1 / 5
Modular ITX/DTX/mATX/ATX/SSI-EEB/SSI-CEB/EATX/XL-ATX mainboard frame/tray [Updated 2026-07-19] — zdjęcie 1
1 / 5

Modular ITX/DTX/mATX/ATX/SSI-EEB/SSI-CEB/EATX/XL-ATX mainboard frame/tray [Updated 2026-07-19]

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A simple modular PC mainboard frame/tray system intended for open-air or custom enclosure PC builds.

Ocena
4,556 / 5
Polubienia
430
Pobrania
3797
Wydruki
7
Wyświetlenia
23 535
Oceny
9

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
BSD License

Introduction

This is a simple PC mainboard frame/tray system intended for open-air or custom enclosure PC builds. The intent is to support a broad variety of mainboards from iTX to so-called EATX with modules that fasten together with M4 nuts, bolts, and washers and accommodate standard M3 mainboard standoffs.

PETG-ESD filament is recommended for printing since it manages electrostatic discharge. Most 3D-printed materials including inexpensive rapid PETG are non-conductive and can build-up static charge. I doubt its necessary, but to mitigate static with these lesser filaments, ~28awg wires terminated with spade connectors can be run between a few motherboard standoffs and then grounded to the power supply.

Version log

To-do: Design add-on parts to hold a press-fit I/O shield and PCIe cards. In the meantime, this remix holds the PCI tabs for a dual-slot GPU.

  • v3.11 (2026-07-19)

    • Corrected 0.5mm step/discontinuity cosmetic issue on a portion of itx and other parts (thanks to @nanuk)

    • Added back missing standoff hole to matx-full-extension variants (thanks to @Alterix)

    • Added "narrow" version of mATX-full-extension for certain mATX mainboards with two ram slots that are just a few cm wider than ITX. (thanks to @Alterix for the idea)

  • v3.1 (2026-01-17)

    • M4 fastener holes increased from 4mm to 4.25mm diameter to ease fitment

    • add "I/O shield" text to indicate orientation of mainboard

    • added back single piece matx for larger printers like Core 1, P1S, U1, etc.

    • added 1.85mm "trimmed" versions of "EATX" parts to correct standoff locations for some boards

    • added fastening holes for upcoming I/O shield and PCIe card holder parts

  • v3

    • matx1 piece adds a protrusion for an optional standoff location

    • itx and atx parts add optional standoff locations for SSI mainboards

    • re-uploaded files with “medium” detail level to reduce file size

  • v2

    • added missing standoff hole on atx2

    • all standoff and frame holes same size

    • add 0.25mm filets to all edges

  • v1.3

    • matx updated to be 4 pieces instead of 1 to print on smaller printers

  • v1.2

    • added SSI mounting holes

    • recessed landing pads for frame mounting screws

    • added legible part name inscriptions

  • v1.1

    • initial design concept

 

Required parts per mainboard size/format

mini-ITX/mini-DTX/ITX
  • 1 part (itx.stl)

  • 4 mainboard standoffs

  • optional: 4 screws to secure frame to other components

DTX
  • 2 parts (itx.stl & dtx.stl)

  • 2 nuts/bolts + 4 washers to fasten parts together

  • 4-6 mainboard standoffs

  • optional: 4-6 screws to secure frame to other components

mATX (micro-ATX)
  • 4 parts (itx.stl, dtx.stl, matx1.stl, matx2.stl)

  • 4 nuts/bolts + 8 washers to fasten parts together

  • 5-8 mainboard standoffs

  • optional: 4-6 screws to secure frame to other components

mATX  single piece alternates for larger printers
  • 1 part (matx-full.stl or matx-full-extension.stl or matx-full-extension-narrow.stl)

  • 5-8 mainboard standoffs

  • optional: 4-6 screws to secure frame to other components

ATX
  • 4 parts (itx.stl, dtx.stl, atx1.stl, atx2.stl)

  • 5 nuts/bolts + 10 washers to fasten parts together

  • 6-10 mainboard standoffs

  • optional: 6-8 screws to secure frame to other components

EATX (SSI-CEB/SSI-EEB/XL-ATX)
  • 6 parts (itx.stl, dtx.stl, atx1.stl, atx2.stl, eatx1.stl, eatx2.stl)

  • 7 nuts/bolts + 14 washers to fasten parts together

  • 9-15 mainboard standoffs

  • optional: 8-12 screws to secure frame to other components

Notes

  • M3 mainboard standoffs work best (6-32 work ok too). Holes are 3.25mm tapering to ~2.3mm to grip the standoffs.

  • M4 nuts, bolts, and washers work well to fasten frame parts together (8-32 also work). Similar sized screws will work to fasten the frame to a metal or wood bottom plate as desired. Washers should be used to spread the load against the plastic to avoid over-tightening and cracking.

  • 10mm z-height - combined with ~6mm high mainboard standoffs provide ample mainboard heatsink backplate clearance and PCIe card tab clearance

  • Exterior x/y part measurements:

    • itx: 170.33mm x 171.60mm

    • dtx: 170.33 x 72.24

    • matx1: 171.60 x 45.72

    • matx2: 72.24 x 45.72

    • matx-full: 216.05 x 243.84 (243.84 x 243.84 extended version)

    • atx1: 134.47 x 171.60

    • atx2: 134.47 x 45.72

    • eatx1: 134.47 x 86.36 (134.47 x 84.5 trimmed version)

    • eatx2: 170.33 x 86.36 (170.33 x 84.5 trimmed version)


References for mainboard sizes and standoff locations

Tagi