Liczymy pasujące modele…
Files now Updated to Version 4 with two more flexible springs. This clamp if fully printable, using printed pegs instead of metallic screws. I also made other changes to make assembly easier. Build Parameters Filament - PLA Layer…
PLA / 0.3- or 0.4-mm layer height / 2 perimeters /15% Gyroid In-fill /No Supports Recommend staggering seams to increase strength Note: On 11/20/25 added a slotted version of the “Pull” that can be pressed into place. This makes…
This model was inspired by a combination of other models one by 3DPRINTINGWORLD , who included a method for giving the prints a Pantene finish ( https://www.thingiverse.com/thing:3783279 ) and the other LoboCNC…
A clamp based on a planetary gear set that is useful as a mini-vise. I increased the overall size and modified the design of the jaws to eliminate the need for supports and increase clamping area.
I upgraded the original design by using printed pegs rather than metal fasteners, including a spring force via rubber bands (so the lower jaw opening follows the thumb screw) and smoothing out contours and working out required support…
This is a high gripping force clamp configuration (relative to other FDM versions) that was re-engineered to included the following features Triangular Cross-Section Threaded Drive Rod. This insures the drive rod is always centered in the…
This is a remix of the Low Poly Tensegrity Dragon by Mochi115 . I liked the concept of the tensegrity dragon with one tension and two support elements. I made the following changes Modified dragon model Eliminate need for supports Add…
See " Assembly Instruction " sheet for details.
Filament - PLA Color Changing, Silk Layer Height - 0.3 mm Perimeters - 3 Infill - 15% Gyroid Supports - Definitely NOTE: Joint was intentionally made tight (0.15 mm clearance per side). You may need plyers to fully seat it.
This is a stylized version of the JWST with an enlarged primary mirror with enhanced curvature, since that is the most striking detail of the telescope.
Used black & white PLA filament Body & Spindle - Black PLA Hands - White PLA Chest Plate - First 2 layers While PLA & Remainder Black .3 mm layers / 2 perimeters / 15% gyroid infill / no supports
Steam Punk geared light switch made from multiple 3D printed gears & hardware. Note that it is designed to fit over the existing wall cover for safety considerations.
Basic Info PLA 0.3 mm layers (I did locally refined the layer height for the retention features on the shaft) 3 perimeters 40% Infill
Glow-In-The-Dark Dragon (or not depending on filament used) PLA / 0.3-mm to 0.4-mm layers / 2 perimeters / 15% gyroid infill / no supports
Scaled up version of 10 HaloMaster343 with joints re-sized and integral supports added so it works well at this size.
Easy to assemble and incredibly strong locking pliers.
PLA/0.4 or 0.3 Layer Height/2 perimeters/10% gyroid infill Head: Recommend organic supports for overhangs Shaft: Recommend brim to anchor part during build
I liked “Teaching Techs” concept but thought it could be significantly simplified. I initially evaluated just reducing the Guide Rails to 2 but then decided also to eliminate the joints in the model. The Adapter aligns to the front of the…
Simplifed design that reduces the weight and improves the strenth of the cable wrap.
Adjustable stand to hold laptops in vertical position for storage or use with a separate monitor. Build Info: PLA 0.3 layer height 2 perimeters / 30% In-fill/no supports
Simple & low filament usage Cat Ears to apply to pumpkin PLA 0.3- or 0.4-layer height / 2 perimeters / Brim Recommended / No Supports
Rev A of Shear added 10/14/23 per request for sharper shear. Rev B 11/23/23 - Removed redundate file and added “Handlle” file which includes only the handle w/o the shear. Layer Ht = 0.3 mm Perimeters = 4 Infill = 40%
A holster for heat gun or hairdryer that prevents the hot nozzle from touching the table or holster. Attaches ridgidly to table.
This 3D printed assembly is used to raise an Amazon Alexa Echo Dot (V2) device and aim the speakers toward the room for facilitate it hearing commands.
