa Mk4s printers (and perhaps earlier ones) to guide the filament coming off the spool. Depending on how it's orientated, without…
P
Printables
Boot/bushing tightening tool for Neutrik XX
A simple tool to tighten up the boot / bushing of Neutrik XX series connectors.A simple tool to tighten up the boot / bushing of Neutrik XX series connectors.
P
Printables
3/4" x 3/8" bushing sprinkler blowout adapter
Adapt from 3/4" FPT down to 3/8" MPT. This is just a standard pipe bushing. I used this for blowing out sprinklers this fall. Careful if you thread this into PVC tightly you are probably not getting it out unless you used teflon tape. I…
P
Printables
Office Chair Castor Bushing
I put NAIERDI Office Chair Castor from aliexpress ( https://www.aliexpress.com/item/32944808613.html ) to my IKEA Markus chair and was very happy with them. However, after a year some debris (cat fur mostly) build up in top open axial…
P
Printables
Ford Focus Gearstick Bushing
I make no promises or guarantees, use at own risk and try not to break any of the plastic pieces of the assembly or center console while removing or reinstalling. Made to fit my 2002 ZX5 Ford Focus, will also fit my 2010 ZX2 Ford Focus.…
P
Printables
Flashforge AD5M Pro LED bar on AD5M with 3rd gen minimal enclosure bushings
Thanks to Doug Joseph I put together a custom enclosure kit for my FlashForge AD5M. You can get the This LED bar real cheap, but it has weirdly big holes in it. Remove one of the connectors (doesn't matter which) from the LED bar and run…
P
Printables
MK1/2/2.5 Miata/Mx5 suspension bushing mould
Wanted Polybush my mk1, but bush kit is extremley expensive, so went down the route of printing moulds and casting myself. Designed based of existing polybushes(borrowed of my friend and took dimensions). Printed in TPU95A, I would advise…
P
Printables
Volvo engine mount bushing
3D‑Printed Upper Engine Mount Bushing for Volvo 5‑Cylinder (OEM 1029703) Replacement bushing for the upper engine mount on Volvo 5‑cylinder models using the OEM part number 1029703. This design replaces the original rubber bushing with a…
P
Printables
Mazda NC MX-5 Miata Clutch Spring Bushing
I used this on an 2015 NC3 but I believe it will work with any NC. You'll need to print two pieces, one for each side. A previous design fell apart after a few days, so I'm hoping this design holds up better. We'll see. Update: 2 months…
P
Printables
Traxxas E‑Maxx Differential Bushing
A precision‑fit bushing set designed for the Traxxas E‑Maxx differential assembly. This pair of spacers tightens tolerances, improves alignment, and supports both stock rebuilds and custom driveline setups—including 6×6 conversions and…
P
Printables
Cable Bushing
Secure USB-C cable pass-through bushing designed for an automotive console wall. Features a two piece interlocking design and requires no supports for printing. Printed using TPU (inner) and ASA (outer) filaments with 0.4 nozzle and 0.2mm…
P
Printables
Ford IB5 Gear Shifter Bushing | Focus, Fiesta, Fusion, C-Max
Replacement bushing for the IB5 manual transmission, used in various Ford models such as: Focus, Fiesta, Fusion, C-Max, etc. Designed as a direct replacement for the gear shift selector bushing, which commonly breaks over time and causes…
P
Printables
Scion Tc Top Radiator Bushing
Created these to replace the rubber bushings in my top ratiator brackets to stop the movement of my radiator. I recommend using high temp resistant material.
P
Printables
Labeled Wombat Ordnance Annealer Case Bushings
Simple remix of the already execellent bushings provided by Wombat Ordanance on Thingiverse. I just added some simple labels: 223, 308, Mag, Lap to make identifying which is which quicker.
P
Printables
Handboard / Fingerboard bushing
This model will allow you to print some handboard or fingerboard bushings (for fingerboard, you'll need to scale it down) Tried it on some China Handboard trucks & 2004 Tech Deck handboard trucks and worked like a charm. For handboards,…
P
Printables
Bmw e30 front lower control arm bushing
This is for all you E30 fans out there that need the lower front bushing. I used TPU 95A.
