Liczymy pasujące modele…
This is a truma roof cap. I printed from ABS, but I think PETG is good to. The first is fits but a little bit it was a little bit loose, bit it can be tighten. (it's in its plase about a month without a any problem) I uploaded the thread…
This is the upper replacement part of a shure microphone holder. Printed with black PETG with support. The stl is a little bit messy, but slicer correct it when u load. top microphone hole diameter: 25mmm bottom microphone hole diameter:…
Customized version of https://www.thingiverse.com/thing:53854 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=53854 Instructions Using the following options: diameter = 10 length = 150 throat_angle = 10…
In my renault megane 2004 is a little bit different, so I modified the part for my own need. There is no upper hole on mine, and the bottom hole is deeper. Thanks for the original design. Category: Automotive
This is a Suzuki DL650 V-Strom blinker housing, that easily brakes when the bike falls :) Very big thanks for "remote" creating the modell to Barbér Máté . Print Settings Printer: prusai i3 rework 1.5 Rafts: No Supports: Yes Resolution:…
https://www.printables.com/model/92532-baby-yoda-elmex-toothpaste-vomit/files
Case for Heltec WiFi LoRa 32 V3 This case is designed for the Heltec WiFi LoRa 32 V3 and includes the following components: Included Components: GPS Module (NEO-6M or GT-U7) On/Off Switch (S3P = SRS3P, 19.4 x 5.6 x 5mm) → Link GY-BME280…
This is for the givi (and similar) engine guards. It protects the guard when you fall with the bike. Print Settings Printer: Prusa I3 rework 1.5 custom Rafts: No Supports: No Resolution: 0.2 Infill: 30% Notes: Printed from ABS, no support…
I lost my suzuki dl650 vstrom spacer under the seat. So I created a replacement one from TPE. Print Settings Printer: Prusa i3 rework 1.5 Rafts: No Supports: No Resolution: 0.2 Infill: 30 Notes: Printed from TPE. Orientation as seen on…
I used this to level the fence with a string and a spirit-level found at home. I just uploaded the long version, couse it is better. The spirit level tube diameter is 9.8mm. 20170526 I modified the hol for the string. Category: Hand Tools
This is a camper window lock replacement. printed from TPU I got the best result with the support when I rotated the thing by 90 degree as seen on the screenshot of slic3r image. You can change szarHossz parameter in openscad file to…
You need M3 screws to hold the gopro mothers at the top. The bottom is fastened with sheet screw.
This is a replacement for the gear shift rubber on dl650 vstrom. It is not used yet just printed, I write here later when i started to use. 2018.04.02. it works (maybe it is a litle bit loose?) Print Settings Printer: prusai i3 rework 1.5…
update 2017-02-22: I created a new stl file for the black GT2, I just narrowed the part where the 2 GT2 touch each other to 2mm. The freecad file is a little bit messy (uploaded too) but I think the stl file is good. I never printed the…
August 10, 2021: I can tell you, it still works after after 2 month of usage. On hard offroad: I used it first 2 days in Hungarian TET, and then 2 weeks in Albanian, Serbian, Montegro TET parts, with really hard rocky terrain. May 28,…
Printed with 0.1mm layer hight from ABS. Use an m3 screw to fasten the endstop on the slider. Be carefull with the screw tightening, couse it can break the gliders stop. Category: Automotive
I'm creating a bigger and more efficient quadcopter (for longer flying time) that can be easily disassembled (to carry). I'd like to be control from the ground station, maybe later with optical recognition by raspberry pi using opencv or…
It is an easy print. I used PETG, 0.32 layer height, 0.32 initial layer.
Just print the top part with 30% infill. It snap fit on the pole. The bottom part is not tested yet with the tent. The goal was to fasten the plastic part to the tent, then when stending up the tent the pole just need to push into that…
This is for the prusa i3 rework 1.5, with 10mm threaded roads frame. You can push it on the front. I printed with 0.3mm, without support. For this housing: http://www.thingiverse.com/thing:213852 Print Settings Printer: prusa i3 rework…
This is not ready yet! DO NOT PRINT IT! It is just for share and test now. Later i'll publish when it is ready.
I scratched 2 lens while I want to remove. So for the 3rd, I designed it to remove and set the focus. It is good for the redmi replacement lens, not for the factory lens. How I Designed This Here is the source file.…
With this Y corner: you can easily remove the M8 roads without disassemble the M10 threaded road frame don't need the zip ties I let the m3 holes tight for the screws that hold the top part. Watch for the gap between the tray and Y corner…
I created a hubsan zino tx gimbal protection, couse what I found can be stored on the tx antenna but I dont want to store there and there is no solution to fasten it to the remote. I designed a hole to be able to add a strap to the gimbal…
DOES NOT WORK STABLE TROUGH GLASS YET, DO NOT USE IT, JUST FOR TESTING. (Maybe it is working with an aluminium surface.) 2016.09.30. With this position I can't setup it correctly :( Feel free to post your idea. At the first place where I…
This is a prop guard for mjx bugs 3 mini/eachine ex2 mini. Its flat not like the original, but its easier to print this form, and I think it works. Print Settings Printer: prusa i3 rework 1.5 reworked by hygy Supports: No Resolution: 0.16…
The durston roads are not enough long for the astagear yun chuan 2 tent. So I made an extender for both sides. Printed with 100% infill, from ABS but PETG is good to. After the print I heated up the modell with a hairdryer, and pushed to…
This is a knob for MZ TS250 for the battery side cover. Added a M6 self locking nut hole. I did not tested it yet. When I printed it i'll modify the descripton.
This is a 3D printable mounting bracket for the dartboard number ring (the metal ring that holds the numbers around the board). Most standard dartboards use several small brackets to support and position the number ring evenly. These…
I wanted to connect the fiamma bipot 30 to a normal drain. Later if it is fitted to the final place, i'll post a photo. Print Settings Printer: prusa i3 rework 1.5 Rafts: No Supports: No Resolution: 0.4 Infill: 30 Notes: I printed with…
GPS holder for iflight green hornet Category: R/C Vehicles
I bought this compressor for my motorcycle, but it travels with the packages. So the other tings can press the power button and discharge the batteries. So I made this. You can fix it with a rubber, or put the whole thing in a textil bag,…
I designed this to stop the jello (vibrations) on iflight green hornet. Its using coated bowdens, I tried with sjcam sj8 pro, but I think the gopro can fit too... It can be fitted to a standrad gopro holder. Check for my other design for…
This is a frame brace for prusa i3 rework 1.5 with 10mm threaded row frame. You need to replace the original back threaded roads to a 30cm long one You need 4 pieces of M4x23mm screw + nut + washer 2 pieces of 36cm long M10 threaded rod +…
I have created a prusa i3 rework 1.5 object and head fan holder, where the side fan angle can be modified easily. You need: 8pc M3 screw 2pc M3 screw nut 3pc 4cm fan Print Settings Printer: prusa i3 rework 1.5 Rafts: No Supports: No…
I printed with ABS but PETG is good too. I just made one, so maybe it is not 100% precise. But I can push the original holder into it.
To wszystkie aktualnie dostępne wyniki.
