Liczymy pasujące modele…
Holder for a CR2032 coin cell batteries. Battery is securely held in place Single (3V), double (6V) and triple (9V) versions Designed for use with breadboard jumper/dupont wires or bare wire Total holder thickness is 7.3mm for the single…
Open mount to hang a Raspberry Pi 3B+, Pi 4 or Pi 5 from an IKEA Skadis peg board using CSD_Salzburg’s Skadis universal hook . 3 versions available: raspberry_pi_skadis_mount - (Pi 3/4 only) No extra hardware needed, Pi clips into place.…
Different sized gaps (0.2mm – 1.0mm) to suit different thicknesses of paper. One 0.4mm gap clip will just about safely hold a single sheet of 80gsm A4. No supports needed.
Holder for a ‘classic’ (1 ½'' x ½'' / 38mm x 13mm) Zippo lighter on an IKEA Skadis pegboard. Step files available for modification. No supports!
Holder for the common ¼ inch quick connect pressure washer nozzles. Nozzles clip on to the holder and the holder clips firmly on to the ½ inch (approx. 13mm) pipe part of the lance.
Installing a radiator in my case didn't leave enough room to mount a 120mm fan in the correct position, so I designed this bracket to fit a one in the little space left. Two brackets extend a 120mm fan to 140mm and add 4mm in thickness.…
Holder for a single CR2450 coin cell battery. Battery is securely held in place Designed for use with breadboard jumper wires or bare wire Total thickness is 9.1mm Support free print Also check out my CR2032 holder .
This case has been designed to replcae the lid of the GMKTec G3 Plus (Intel N150) to give active airflow to the NVME and RAM. Numerous variations/combos available: 80mm and 60mm fans 25mm and 15mm fan heights Enclosed or flat for mounting…
Extend the height of the GMKtec G3 Plus by around 14mm to a total ground clearance of 16mm, providing greater airflow for the CPU fan intake underneath. A quick and crude CPU stress test resulted in a 4°C drop in the 'balanced' mode -…
Build a rack for dropper paint bottles (such as Vallejo 17ml or Army Painter 18ml) using 4mm rods or dowels. 3 rods simply clip or slide onto the brackets, holding bottles at a 40° angle and a total height of 63mm (for Vallejo). Multiple…
Simple open wall mount designed for the Raspberry Pi 3B+, Pi 4 and Pi 5. All ports and pins are accessible. No additional hardware needed; the Pi is held in place firmly by 3 clips. The Pi 5 version has one clip in a slightly different…
Designed for the Elegoo Saturn 8K. Extends the arm which triggers the Z endstop by 2.6mm. Recommended after installing a flex plate, such as the one from Wham Bam. Slightly longer M3 bolts are needed. M3x8 are ideal. M3x10 might work, but…
Frame for the 4.3'' Bigtreetech PITFT43, with optional mount for the Anycubic Mega. Useful if you're running Octoscreen or Klipper. The frame and back panel mount clip together, holding the screen in place. No additional hardware needed.…
Designed for the cheap ‘130000 RPM’ turbo fans you find on AliExpress, specficially this one . May also fit variants of this model - handle base dimensions measure 42x26mm. Symmetrical design so blower can face either left or right. Step…
Mount IKEA's magnetic Hultarp knife rack to the Skadis pegboard. No extra hardware needed, just a flat head screwdriver to twist in the pins. Print one of each pin. The orientation of each corresponds to the holes in the Hultarp's…
Wall mount for the SX10 10-port multigigabit Nighthawk gaming switch - because Netgear were too preoccupied adding LEDs and as many angles and as possible to this thing, they forgot to add a couple wall mount holes in the bottom, like…
Remix of Petrzmax's bearing holder ( https://www.thingiverse.com/thing:2791727 ) to fit the Igus RJZM-01-08 8mm drylin polymer bearing, which has an overall diameter of 16mm. Inside notches keep the bearing securely in place. Additional…
Are your Corsair LS100 light strips falling off your monitor because the adhesive pads for the magnetic mounts can’t handle the heat? Simply print a couple of these and add your own adhesive pads/tape to distribute the load. Provides the…
Original side hole is designed to take a flat 30mm split ring. Diamond-embossed surface is 0.1mm deep. Dimensions (minus raised letting) are (W) 43mm x (H) 70 mm x (D) 5mm. Various versions included.
If you have customised your Anycubic i3 Mega and have removed the metal surround holding the fans, the x-axis home switch now just about gets touched by the back edge of the carriage. This block provides a more solid push and simply…
This is for the 5-inch version of the Raspberry Pi Touch Display 2 (SKU SC1975) only. Orientation is landscape only, but either way. The default is as pictured but you can mount the other way around by mirroring both parts in your slicer.…
This is for the 5-inch version of the Raspberry Pi Touch Display 2 (SKU SC1975) only. Orientation is portrait only, but either way. The default is as pictured with USB and ethernet ports at the bottom. The (alt) version puts the ports at…
Fit a circular polarising lens filter to your Thinkware F770 Dash Cam. There are 2 versions: – Generic 24mm CPL – Plenty of these on eBay and very cheap. Remove the adhesive magnetic ring before fitting. Filter has a thread for adjustment…
This model restricts the flexing of the power out connector on Razer's laptop power supplies. Excessive movement eventually caused the plastic connector on mine to split at the 90° angle. Since the connector/cable is non-replaceable, this…
To wszystkie aktualnie dostępne wyniki.
![Raspberry Pi Touch Display 2 (5-inch) IKEA Skadis Mount [Landscape]](https://media.printables.com/media/prints/d8f2185d-8d93-4d56-b7db-91d7a4c6d2e0/images/10545358_850dc1e1-1e87-471a-9fb6-b630a37dcc96_caef782c-545b-4a0c-8195-e97eee7cd5ff/piska1.jpg)
![Raspberry Pi Touch Display 2 (5-inch) IKEA Skadis Mount [Portrait]](https://media.printables.com/media/prints/4647eded-2d3e-4bf5-aea1-cd627f643d40/images/10559063_22863cf8-b10b-49dc-aab1-930c80db22ef_11381227-ccec-4eb0-89ad-8e68549bf03f/piksp-1.jpg)
