Liczymy pasujące modele…
This is pretty much the 3D build I used to complete my FlashForge DIY enclosure kit. I used Orca Slicer 2.2.0 for the slicing and muddled my way through the free consumer version of Autodesk Fusion for the design mods. For parts I created…
This design allows you to add the recirculating duct found in the FlashForge Adventurer 5M Pro to the base model. This is probably only useful if you've already added the enclosure or are planning to as it just recirculates air inside of…
Small enclosure for LM2596 Buck Converter. I used this to drop 24V of AD5M printer PSU to 12V to run an exhaust fan for printing ABS, ASA and POM. Since this was external to my system I wanted a fully enclosed cover for this little…
A set of o-ring picks useful to help remove/install o-rings and seals in delicate equipment (i.e. mountain bike shocks/forks) that might be scratched by using metal. I realize there are plenty of designs already out there I just wanted to…
Basically combined a sunshade clip and sun glass holder for those of us with sunshades and sunglasses in our MY's. I'm sure there are a zillion ways to refine this and further improve it but it seems to work. Any heat tolerant filament…
Simple (and cheap) tools that allow you to remove the lower legs on your Fox mountain bike fork. Just unscrew the 10mm (air spring side) and 15mm (damper side) nuts a few turns and use these tools to gentle tap loose the damper and air…
Parts required: 4L Plastic Storage Container (https://www.amazon.com/dp/B09ZLBJQDW) This design is custom fit for these container tops so be aware if you get something else, it may not fit and will need to be tweaked. 2x 608 bearings…
Just another one of the many 3D printed tools used to set the IFP depth found in most oil damped mountain bike shocks. Printed in PLA with default settings as the tool undergoes little if any stress. I did use a "fine" layer setting of…
Volume spacers for 2024 Fox Float shock (https://ridefox.com/products/fox-float-performance?variant=45782556836064) used to reduce positive air chamber to prevent shock bottom-out on bigger hits. The Fox Float series of shock is the baby…
These pads are used to protect the frame and battery on Tesla Model Y's and Model 3 's from jacks and lifts. This design works on vehicles generally made before 2023 that have a jack point hole diameter of 25mm. According to Google, Tesla…
I printed this model in PLA at 100% infill since these are constantly exposed to fairly high air pressure within the positive air chamber of the fork. Air leakage into inner voids of the 3D print would negate the entire reason for having…
Lost my original sag indicator so decided to make a new one from recalling what it looked like. Mounts onto Fox DPS/DPX2 with zip tie and allows you to measure the shock sag. I've place 1mm marks from 5mm to 18mm with heavier marks at…
Just another set of mud guards for mountain bikes. The front ones should fit a Fox 36 fork and the rear has been somewhat designed to fit on a 2019 Pivot Trail 429 but could easily be modified to fit on other frames. Print in PETG with…
Sag indicator for Fox Float (2024+) and Float X. This does not fit older Fox Float shocks (pre 2024), DPS or DPX2. Not sure if it fits the XC oriented Float SL shock which I believe is a refreshed version of the DPS. The uploaded STEP…
Introduction: I created an enclosure heater for my Flashforge Adventurer 5M and modified the front left riser in design8studio's minimal DIY enclosure to incorporate a temperature controller and two fan speed controllers (one for heater…
VERY simple remix, just removed the tabs and added Tesla Logo to make it extra dorky! Printed mine in PETG and although you can get away without supports mine was very “stringy” on the cantilevered parts as also reported by others. Also…
After one of the plastic exterior handles on my garage door broke I decided to try and design my own and 3D print. The original one is injection molded, very rigid any shiny and likely made from Glass-Filled Nylon (PA-GF). So after…
Replacement final drive gear for the sidebrush and roller brush pulley of a Eufy G30 Edge robovac (compatible with many similar Eufy models). These gears seem to strip after tangling with too many cat toys, lol! Orca Slicer Settings…
After upgrading my 2019 Pivot Trail 429 to 12 speed, I occasionally would get my chain wedged between the bottom bracket and chainring so badly that I'd have remove the crankarms to free it. Thankfully this has only ever happened in the…
I lost the sternum strap on my Camelbak Lobo (snagged on a limb while riding), so I designed and 3D printed replacement parts to build a custom assembly. Unlike the original design, this setup replaces the magnetic tube holder with a…
To wszystkie aktualnie dostępne wyniki.