P
Printables
HÅG HAAG H05 Creed Office Chair Dampener Sleeve Bushing
I made this dampener/bushing/sleeve for my HÅG H05, as the original one was worn and, and it started to make a lot of noise because of the metal on metal. This also means, that the rod that holds the chair in place, was starting to wear,…
P
Printables
Audio Strider 990 Bushing
I recommend printing this model vertically with 85% infill to maximize strength. Otherwise good luck and I hope you can get your elliptical working again. print settings for my ender 3 v3 85% infill no supports petg brim 3 walls note that…
P
Printables
BMW E46 gear shifter rear bushing
You must use the old metal housing. Printed in FLEX and glued inside. OEM: 25111222015 Strongflex: 031933 Should fit: BMW 1 E81 E82 E87 E88 BMW 1 F20 F21 BMW 2 F22 F23 BMW 2 M2 F87 BMW 3 E36 BMW 3 E46 BMW 3 E90 E91 E92 E93 BMW 3 F30 F31…
P
Printables
03 to 07 Honda Accord V6 Radiator bushings
2003 to 2007 Honda Accord V6 Radiator bushings. Printed in TPU
P
Printables
2008 - 2021 WRX and STi Transmission Crossmember Bushings
Important Legal Disclaimer for Digital STL File Product: 3D Printable STL File – Transmission Crossmember Bushing Vehicle Fit: Subaru WRX (model-specific design) About This Product This listing provides a digital 3D model (STL file) only…
P
Printables
GS500 bar end bushing - original
17mm diameter 20mm total length (15 + 5 for the nut to sink in) Replacement for your 20yo rubber bushings that fall apart inside your GS500 (or any other 17mm inner diameter) handlebars. Printed in TPU 95A, they fit great. If you want to…
P
Printables
Bushing for Generic 51/53/54/57/58mm Constant Pressure Coffee Tamper
3d printable bushing for generic coffee tamper. Longer contact surface and better tolerance helps with keeping tamping part parallel and consistent. Its Generic Chinese thing, your may have different shaft or whatever, you may need to…
P
Printables
Patio Table Umbrella Bushing
No matter which patio table you buy, the umbrella bushing always seems to give up after a week. That ends now. Meet the perfect replacement — a precision‑printed TPU bushing that installs in seconds, stays quiet, shrugs off the elements,…
P
Printables
Ukulele Repair Parts (Tuner Bushings + Bridge Saddle, Snap-Fit, Tested)
I designed and 3D printed replacement parts for my first ukulele: - tuner bushings (snap-fit) - bridge saddle (custom shaped) One of the original bushing was missing, and the saddle was damaged, so I recreated both parts using Fusion 360.…
P
Printables
Liberta stroller - bushing
Replica bushing for attaching the leather strap for a 1986 Liberta stroller.
P
Printables
Rack & Pinion/Steering Rack Bushing For Honda CR-V RD1 (Gen1) 1997-2001
Applicable Models: Honda CR-V 1997-2001 RD1/Gen1 PRINT NOTES: Material: TPU 95A (I recommend NOT softer than 85a) Walls: 99 (Far more rigid compared to 100% infill, but as you like) 1x "Steering Cut Bush" 2x "Steering Bush" (Naming is a…
P
Printables
2008 Ford Mustang 4.0L V6 Lower Radiator Bushing Mount
While replacing the leaking radiator in my neighbors Mustang I inadvertently dropped the lower radiator bushing in my coolant catch bucket without realizing it. When I went to reinstall the radiator and couldn't find it I didn't freak…
P
Printables
IKEA TJUSIG Replacement Plastic Insert / Wall Mount Bushing
This is a replacement plastic insert for the IKEA TJUSIG hanger. The original plastic part can break or wear out over time, causing the hanger to become loose or unstable. This model is designed to be strong, easy to print, and compatible…
P
Printables
1911 Tabletop Bushing Tool
This fixture makes removing the bushing from a 1911 easier and safer by adding a fence that prevents unexpected movement of the recoil spring and plug. After you unload the weapon, remove the magazine and engage the safety. Then press the…
P
Printables
4 in to 2.5 in bushing
Adapter to fit a 4 inch vent cover to a 2.5 in internal air vent fitting. For whatever reason, the bathroom fan exhausts on my home are 2.5 inches diameter; but the smallest easily available commercial exterior fitting is for a 4 inch…
P
Printables
Tuleja ślizgowa napędu bramy Nice / Gate Pivot Bushing
[PL] Zgubiłeś lub zniszczyłeś plastikową podkładkę między trzpieniem a uchwytem ramienia napędu bramy Nice? Ten mały element to tuleja ślizgowa, która zapobiega tarciu metalu o metal i zapewnia płynny ruch obrotowy podczas otwierania…
P
Printables
Rage rover windshield lateral trim clips and bushing
