Liczymy pasujące modele…
A soap bar holder with a lid, should fit all rectangular soap bars. Printed in PLA & PETG @0.25mm layer height with 3 perimeters with 30% gyroid infill. Needs one short US #8 stainless steel screw around 1/2in. Please do not cover or…
A small round soap bar holder for round soap bars. Printed in PETG & PLA @ 0.25mm layer height in with 3 perimeters @ 30% gyroid Infill Mesh file is a little small scale it as needed. 175%-200% seems to fit most small bars. Please do not…
351 guitar pick with embedded 5x1mm magnet and a logo that acts as a grip. Printed in Printbed brand PLA with a 0.4mm nozzle @ 0.10 layer height. If using a magnetic nozzle I suggest applying superglue to where the magnet sits and leting…
A simple textured vase. Print tested with PLA in spiral vase mode in layer heights ranging from 0.10mm-0.30mm with a 2mm thick bottom.
A simple lampshade that is printed in vase mode with an adapter plate it rests on. It should be able to fit most floor lamps some modification or scaling of the model might be needed depending on the lamp. The shade should be printed…
An attempt to make the smallest wallet possible without sacrificing structural integrity. Print tested in PLA at 0.10mm layer height with 3 perimeters @ 30% gyroid infill tolerance between parts is 0.10mm. .STEP provided to show how it…
Tested print settings included in print file. Print was tested in PLA with a LED bulb Not for use with incandescent or fluorescent bulbs. Colors with high translucency such as an undyed plastic recommended for the bottom of the print to…
A simple textured vase. Print tested with PLA in spiral vase mode in layer heights ranging from 0.10mm-0.30mm with a 2mm thick bottom.
A “Slim” wallet designed to be both sturdy and as repairable as possible. Print tested in PLA @ 0.10mm - 0.20mm layer heights. Parts have a tolerance of 0.1mm. .STEP file included so you can see how the parts fit together. You will need…
A sturdy 3D printable wallet designed to hold 8 cards plus a decent amount of cash in the forms of both bills and coins. Print tested in PLA at 0.10mm layer height with 3 perimeters @ 30% gyroid infill. Tolerance between parts is 0.1mm.…
Designed to hold a notepad/book above the mouse while not impeding the use of either. The sides fold inward and are retained by a latch to facilitate portability, there is a ridge along the bottom to retain your notebook and a pen. The…
A simple printed part that lets you use an empty filament spool as a support for a shelf you can mount to your desk to serve as a standing desk. The supports can be screwed onto the desk and shelf board as needed. All settings used…
A simple textured vase. Print tested with PLA in spiral vase mode in layer heights ranging from 0.10mm-0.30mm with a 2mm thick bottom.
A simple textured vase. Print tested with PLA in spiral vase mode in layer heights ranging from 0.10mm-0.30mm with a 2mm thick bottom.
A set of printed parts for connecting a 10in ring light i purchased from ebay to the bottom of my DSLR camera witch then connects to the quick disconnect of the Velbon S-6000 tripod i had keeping the light mostly infront of the camera…
Since in this version only the stand is back-compatible it has been uploaded as a remix. An M4 screw 10mm in length is used to secure the handle to the base of the holder, with a thin washer between the screw and the handle, and an…
An upgraded version of the original pet step. It require significantly more non printed hardware to work, but the design allows for both the upper and lower step to fold. this design has been print tested in PLA using the settings…
To wszystkie aktualnie dostępne wyniki.
