Liczymy pasujące modele…
You ever look at one of the containers from a recently-finished Pringles Snack Stack and say that sure looks like a cowbow hat? Me too. Print it flat, use heat to carefully bend the brim to your ideal shape.
Windshield mount for the Aukey DR02 dash camera. I printed the one this is remixed from and it was too loose on my camera. This fits much more snugly. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: .2 Infill: 20-40…
DO NOT PRINT THIS IN ANY SLICER OTHER THAN SUPERSLICER - IF THE INSIDE HOLE DOES NOT SHOW IN THE PRINT PREVIEW, THIS WILL NOT WORK FOR YOU.
I hated how difficult it was to load straight walled cases like 44, 38, and 357 and I kept trying to lose the included collets. So, I designed collets with a beveled mouth that I can re-print whenever I inevitably lose or break one. I…
Harris Tilting Bipod tilt lock lever for the new style large diameter ribbed knob. Hardware: 1x M4x20 button head cap screw 1x M4 nylock Please see my other designs for a lever for the old style small knob.
Needed a drop-down voltage regulator to give me a couple of amps of 12v on my 24v printer to run a 4028 fan. Mount is to add it to the DIN rail on the electronics panel on the back of the printer. It should be a light friction fit. “6mm”…
Complete redesign including new cartridge inserts, a quick detach disc that can be partially rotated to keep cases from coming out when being removed. M4 and spring form an axle to keep the tube holder and disc together while allowing…
The clips on the N20 mask seem to crack and break after a while... yet the rest of the headgear is still in good shape. I harvested the neodymium magnets from the broken clips and epoxied them in. Make sure your glue does not get into the…
I wasn't happy with the available printable cases for the XU4 - so I designed this. I used four M3x25mm cap head hex screws to assemble the case. Update: Download HDMI version if you want access to the HDMI port. Note 1: This is only…
I found that my extruder stepper was running hot (even after tuning the current) on 15-30hr prints and I was getting print failures due to the printed drive gear on the Pitan extruder softening and spinning on the D shaft. I found…
Non-destructively adapt a Forster case trimmer to power. Uses a 1" long 1/4" bit to adapt to your electric drill.
I've been going through and systematically closing all of the open holes on my X-Plus3 because ASA and ABS smell bad (and styrene gases are toxic) and I want all of the air leaving the printer going out the exhaust hose out the window and…
Resin printers stink. FDM printers stink when you print ABS/ASA. My printers live in my office. I don't like headaches from toxic chemicals released into the air by my printers. You know who does like those chemicals? That F*king crow…
Harris Bipod Tilt lock lever for the old style small knob Hardware: 1x M4 x 18mm button head cap screw 1x M4 nylock Please see my other designs for a lever for the new style of knob.
I needed a way to mount a more powerful fan to the exhaust on my 3d printer so I could print ABS and ASA without smelling them and poisoning myself. I went with a variable speed 12032 fan and some inexpensive high quality dust collection…
I wanted an enclosure for a temperature controller that screws closed, has a switch, is easy to install the controller and tighten the braces, has an IEC socket, and provides vents for cooling. Is the design for the cooling vents fun? Is…
Update: Added a Duet3 mini5 mount also. Fits a Duet2Wifi or Duet2Ethernet (since they're the same board). Screw board down directly into the mounting lugs with M3 screws. 3 holes on the side for M5 bolts to bolt to your 20-series…
I found that my Hornady vibratory trickler worked a lot better when tilted slightly and needed to be elevated to work with my scale and not get in the way. This stand tilts it 4deg and lifts it approximately 10mm on the left side. I added…
A clampable block to help you tap straight(-er) holes.
I wanted a better option for de-sleeving primers and pouring them into the flip tray. Small one is sized for CCI sleeves. Larger pour tray is sized for Federal sleeves. Ambidextrous ears for whatever awkward-@$$ way you want to hold it.…
Update: added a 7530 option. Because reasons. I have been getting into Nylon, PC, ASA, and ABS printing and I needed a way to dry my filament. I had been using a modified food dehydrator for years and I noticed that it wasn't really doing…
Do not use this model. See my new version that uses a fan . This one provides too much air resistance to vent effectively. I wanted a right-angle hose adapter for QIDI Tech X-Plus3 BackPanel MOD Kit that I could use with a smaller…
This is a replacement bracket for the bar that secures items on the shelves of the door of my very old Sears Kenmore freezer. Parts for that freezer are essentially unobtainable. Based on my research, I believe this will fit some older…
I had a broken contact pad while replacing the clamp bodies on my Manfrotto 728B. I used Frubino's AWESOME replacement clamp bodies (Thingiverse 37672). I found that the smallest clamp body didn't clamp quite hard enough (I could still…
I have tested this to fit eSun, PolyMaker, and Amazon Basics spools. Minimum ID for the spool must be at least 61mm. Depending on the exact width of the slots for the drive dogs to engage, you may have to "encourage" them to fit in. Gen1…
To wszystkie aktualnie dostępne wyniki.