Design meant for single extruder printers. Material - PLA Layer Height - 0.3 to 0.4 mm Perimeters - 3 Infill - 15% gyroid Supports - Used organic supports on the trays only For contrasting colors shown, change filament color at these…
This modification moves the pivot point of the idler pulley aft so the adjusting fastener is parallel to the Y-belt at the mid-point of the adjustment range. I also added barrel spacers to allow better load transfer at the adjustment…
This is meant as an educational tool to demonstrate a grasping mechanism for a robotic arm. I used a remix of the “Flexible Grippers” by PrintChallenge but implement with a method for faster actuation so the way in which the compliant…
Increased the kill potential of conventional battle tops Material: PLA Layer Height: 0.3 - 0.4 mm Perimeters: 2 Infill: 15% Gyroid Supports: Recommend Organic/Tree Supports for Launcher Hanle Only Parts Sanp Together - No Glue Required
I liked the concept used by G.Design but wasn't comfortable with the adjusting fastener being at an odd angle to the belt load and that the head and nut would not be fully engaged in the load transfer from the belt tension. By moving the…
Used PLA but PETG might be better choice. 0.3 - 0.4 mm layers / 4 perimeters /15% gyroid in-fill /supports required (recommend organic supports)
This model has several unique features including The threaded driver rods have a triangular cross-section which maximizing build surface contact while minimizing filament use and build time. This configuration ensures there are always 3…
PLA Layer Height = 0.2 mm Seams randomly located
This Dino Shaped Paper Towel Holder is designed to accommodate a wide range of shelf thicknesses w easy installation. The lower jaw slides on a rail to adjust to the shelf thickness. Temporary installation is achieved with cable-ties run…
For this device, I reverse engineered a glue gun feed mechanism to allow a small amount of the greasy dog treat to be dispersed with each trigger pull while maintaining a sufficient grip to prevent my dog from pulling the treat out…
Made with PLA Layer Height = 0.3 or 0.4 mm Perimeters = 2 Infill = 15% Gyroid Supports: Used paint-on organic supports for the bottom vertical and horizontal star points Recommended using paint-on seams so seams follow edge of star &…
Pla / 0.3-0.4 mm layer Ht* /2 perimeters / 15% Gyroid Infill / No Supports - Recommend using 0.2 mm layer Ht for upper 4 mm of each piece if variable layer Ht is available.
These models are easy to print and pleasant to hold & fidget with. The noise can be distracting for bystanders though! I wanted to explore how adding an additional channel and stops to pass-thru objects turned them into an entirely…
These are various devices I have come up with to help the grandkids (&/or parents) un-do the release buckle on car seats. All work but every kid seems to have their own preference.
I modified the base to channel the air better and added a handle for stabilizty. All other hardware per LoboCNC original design. See his URL for projectiles: https://www.printables.com/model/405948-whomp-squadron-and-launcher
Recommend color changing, silk filament. Base only required if handing ornament with a tea light. PLA / 0.3- or 0.4-mm layers / 2 perimeters / 15% gyroid infill
Produced from PLA Layer Thickness - 0.3 mm Perimeters - 3 Supports - 1 Integral Support Included on Base. Remove After Printing. Infill - 15% Gyroid
This device can be used to retrieve a Disc Golf disc that has landed in water, a tree or other difficult to access location. It has a ramped front on the jaws to allow it to easily slide under the disc. Once the disc taps the flappers the…
I made DFliyerz's filament guide but had difficulty installing the Teflon insert so I modified the region for the insert and also remoddled the moving joint to smooth out the shell. Works great especially with full spools of ungainly…
A holster designed for a Harbor Freight heat gun but also can be used for a hair dryer. It is meant to be attached to the side of a desk, table or workbench. The Small Bolt adjust the position of the Lower Jaw to contact the edge or side…
Model captures Shuttle, Solid Rocket Boosters and External Tank suspended by a Cross-Hatched filament pattern within a Frame with integral feet. Printed in PLA White & Black Filaments .3 mm layers / 2 perimeters / 15% gyroid in-fill Black…
I decided to try an alternate approach to making a pass-through model by changing the form of the guide rail used in Fusion 360. The result is interesting both in terms of the shapes involved (Square & Round) but also since the Square…
A way to keep a tramatic time in perspective during this and future holiday's. PLA - Base - gold PooP Topper - Woodfiled Brown (excellant fiber source) 0.3 mm layers/ 2Perimeters / 15% Infill Not To Be Confused With Sinole!!
This adapter allows the quick and convenient conversion of a built-in cup holder to a platform for a ball-mouse. I use rubber bands to help keep the mouse stationary.