The pin can be made out of petg or abs, but the bushing needs to be made out of tpu
P
Printables
USS Drybox bushing for Fiberon spools
Bushing to make Fiberon spools fit and spin free in the USS drybox. I printed it in PETG but any material will do. The dimensions are inside 52mm outside 54,8mm length 70mm. A freecad file is included to modify if you want. Check here for…
P
Printables
Damper bushing Passat b3 VAG 052 129 669 A
Демпфер-втулка корпуса воздушника, тестил на Пассате б3 g60 syncro, по каталогу идет на приличное количество машин VAG семейства Damper bushing for the air filter housing, tested on a Passat B3 G60 Syncro, also fits a large number of VAG…
P
Printables
Rlaarlo Stormbreaker Wing Bushings and Mount
My wing kept breaking off every time my Stormbreaker would hit it when it flipped. I made this as a replacement since if you add rigid bushings it tears out the thread area of the wing mount. The center bushings are intended to be TPU for…
P
Printables
Sachs/SRAM S7 Fixierbuchse/plastic bushing
Plastic bushing for Sachs/SRAM S7 bicycle hub gear shifter. This is that red plastic part that sits on the shaft, between it and the shifter. It holds the shift tube in the correct orientation for the teeth inside the shifter to engage…
P
Printables
Subaru sambar Shifter bushings
Subaru sambar Shifter bushings to my KS3 sambar 1995 May or may not fit KS4
P
Printables
NB Miata Horn Button Bushing/Insulator
These disintegrated when I went to install a Cipher steering wheel, so I made some replacements. I printed the bushing in PETG and the Insulator in TPU.
P
Printables
Rancho Shock Absorber Bushings
Expanding on the Rancho Shock Absorber bushing files I made earlier. This set includes the L1 and L3 hourglass bushing shapes as well as the LS straight bushing. Files are OpenSCAD and they allow for user specified height/width, inner…
P
Printables
Miata Auto Transmission Bushings NA/NB
Your automatic transmission shifter feeling sloppy? Don't want to spend $50 on replacing them? Welp, here you go. You will need two of each bushing for the job. Recommend Nylon, but I printed with ASA for a 2003 Miata. Should fit all…
P
Printables
Rocky Mountain Bike Bushing
Rocky Mountain Bike Bushing For Rocky Mountain Flatline rear suspension. M8 Threads. ASA .2 Layer height 100% infill Supports if you want If you like, like. Ride on and enjoy.
P
Printables
Miata door bushing
Decided to make my own door bushing since I was never fully satisfied with the one I downloaded. They were either too loose or too tight. I made mine simple with virtually no play with the correct radius so they fit properly in the cup.…
P
Printables
Qidi X-Plus 3 and X-Max 3 Anti-Vibration Feet Bushings for M4 button head screws
Remix of the anti-vibration feet bushings by SomeDude with the holes for the screw head widened a bit to use M4x25 button head screws.
P
Printables
BMW Tensioner Bushing 11281748718
Tensioner Bushing OEM SKU 11281748718, spare not sold any more. Beware of shrinking and/or warping while printing this. I had it printed in PLA with those exact dimension because I found out that my P1S was printing it 0,1mm smaller in…
P
Printables
Bushing and Nut for Changegears
Addtional Nut and Bushing for Emco Maximat Super 11 Lathe. The bushing is part of the stud to mount changegears. The M18x1.5 finethread needs to be recut - you can do this with the threads of the original stud in your lathe (ASA has more…
P
Printables
Bally T bushing shooter lane guide
This Bally shooter lane guide bushing uses a Williams shooter "coil" sleeve. I made this thinking the original part was no longer available...but it is...but if you want to do something on your own, here it is. I printed this with the…
P
Printables
Espresso Leveling Tamper Bushing
Bushing that free up slop in this self leveling tamper: https://www.aliexpress.us/item/3256806897868416.html?spm=a2g0s.12269583.0.0.40876595OcScEC&gatewayAdapt=glo2usa
P
Printables
Bushing for a Ford Falcon 2004 Automatic
Bushing for a Ford Falcon 2004 Automatic shifting cable, I believe its the same for 2000-2005 but don't quote me. Hopefully this helps someone, saved me a few $$ on a new cable so Enjoy! Print Settings Supports: Yes Resolution: 2.5…
P
Printables
Tacoma Tailgate Bushing
This 3D model is a replication of the OEM tailgate bushing designed for the 2016 Toyota Tacoma, part number #66143-04020. I printed this in PLA for fitment testing purposes but have not tested other materials.
