Liczymy pasujące modele…
I wanted to make my own version that is freely available for anyone to use and customize for their Miku cosplay The main size of these is 80x80mm OD, ~70x70mm ID and 18mm thick. If a different size is desired, scale everything to maintain…
Took measurements of a 50A connector and basically remade it with divets instead of pins and a small ramp on the inside to make disconnection a bit easier on the plastic. It fits quite tight in there, about as tight as another connector…
DO NOT REPOST ANY PART OF THIS MODEL WITHOUT PROPER ATTRIBUTION! FOLLOW THE CREATIVE COMMONS ATTRIBUTION NON-COMMERCIAL SHARE-ALIKE LICENSE TERMS! USE THE REMIX BUTTON! This was more of an experiment to see if I could create such a thing,…
Needed to reset the combination on a master 178 after decoding it and I didn't have the tool. I took measurements of the keyhole and did some guessing based on photos I found online and made this small key that works just like the…
While watching Deviant Ollam's tubular lock decoding video , I saw the RedTeamTools decoder print and its original model by @videograndpa_198951 and I decided to combine the two since they are the same measurements, offset by one. Note:…
I couldn't find a good model of a cover for Amass XT-60 female (XT60E-F) panel mount connectors. This is a pretty close remake of the mass produced version I've seen from China before. Printed at 0.10mm layer height for detail. Do note,…
A small edit to the main LCD holder to support the IEC power socket and switch that comes on the Ender 3 V2
Remix of jakabo27's improved panel mount on Thingiverse I recommend NOT printing this in PLA due to PLA's tendency to creep under pressure. Use PETG or similar.
Fitment might vary a bit based on how you assembled yours, but mine fits decently well. Print in PETG for heat resistance. Not too sure how it will react at 20W of heat sustained, YMMV… 30mm screws do peek out of the bottom by 4mm so cut…
I made the bottom holes closed by adding a 3mm thick bottom to them so they wont fall out when you move the holder or whatever it is attached to. I mounted mine on the back of my iron stand so without this they would fall when I picked up…
I modded the original design to taper towards the top to better fit a Chinese stealth bomber frame profile. This is mounted on the underside near the forks. Using a SVMC72150 controller. I also increased the height of the base piece by…
The belt clip release latch on the Motorola Minitor 5/V pager is known to break really easily. I decided to model the part that breaks, so as long as you have the belt clip, spring, and rod, you can repair it without needing to buy a…
A small dual-color print keychain of the prominent cross and dot symbol found in the anime and manga Girls' Last Tour. Printed at 0.2mm layer height on Prusa MK4 in PLA. M600 color swap at 3.2mm height Made in Fusion360.
Modded the lefthand piece of the model to accept this USB charger module. https://www.amazon.com/gp/product/B09W48M3SG You can print this and the original stem for a bike light, or this and the included modified end piece to just have a…
Recreated the black badge seen on the Onewheel Plus/+XR for making custom designs for vesc etc. Import the .step into your preferred modeling software or place the .stl into PrusaSlicer and right click on the model > Add Modifier > Text,…
This enclosure was inspired from the Adafruit version that supported a different MCU, but I specifically needed to use the MatrixPortal S3 for WLED-MoonModules compatibility. I also compensated for using 0.75mm thick LCD diffuser plastic…
Recreation of the main cam assembly and gear for the Time-O-Matic neon sign controller. The original gear is wooden(?) and seems fragile. Mine had broken teeth. .STEP files included for easy modification to suit your needs, including a…
Remix of the original design by ryaninc to allow the piece to be used either with the tab facing up (if the phone is wall mounted) or the tab facing down inside the phone body (If the phone is just standing on a desk). Printed it on my…
Brakelight/Taillight bracket for the (less) cheap chinese ebike light kit with 70mm spacing . Mounting holes meant for 35mm spaced seat bolts on stealth bomber seats. Actual mounting holes are made with 5mm space in either direction for…
I reworked the geometry from my Ninebot max charger mount to fit a 22mm handlebar and mount horizontally. The main hole is sized at 29mm, make sure to check your charger before printing. Print in PETG for resistance to material creep (Do…
The current model of the side cover that sharkset has released is not the most recent one. I physically scanned the ones mine came with on a flatbed scanner, made vector art of it and imported into Fusion360. Extruded that SVG and we have…
