P
Printablesntruchsess
BMW i3 washer fluid funnel
Can be printed ‘as is’ (large side facing upwards) with no supports, brim enabled. Diameter (smaller end) is 48mm.
- Pobrania
- 141
- Polubienia
- 21
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
Printablesntruchsess
BMW i4 washer fluid funnel
Can be printed ‘as is’ (large side facing upwards) with no supports, brim enabled. Diameter (smaller end) is 40mm.
- Pobrania
- 112
- Polubienia
- 9
- Ocena
- 0
P
Printablesntruchsess
motorized butterfly air valve/flap
The valve fits standard DN 110 tubes. (They have a diameter of 110m on the outside and aprox. 103-105mm on the inside). The 28 BYJ-58 stepper motor is a cheap geared stepper motor that can easily be controlled by a arduino or raspberry.…
- Pobrania
- 86
- Polubienia
- 22
- Ocena
- 0
P
Printablesntruchsess
BMW i3 center console organizer
I recommend to print 'Body' in PETG - in the car PLA might deform during summer heat. Print-settings for ‘Body’ are not critical - I even used 0.6mm HF nozzle with 0.32mm layers and variable layer hight in Prusaslicer and the outcome was…
- Pobrania
- 83
- Polubienia
- 11
- Ocena
- 0
P
Printablesntruchsess
Oral-B iO Charger Stand
the design allows any fluids that enter the stand from above to leave it through the incorporated channels at the bottom. prints without supports.
- Pobrania
- 52
- Polubienia
- 2
- Ocena
- 0
P
Printablesntruchsess
Oral-B iO travel sleeve
I recommend to print with the large opening facing down. The bridging in the top usually should print without support. As the edge has a bit of chamfer I recommend to enable 'Inner brim only’ to ensure good adhesion to the print surface.
- Pobrania
- 51
- Polubienia
- 6
- Ocena
- 5
P
Printablesntruchsess
Zefal Spin Mirror Aero housing/holder
You need to disassemble the original enclosure and extract the mirror which is glued into the original housing using some double-sides foam tape.
- Pobrania
- 37
- Polubienia
- 2
- Ocena
- 0
P
Printablesntruchsess
MK4S xLCD Vers. A backcover for prusa enclosure with integrated LED diffusor
When trying to mount the original injection-molded housing of the MK4S xLCD to the original prusa enclosure there are several issues: the holes for the screws do not align the position is to high, the xLCD would block the doors. the…
- Pobrania
- 30
- Polubienia
- 5
- Ocena
- 0
P
Printablesntruchsess
enforced crank shaft for 'easy hand crank for Pastamatic'
The crank-shaft that comes with the Easy hand crank for Pastamatic by @thoperSought broke after a few minutes of use. It is originally attached to the lever by a nipple that is held in place by a small clip. I remixed the shaft to use a…
- Pobrania
- 27
- Polubienia
- 4
- Ocena
- 0
P
Printablesntruchsess
BMW i3 Trunk Hatch Stop / Adjustment
the early (pre-LCI) version of the bmw i3 had adjustment-elements on both sides of the back-door (hatch). Those elements allow to eliminate any play that might be there when the lock is engaged. Later (LCI) versions come without those…
- Pobrania
- 23
- Polubienia
- 2
- Ocena
- 5
P
Printablesntruchsess
square-section-key for maintenance-flap
4-Kantschlüssel für Wartungsklappe (Side-length is 7,4mm)
- Pobrania
- 16
- Polubienia
- 1
- Ocena
- 0
P
Printablesntruchsess
Fakro ZRH1/ZRH12 wall mount
Wall mount for Fakro remote control ZRH1 or ZRH12
- Pobrania
- 15
- Polubienia
- 1
- Ocena
- 0
P
Printablesntruchsess
Braun 6522 Shaver Travel Sleeve
A protective sleeve specifically designed for the Braun 6522 electric shaver.
- Pobrania
- 4
- Polubienia
- 0
- Ocena
- 0
P
Printablesntruchsess
Vortex BWO 155 Hakenschlüssel / Hook wrench
Hook wrench to mount/dismount the motor-unit of a Vortex BWO 155 circulation pump
- Pobrania
- 4
- Polubienia
- 2
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.