P
Printables
Anet A8 vertical bushing mount
This is a mount for the vertical bushing of the Anet A8. You can fit a light, a camera holder, etc on it; you just need a 6.25 mm hole in it. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: Yes Resolution: 0.1 Infill:…
P
Printables
6mm GT Bushing
Print the same as the other bushings. Settings: .2mm layer height 3 perimeters 40% infill Orientation - Larger end on build plate No supports
P
Printables
OneUp V3 Dropper Post Upper Bushing
OneUp V3 Dropper Upper Bushing replacement part. Printed with PETG, brim and 0.15 layer height.
P
Printables
NV271d tail housing bushing tool
I made this tool to press the old bushing out of the tail housing and to press it again, i used petg cf and pet g both held up pretty well with my 15 ton hydraulic press
P
Printables
1UP Bike Rack Lock Bushing
These bushings go on both sides of the hitch lock provided with 1UP hitch-mounted bike racks. In my case I am using the Super Duty rack with a 2" hitch which measures a little over 2.5" outside (64.4mm). I printed these out of TPU with 3…
P
Printables
Honda Izy lawnmower - wheel bushings
Honda Izy lawnmower - wheel bush - flanged Size 13mm (ID) x 27mm (OD) x 20mm deep These replacement bushes are an upgrade on the original parts. The bushings on my old Honda lawnmower all failed. I found it difficult to find replacements…
P
Printables
Skate Bushings - Short Barrel
Skateboard Longboard Bushings - Short Barrel Material: TPU (Shore A) Height：15.24mm/0.60in Diameter：24.638mm/0.97in Hole Size: 9.14mm/0.36in Are these safe for using on a skateboard? Probably not. It will depend mostly on the material…
P
Printables
Bodum Chambord French Press lid button/bushing
The button that holds the lid on my french press together (and acts a bushing for the plunger rod) broke. This is a replacement to bring the french press back into action. Printed on its side as oriented in STL, no supports, in PETG for…
P
Printables
Subaru Impreza WRX 2006 2007 gear lever bushing
My WRX was missing one of these, and the other was all worn out. Replacing these fixed my gear lever flop. Not a high temp environment nor a critical safety piece, so safe to print and use. Tolerances are tight with my flashforge finder,…
P
Printables
Printable molds A4 B5 Sedan Rear Hatch Bushing
3d gedruckte Formen zur Herstellung von Kabeldurchführungen für alle A4 B5 Limos. Diese Durchführungen sind ersatzlos entfallen, somit nicht mehr verfügbar. Der Nachbau aus Silikon ist sogar besser als das Original! Der Käufer der Daten…
P
Printables
Router Bushing Organizer
A rack that holds up to 10 router bushings. Printed in PLA in three parts. The dovetail connection needs no glue or fasteners. The rack is held to my bench with 4 wood screws.
P
Printables
36 Nash shock bushings
Impossible to find shock absorber bushings for 1936 nash cars. May fit others. Tested on AACA members car. Print with 100% infill with flex or TPU
P
Printables
Shift lever bushing
A Volkswagen compatible shift lever bushing as requested by a Reddit user.
P
Printables
Chrysler Shifter Bushing
Shifter bushing for various Chrysler models (the small one) Made with what was measured off of the original Chrysler part my father-in-law took out of his PT Cruiser. I made a 2-part version aswell if you fancy a more original looking one.
