Liczymy pasujące modele…
This modified version of my first Aldi/Ferrex battery adapter can be mounted to a surface and uses easily available car connectors (6.35 x 0.8 mm male) as contact blades. I've printed it with 0.25 mm layer height, 0.65mm extrusion, two…
This is a cuboid standing on edge, with a series of shrinking cubes being subtracted on each face. Built in openSCAD. Nothing special, just something I wanted to try … Print Settings Printer: TronXY X5S Rafts: No Supports: No Resolution:…
An enclosure for the DSO138 oscilloscope with room for a 9V battery. Print Settings Printer: TronXY X5S Rafts: No Supports: Yes Resolution: 0.25 Infill: 15% Filament: Generic PLA Any Category: Electronics
This is a rain gauge based on the tipping bucket design. Rainfall is collected in the funnel, then fills up one half of the seesaw until the weight causes it to turn over, emptying the full half and putting the other half under the…
This is a simple protective enclosure for the common 24x WS2812B Neopixel / SmartLED ring boards, mainly to avoid short circuits during prototype setups. White or clear PLA does work best – white for stronger diffusion (direct viewing),…
Just a quick design. This is an enclosure for a cheap bluetooth module, with some space to tuck in the cables. Holes for 3.5 mm stereo jack output and 5.5 mm power supply socket. Extra hole for passthrough of a power supply cable. Update:…
NOTE: NOT FOR THE ORIGINAL RASPBERRY PI CAM ! -- THIS CASE FITS ONLY SMALL FOOTPRINT M12 MOUNT CAMERA MODULE This is a Raspberry Pi camera enclosure with mounting parts for 2020 aluminum profiles with v-slots. You may not need all of the…
Mount the cheap graphical reprapdiscount 12864 "Full Graphic Smart" display with sdcard reader to any 2020 aluminum profile corner with this frame. Needs no support to print. Use "m3direct" version for mounting without brass inserts…
A battery case for 18650 Lipos with room for a perfboard 80x20 mm (e.g. to house both a charge circuit and a step-up converter). Cutout for a 12x19 mm switch to separate the (+) output of the charger/protector from the input of the…
This is just a simple polygonal egg shape suitable for a vase-mode 3d printed lampshade. The refractive effect will very much depend on the printing material, extrusion width and layer height. I had good success with clear PETG and…
I've made it a habit to print a sample vase whenever I buy a new kind of filament – be it color or material. These vase models are designed to fit one into the other with a spiral shape and diameter step up/down of 4mm (except for one…
Tired of zip ties or screws to affix GT2 belts to the print head sled? I know I was, so I made these. One fixed block for the start of the timing belts, and one where you can easily fixate/free the belts by flipping a lever that presses…
This is a rear cover for generic cheap volt meter modules sized 22 x 10 mm, to shield the open electronics from touch or short circuit. The frame module is optional. If used with a cutout of a front plate, the rear cover can be used to…
Parts for a DIY plotter with CoreXY mechanics, based on 2020 aluminum profiles. They're designed to be printed without supports. It's still work-in-progress and does not use V-slot wheels, mainly because I have no source for bargain…
This is a replacement fan duct for the TronXY X5S with a Volcano heater and nozzle mounted to the regular heatsink, and possibly other printers that use the same mounting holes and case. After I modded the volcano block and nozzle on my…
An enclosure for the BigTreeTech SKR v1.3 32-bit 3D printer mainboard. I replaced the stock 8-bit board of my TronXY X5S with this. It can be mounted to the 2020 rails of the bottom frame, like the regular board. Post-Printing…
This replacement cover for the TronXY X5S mainboard accepts a standard 80mm fan with a height of 25 mm. The base and cover both have four pegs that keep both the fan in place as well as the cover once it is clipped on. Main purpose is to…
A modification of the original TronXY motor scheme, using an 8mm steel axle to place the stepper motor at the bottom and transfer the torque to a pinion that's also an easily adjustable belt tensioner. The idea was to be able to easily…
This Z endstop switch mount for the TronXY X5S moves the standard endstop switch to the actual print bed, instead of relying on the proxy of the original adjustable M3 screw. With this arrangement, the bed can be swapped without the need…
UPDATE 2019-Jan-30 -- fixed misplaced counterholes for the wood screws. This is an Arduino-Nano-powered desktop "Do not disturb" sign for those "I’m busy, leave me alone" moments at the office. Press the top front, and it switches between…
This device shows the length of extruded filament for calibrating the extruder steps. The big wheel requires 200 mm of 1.75 mm filament to run along the circumference for a full rotation. The small arrows are 10mm apart each, the long…
To wszystkie aktualnie dostępne wyniki.
