Liczymy pasujące modele…
The Mechanic DT3 USB cable tester PCB confirms continuity on a variety of cables with USB-A, Micro-USB, USB-C and Lightning connectors. This is a case for it. The PCB fits in snug and the lid is a friction fit. If you want the lid more…
This is the screw that holds the spacers on Joseph Joseph adjustable rolling pins. Another user has created an intermediate sized disc and wall hanger for this rolling pin: https://www.thingiverse.com/thing:4849040 Print Settings Printer…
In the age of glass panel avionics, many of these wonderful Swiss 8 day mechanical clocks are being removed from aircraft to gather dust on a shelf somewhere. I had two sitting on my desk and thought to myself that they would make a nice…
Mooney aircraft have a fuel selector which has a control inside the aircraft to actuate the drain to check for contaminates. Without help or a large bucket, there is no way to drain the selector without dumping expensive avgas on the…
FOR USE ON THE GROUND ONLY This scoop fits the pilot side window of my Mooney M20F. It has a lot of clearance so foam weather-stripping can be installed to protect the window and give a more snug fit. If you have good bed adhesion, you…
A thinner holder for simplifying installation of nuts behind Neutrik D-Series panels. This allows for shorter screws to be use.
I am back once again with a replacement part for my Umlo V111 rechargable stick vacuum! The original HEPA filters are no longer available for purchase, so I had to come up with a new solution. This replaces the original HEPA element with…
The original stand for this router was only connected by a thin piece of plastic which was essentially non-removable once installed. I made this cradle type stand. It has 3 strips that get glued in which I printed from TPU for some grip.…
This is a shield to separate the ADS-B radios from the GPS receiver in a Stratux GPS / ADS-B receiver. These UBlox GPS receivers are fairly well shielded, but I have found that the additional shielding helps a bit. Designed to fit in the…
These are ear cup cushion rings for Sennheiser PXC550 and PXC550-II headphones. They allow aftermarket ear cushions such as Brainwavz to be installed without the ned to cut up old cushions. Print the ring with the thin inner edge down as…
Baratza sette is pretty messy when grinding into the stock bin or direct to a portafilter. This uses a little cup which can directly dump the ground coffee into a 58mm portafilter. This is the cup I remixed it to fit. It might fit others.…
I had the need to travel with some of these Sennheiser 6000 series batteries. The TSA requires that LiIon battery terminals be protected. These caps have a a locking tab to secure them to the battery. They come of easily when squeezed…
I needed a microphone stand mounted inline switch for a microphone. I built it into a Neutrik NA extruded aluminum enclosure (it's also available printable). This print surrounds the outside of the aluminum housing. The lower half takes a…
I have an Ender 5 Pro which onto which I have installed a Biqu H2 direct drive. I have a custom spoolholder mounted midway up the frame which feeds the filament up through a reverse bowden setup. This bracket utilizes the old metal…
Needed a set of gust locks for the airplane… Print two flat ones per control surface. Buy one M4 Stainless all-thread per lock: https://a.co/d/c7f4P4Z Grab some M4 stainless wing-nuts: https://a.co/d/4kXngE8 I'd also suggest some fender…
One of our RC Monster truck treads came off and was subsequently lawnmowed. I whipped this up in Fusion. It's not an exact replica, but close enough. Print in TPU, trim length to fit and glue on.
This is a cover for Tascam DM-24 DM-3200 expansion port holes. Useful if you remove expansion cards, no longer have the covers, and don't want gaping holes in the back of the mixer. Print Settings Printer Brand: Creality Printer: Ender 5…
Back plate for https://www.thingiverse.com/thing:4666567 to fit Sensorcon Inspector CO detector. Print the bracket from the original thing. You will need a longer screw for mounting the back plate to your detector. Print Settings Printer…
A stand for a Tascam DR100 field recorder on it's side. It has enough height for Micro USB to be plugged in while in use. Maybe a little too chunky for some people, but I wanted it to be durable. This may fit other field recorders or…
These are card holder/organizer replacement trays for Super Duper Publications 'Grannies Candies' educational cards. I have uploaded two sizes for 12 and 15 stacks of cards cards respectively. Print Settings Printer Brand: Creality…
To wszystkie aktualnie dostępne wyniki.