P
Printables
Napoleon Door Bushing (N105-0011)
A printable replacement bushing for Napoleon part number N105-0011. Mine broke, so I decided to save a couple bucks and print a replacement. I wouldn't recommend PLA for this since the door gets hot enough to soften that material. I used…
P
Printables
Extractor for Fox Racing Shox Lower Leg Bushings
This is an Extractor for Fox Racing Shox Lower Leg Bushings. There is the video that explains how to use it! This version works well with 32mm forks. I don't know if it will work with the stepcast version. Printing it in pla (100% infill)…
P
Printables
Wave Runner FX series Gas Lift Bushing for front hatch
WaveRunner gas lift bushing that should fit the part #F1B-6515D-01 Print at high resolution PETG - face down. no supports needed. You might find the part can break if you try to remove it. Fits wonderfully. But removing will probably…
P
Printables
Shredder Bushing and Peeler (Aurora AS1712X)
This paper "peeler" and hex bushing are replacement parts for the Aurora AS1712X shredder. The "peeler" acts as a spacer between the cutting wheels and helps peel the paper away from the cutter axle/post as the paper is being shredded.…
P
Printables
Shock Mount Bushing Parametric SCAD
Test how well a printed bushing can work. Normally a steel tube strenthens the bolt in a wider mounted shock end, in that case one can probably also adjust this design via parameters to be just the spacer. Print Settings Printer: Ok…
P
Printables
Bosch Colt 1 HP Guide Bushing Sub-base
This is a 6" round sub-base for a Bosch Colt 1 HP PV20EVS router designed to accept the Harbor Freight brass guide bushings. It works with the stock fixed base. It may work on other routers or with other guide bushings, but this is what I…
P
Printables
Router Guide Bushing Storage Box W/ Lid and Measurements (Harbor Freight)
The original design is great. The only change I made was adding raised text with the size of each bushing. I colored the top of the letters with a gold paint marker to make them easier to read. Edit: I made one more update so the lid uses…
P
Printables
Bosch 1617 Guide Bushing Adapter
I have a Bosch 1617 router. I love the router, but I'm not a fan of proprietary accessories like the Bosch guide bushing set. I got a set of bushings from Harbor Freight and modeled this to work with them. The screw holes are not actually…
P
Printables
SSR bushing cover
Made a simple cover for my SSR wheels. External radius is 62.5mm, could work on other wheels. The bushing size for the wheel is 72.2, but what count is the external radius. use the fusion 360 file to edit to your liking. Category:…
P
Printables
Babybay Replacement Roller Bushing / Hülsen für Rollen
The Babybay baby bed can be equipped with rollers to convert it into a bassinette. The rollers are secured by bushings that are pressed into the bottom of the bed. In our case one of the bushings broke (of course during a long weekend)…
P
Printables
Anti-Rattle Bushings for Ender3 V3 KE/SE Y-Axis Linear Rods
The Ender3 V3 KE used to have two screws in the front that would hold down the linear rods in the base housing. Recently, there was a design change and Creality eliminated those screws (they were also too short). Now, on some production…
P
Printables
Glass Patio Table Umbrella Hole Bushing
Two pieces Recommended Print Settings Print Orientation: Default as modeled for the bottom, Top down for the top piece. Material: PLA Layer Height: 0.20 mm or less Infill % : 15% or more Supports: None Raft: Optional Brim: Optional
P
Printables
VW Golf MK 3 Variant (Station Wagen) Rear Axle Bushing press Tool
Press Tool for inserting the bushing of the rear axle of a VW Golf 3 Variant/Station Wagon. Two pieces required, plus: 2 pcs 50mm o.d. Washers for M12, (strong ones, t ~3mm) or a combination of washers to distribute the load/pressure 1…
P
Printables
Makita Plunge Base for Katsu bushings
Replacement plunge base bottom for the Makita palm router, allowing you to use the Katsu bushings / copy rings. I made it the same thickness as the original bottom so it can be used with the standard bolts. I took inspiration from this…
P
Printables
Le Creuset Pepper Grinder bushing
Replacement bushing for a medium sized Le Creuset Pepper Grinder
P
Printables
Nissan Micra trunk plate bushing
This is a bushing for trunk plate of Nissan Micra K12 (2003-2010). No screws needed but your plate may not be damaged too much. Print Settings Printer Brand: Prusa Printer: i3 MK2S **Rafts:** No Supports: No **Resolution:** 200 Infill:…