Brakelight/Taillight bracket for cheap chinese ebike light kit with 60mm spacing . Mounting holes meant for 35mm spaced seat bolts on stealth bomber seats. Actual mounting holes are made with 5mm space in either direction for adjustment.…
A small frame for a loop antenna made from RG8 coax. Based on this video's dimensions https://www.youtube.com/watch?v=Ivr9VbSgjUU , just with BNC connectors. The frame is to support it since RG8 is quite thin and flimsy. The loop is…
Recently got an IC-R10, it had no belt clip. I have a 3d printer and Fusion360. Now here we are. Threading of the inserts is M3. I used M3x6mm socket head screws and modeled with them in mind. For reference, the space between inserts is…
Close replica of the rear valve part for the model 351.184090 brad nailer. The rear seal leaks partially but doesn't seem to affect much. I can't get the rapid fire setting to work well (never has) but single shot works great with this…
Countersunk the top and bottom for socket head bolts and nuts respectively. An M3x20mm bolt should just about catch the nut and screw in enough to hold it tight. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports:…
I grabbed a set of Motorola XPR3000 series replacement knobs off ebay to replace the stock ones which are pretty meh. I had to trim the slight overhang of rubber off the bottom of both knobs to make them fit nicely. The channel select…
Designed for use with a segmented EFHW amateur radio antenna. The block holds red 22-14awg insulated spade connectors and will not let them separate under lateral tension while strung up. (As long as the terminals connected are smaller…
If you have a Time-O-Matic Model 3 which has a stock or damaged cam, you can convert it into a nicely adjustable flasher suitable for controlling coding mechanisms of sirens such as the 3T22 or Thunderbolt 1003! The cam geometry was made…
Made a mount for this (and similar) buck converters for use in my Ninebot Max G30 scooter. https://www.amazon.com/Voltage-Regulator-Converter-Waterproof-Transformer/dp/B089LRQM9Z I sized the thickness for use with the bolts that come with…
Mark various underground utilities using these 40mm wide markers and a single 3mm nail. They are small enough and low profile enough that they should handle walking and mowing over at your own risk of course. Meant to be printed with a…
Printed at 0.15mm layer height on Prusa MK4 using Overture 95a TPU. Small dab of superglue on the long side to hold it in. Depending on your printer tolerances you can optionally just leave it in without glue and it would stay anyway.
This is a small washer to go beneath the sliding lever and nameplate on Time-O-Matic model 3's to allow the screw to tighten the lever to the coil core and rotate the core without loosening. The original design (which is quite silly)…
Mostly accurate 1/4 scale Lockheed Martin LMS-6 radiosonde model. The holes in the body are most likely too small and I needed to enlarge them with a soldering iron and superglue the pieces in to make them stay. I printed the body at…
PM spacing 74mm, IS spacing 51mm
Replacement bezels for the Cisco 7821 and 7841 IP Phones Magnets are 10mm by approximately 1.15mm
Knurled round cover for the thumbscrews that come with chinese stealth bomber ebike frames. I ended up putting some double sided tape between the screws and caps to ensure they stayed on as I printed mine in PLA.
Brake bleed block designed for DYIsland L4DX-300 or similar brakes. Slide in thru top of caliper. Based off pad and caliper dimensions. Check the second image to see if it will work for you. Print in PETG.
The back cover on the Cisco 7925 IP phone tends to break or crack easily due to their age. This model is a pretty close remake of the original cover. It clicks right in just like the stock cover does and the profile matches pretty close.…
Got a used DP103L from marketplace with a broken depth stop and missing pointer. There's plenty models of the former, but nobody had made the pointer. Well, here ya go. Heated it up with hot air and pushed the rod into it. You might need…
I have a Hoosier treaded tire and even Eric's mud guard didn't fit so I had to mod it. Be advised , you will need to either ditch your footpad/hall sensor connector housings (not the locking ring though) or possibly buy and replace them…
This is a replacement faceplate for HP SCSI SCA hot swap drive tray #5182-4544 and similar. The overengineered latching mechanism snaps easily when forced. This model replaces the entire plate and provides a static finger ring to pull the…
To wszystkie aktualnie dostępne wyniki.
![[.STEP] Onewheel Plus/XR Compatible Rail Badge](https://media.printables.com/media/prints/687161/images/5876797_1538b250-2fd8-476d-a6d7-74df440ea0dc_59a63e60-7427-40ca-bd34-9404b5e4c6a8/newpic.png)
![[Dual Sided] Cisco 79XX Series IP Phone Handset Retention Tab](https://media.printables.com/media/prints/142802/images/1351281_a9050bad-7d25-4e7f-a698-783ea929eaea/large_display_no_tab_142802.jpg)
