Liczymy pasujące modele…
This is a sculpted blender model of a hand that I'm working on for use in a future project. The model stands just over 7 cm tall and prints well without support. How I Designed This Starting with a simple two dimensional model of a hand…
A Phantom of the Opera style mask that I designed to be hung on the edge of a picture frame or mirror. It is based on the one that is actually worn by the Phantom in the show/movie so is the half face mask and as such should sit on the…
An Army of Two Mask that I'm working on. I've only printed this on a small scale so far, but it's looking good at this stage. One of my first more serious projects in Blender built from photo references. The next step will be to compare…
A configurable motor mounting bracket/firewall for attaching electric motors to Remote Controlled aeroplanes and so on. It was designed to allow easy attachment using hot-glue, cable ties or fixing screws -- or all of the above if you're…
This is a collection of brackets designed for use with the generic interlocking pegboard system that seems to be available from a variety of vendors such as Lidl, Parkside, VonHaus and TecTake, among others. I believe they're pretty-much…
This is a skull I worked up in Blender based on a drawing that I had seen done. I haven't tried printing it yet but I'd suggest that you use support on the lower layers - and please post a picture if you do. Category: Sculptures
This is a design for a surfboard that I worked up. It is a high volume 5 foot, 6 inches 'baked potato' style board with double concave at the tail - and I wouldn't suggest that you try printing it unless you scale it down substantially.…
This is a corner bracket for mounting a Satellite Speaker to a wall. Print in ABS, support free. To use this you'll need one M3 Bolt (about 16 - 20 mm), an M3 nut (not nylock), two wall plugs and two screws to match. After fitting on the…
A range of custom FCS style surfboard fin plug to fit the original FCS type plug fins. Measurements were taken from some spare plugs that I have sitting around from a previous board build. I have uploaded a range of commonly used cant…
This is a design for a flexible housing or cover that protects the Furious FPV V3 module when used in the Fatshark Attitude V3 FPV Goggles. It offers some impact and weather protection over running the module uncovered and adds some…
This is a holding bracket designed to support a phone upright, or a small tablet sideways. It holds the generic circular Wireless Qi Chargers with space for connecting and routing a USB cable. V9 has further cuts to reduce material use,…
A selection of surfboard plugs for attaching a surfboard leash to a surfboard. The _thin file totals 13mm depth, while all the other ones have a depth of 15mm. Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2…
This is a micro FPV Hexacopter Frame design that I've been working on for use with 8520 coreless motors. The idea is to get a little more lift when carrying the 750 mah 1s batteries that I'm using over what the standard quad setup seems…
These are a set of end caps for a DC Power Supply that takes mains voltage down to 12v. The front cap has apertures for banana plugs (x4), a switch to turn the unit on and off and one for the mains cable. I believe the supply is a fairly…
Two versions of a part designed to replace a missing lower fixture on a hanging ornamental lamp shade. The V12 is 10cm in diameter and about 2.5cm in height while the V13 is scaled at 70% approximately. Both are designed to have an M4…
A spacing bracket for fixing doors that fail to latch. I've included an OpenSCAD customizer file if it's any use to anyone else. STL file dimensions as follow: thickness = 3; outer x = 18.5; outer y = 56; inner x = 12; inner y = 24; screw…
This is a mounting system for a securely fixing an XT60 adapter in place to an Emax Nighthawk 250 frame at the back. The mount holds the XT60 in a vertical position which fixes the battery cable in position out of the way of the…
A hinged bracket designed to carry an E3D V6 extruder. This remix adds a hinge system that opens to approx. 90 degrees to allow easier/quicker access for maintenance. Instructions Print it all at 0.2mm with 20 - 25% infill. Support…
This is a customizable module that I've been working on to allow you to build a propeller duct system. It is research based and should give you a noticeable improvement in duration and/or power from your system (if you can keep it fairly…
This is a cover for a custom power supply for my fatshark goggles. The case is designed to enclose two Turnigy 5000 mAh cells (single) that have been wired in series to make a high capacity 2s battery. It should only require one 16mm m3…
This is a bracket for mounting your GoPro/generic GoPro looking 'Action Camera' securely to an Emax Nighthawk 250 Quadcopter at a 20 degree angle. If anyone wants any different camera angles let me know and I'll work up some other…
This is a case that is designed to fit in to the elasticated section of my FatShark goggles. It's really simple to use - fit the buck converter in place, hot glue for stress relief on the wires and then use 2 - 3 cable-ties/zip-ties to…
To wszystkie aktualnie dostępne wyniki.
