Liczymy pasujące modele…
**This design is for HDMI5 V1.2** If you're looking for HDMI5 V1.1 mount, use this one: https://www.printables.com/model/787236-btt-hdmi5-v11-display-mount-voron Notes Mount BTT HDMI5 Version 1.2 on Voron V2.4 and Trident My display came…
DESIGN INTENTS Fun trophy for our annual Superbowl night with friends This is a 50% sized Lombardi trophy. Not an exact replica, some parts were redesigned Designed for 3D Printing = no support needed All details are in the PDF uploaded:…
All details are in the PDF uploaded: Design, BOM, Printing, Some assembly details Files you will find here: Photos PDF “Lack enclosure documentation_Vx.pdf” All STLs Full assembly in STEP ------------------- Our intent was to be able to…
Voron V2.4, Trident, V0.2 and Micron Spool holder Important note Be mindful of the type of bearings you use. You don't want too much free spinning. Try to find cheap bearing (it's not every day we can say that !) or use printed bearings.…
DESIGN INTENTS Replacing thumbsticks that are damaged on PS4 controllers Design for 3D printing (and not a blind replica of the original) Overhangs and bridges have been adjusted to work on any calibrated 3D printer Stick is a little bit…
This design is for HDMI5 V1.1 If you are looking for HDMI5 V1.2 mount, use this one: https://www.printables.com/model/926845-btt-hdmi5-v12-display-mount-voron Design intents There are existing mount for the HDMI5 but I ended up…
Printing instructions STL is oriented correctly No support required Minimum bed size at current scale = 160mm x 160mm (V0 owner will have to scale down) For added rigidity, use 4 perimeters, 40% infill About 1h print (on a Voron), 22g of…
Original design is great. But only 15mm wide for each plier. Mine were larger than that. 60mm x 20mm = refers to the size of the rectangular opening for each plier You will need 2 empty inserts (insert-empty.stl) from the Honeycomb…
Notes Divider similar to the one sold by Yeti Fit the Tundra 45 and 35 model. The divider is exactly the same in both models Print notes STL oriented correctly Size of part on Bed: 275mm x 255mm Very prone to warping due to it's shape.…
DESIGN INTENTS Will hold 32 hex bit (¼") 30 short pockets 2 lateral pockets for longer bits PRINTING PARTS Orientation : STL is already oriented correctly Support : none required Material : Any material will work Infill : 40% cubic Layer…
DESIGN INTENTS Wanted a sturdy accessory box that mounts low on the HSW Open grid pattern in front for aesthetic and access to the M3 screw Bottom grid to prevent the pens and accessories from sliding around PRINTING PARTS Orientation :…
Highlights Hitch cover designed for 3D printing STL oriented correctly No support required Should be printed in Flexible material (TPU, TPE) If you print this STL in rigid material, you will need to scale it appropriately as it won’t fit…
Printable version of a panel clip (clips that hold the panel to the body of the car) for Land Rover Discovery Sport rear hatch. Original clip was made of 2 parts. Plastic clip with rubber ring to prevent rattling. New clip is also made of…
Design intents: Goal was to have diffused lighting for our Voron V2.4 Mount directly to 2020 extrusion Re-use off-the-shelf channel and diffuser (leevalley.com , see BOM) Be able to daisy-chain 3 of them What you'll find here: STLs 3D…
100mm embroidery hoop with compatible display boxes. One hexagonal and one round design. Design intents Nice display for your work once completed Self standing box or wall mount option Two shape to choose: Hexagonal and Round Print notes…
Happened to me more than once where the weighted base of a floor lamp breaks and crumbles in small pieces. Here I replaced it with this new plastic base. The shape of your base may (will most likely) vary from mine. Use the provided STEP…
DESIGN INTENTS This is for the Hoto screwdriver 3.6V (34mm dia x 180mm total length) Hoto can be charged while docked My Hoto came with 25 bits and one extension. The bit holder you see in the photo is this one: HSW-32 bits holder…
Replacement part when your toaster handle has seen too many ups and downs Print notes STL is oriented correctly. Print standing up Material: I use ABS It does not look like the part is seing a lot of heat from the toaster so other…
I re-included the files for 3 sizes of shelf: 3/4, 5/8 and 1/2 (inches)
DESIGN INTENTS Want to store my electronic screwdriver set on the HSW wall Simple to pull out with front and bottom opening Internal size of pocket = 70mm x 25mm STEP provided so you can adjust the size as required PRINTING PART…
DESIGN INTENTS This is a remix of the well done AstroAI holder by jwnicolai I often use my multimeter directly from the holder (my work area is close) so I wanted to be able to keep the probes connected I added a side pocket so I don't…
Herbs pot cover with basil leaves embossing and openings to be able to pickup the inner pot more easily. Print notes Vase mode Recommended width = 1.2mm walls With those settings, it's a 63g - 3h print Size of pot cover (using 1.2mm…
DESIGN INTENTS Replacing missing charging cover on the battery. Existing one can easily be lost Need to fit snug enough to not fall off Designed and sized to be printed in flex material PRINTING PARTS Orientation : STL is already oriented…
Design intent Could not find a single dose hopper with bellows at a decent price on the market for the Baratza Vario plus grinder. They are quite expensive Wanted to keep a silicone bellows (and not a printed one, which won't last long)…
Design goal: Insert that can block the flashing power led while the Sanremo is in sleep mode Can be slid up to see all leds in case you want to use the Sanremo menu system (where the Led lights are used to navigate functions) Design to be…
To wszystkie aktualnie dostępne wyniki.