Reduced print time by using a ball joint in the thumb which allows it to be laid flat on the print bed. Modified the tendons from a continuous layer (in the original these were single, unidirectional filament layers which readily…
PLA 2 perimeters / 0.3 mm layers / 15% gyroid Infill / No Supports I have also made a launching ramp so the robots can race located at: https://www.printables.com/model/1237930-rolling-robot-launching-ramp
Collapsible Wand for Halloween PLA / 0.3 mm layer ht / 2 perimeters / 15% Gyroid infill / Supports on Handle (see figure). Assemble as shown in figure. A short piece of 1.75 mm filament can be used to lock the end cap in place. Note: Wand…
This assembly allows my cat to get into the room that contains the litterbox while depriving our dog of equal access. It can be adjusted fit the width of typical, interior, non-load bearing walls. I initially considered putting it through…
Was designing a suet holder with a key latch to hold shut. Unique feature is the integral swivel latch which allows printing a strong latch key directly from the build surface and then lets the key rotate into position. The swivel joint…
This fixture holds WORX 20V Max Lithium batteries and charger. It is meant to be mounted on a wall near an outlet. Materials - PLA Layer Height - 0.3 or 0.4 mm Perimeters - 2 Infill - 10% or greater Supports - Yes NOTE: Verify your…
I was inspired by @JakubLattenberg "Flying Kite Reel" that used a print in place reel assembly but wanted to design one with more capabilities that didn't require metal hardware. PLA / 0.3- to 0.4-mm /2 Perimeters /15% Gyroid Infill / No…
Very Important - Print with glow-in-the-dark filament otherwise the warranty is voided! Layer Height = 0.2-to-0.3 mm Perimeters = 3 with scarf joints Infill = 15% Zig-Zag
PLA / 0.3-mm layers/15% gyroid infill/2 perimeters Recommend using brims for Pins & Axel and using organic supports for Travelers Assembly per graphics
This adapter allows connection of nominally 200 mm (4 in) to 150 mm (3 in) downspout extensions. Prusa PETG Layer Height = 0.4 mm 3 Perimeters / 25% Gyroid Infill
This model both lowers the height of the shower head as well as allowing the head to swivel to different positions. PLA 0.4 mm Layer Height 2 Perimeters 15% In-Fill
I was making an opening in an interior, non load bearing, wall and needed a way to transfer the opening size from one side to the other. I used a 1/16" diameter x 6" long drill bit to transfer the corner locations of the opening using…
I decided the Rolling Bobble Head Robot needed an appropriet launching device to allow racing. The robot builds are located at https://www.printables.com/model/1237910-rolling-bobble-head-robot PLA / 0.3 mm layers / 2 perimeters / 15%…
The X-33 was a protype Single Stage to Orbit (SSO) vehicle that was to being developed under a NASA funded project to Lockheed-Martin Skunk Works. Unfortunately, the project was canceled prior to demonstrating a launch. The model consists…
PLA / 2 perimeters / .3 or .4 mm layers / 10% infill / 3 layers for upper & lower surfaces Need supports for chin, eyebrows & neck bolts. Note: For Two-Tone effect, change filament at 68 mm in height.
This Quick Spindle Lock was maade for use with Spool Holder shown at https://www.printables.com/model/474152-mk3s-spool-holder-upgrade/comments/868896 but it should work for similarly sized spool holders. It can be applied to the spindle…
My grandson's Supersoaker stopped working so I disassembled it and flushed out debris that was clogging the intake hose. I decided to make a screen filter for it by using a grid infill pattern without solid layers on the bottom and top.…
I wanted to raise the UPS powering my computer above the carpeted floor to prevent overheating. A pair of these accessory parts raise it ~25 mm above the floor. The design was made to fit a CyberPower 350 VA UPS but can easily be sized up…
Designed a transition from the body to threaded region that contains an array of slots that act as an internal wipe tower to minimize potential for filament bridging around the internal circumference. Used “GetPrototyping’s” approach for…
A way to pass some time. PLA/0.3 mm layers/3 perimeters/15% gyroid infill Note: The knob on the handle will spin once freed up after printing. If necessary, protect the know with tape or paper towel and carefully use plyers to make rotate.
To wszystkie aktualnie dostępne wyniki.
