Liczymy pasujące modele…
This is a simple shaker/mixer that attaches to your hand drill (corded/cordless) to drastically speed up the time it takes to mixing of a can of spray paint. No longer do you have to shake the can manually for a minute or more. I've…
Replacement bung for 210L/55 gallon poly barrels that have a coarse buttress type thread, not NPT fine thread. The OD of the bung cap thread is approx 56mm. Included in model is a bung cap with/without hole for 1/2" OD hose, and hand…
This model is specifically for the DELL WD19, WD22, K20A USB-C Thunderbolt Docking Stations (all have the same 9cm deep x 2.9cm height case) and allows the dock to be clamped to the edge of a desk and hide all the associated cables. I…
The chuck stop was made for my Hare & Forbes AL-320G / L141 metal lathe (Model available within Australia) to locate shorter parts beyond the chuck jaws to provide clearance for facing operations. It has been designed for the standard…
Simple dust cover for a combination of Anderson SB50 (50Amp) and 7 pin flat (Type 3) trailer plug (Australia/New Zealand). TWO models included - for 1x Anderson plugs and the cover for just the 7pin connector. For 12 pin plug version, see…
This is a simple tool holder for BXA size quick change tool holder for any lathe. This similar to other tool holder designs uploaded, however this is specifically for lathes with a backsplash panel of 25mm width - the dimensions not…
This is a simple riser to provide a more open area underneath for the ventilation/cooling intake fans as these laptops can run quite warm. It also serves to angle the laptop approx 5 degrees to provide more comfortable typing position.…
Simple feet to replace the original inserts in a standing/pedestal fan with rectangular shaped legs. Keeps the legs raised off the ground by approx 6mm Dimensions of the rectangular shaped legs is 22mm wide x 38mm high
Simple dust cover for a combination of Anderson SB50 (50Amp) and 12 pin flat (Type 3) trailer plug (Australia/New Zealand). THREE models included - for 1x and 2x anderson plugs and the cover for just the 12pin connector. For 7 pin plug…
This is a tool to aid in setting panel gaps when fitting car doors, bonnet/hood or boot/trunk and utilises round magnets to hold the tool in place. The STL model files here use either 10x3mm or 12x5mm (up to 12.5x5mm) round magnets for a…
Simple dust cover for Australian / New Zealand flat 7 pin trailer plug. Limits dust & moisture getting on the pins, however I also added some dielectric grease in the holes to prevent corrosion also. Remixed from…
Basic case for single DIN car stereo detachable faceplate / fascia. The interior of the case is 172L x 49W x 30H and should hopefully suit all detachable faceplates, including those that have large front knob. The hinges use a short piece…
Some metal storage cans used for storage of flammable liquids (such as gas/petrol, thinners, paint materials) have a 45mm OD outlet however it's not a DIN45 thread as used on plastic petrol containers, as the thread depth is only about…
This is simple wrench for removing/tightening the fuel filter housing cap on a Holden RC Colorado and Isuzu DMax (2008-2011), where the filter is located underneath the vehicle next to the LHS chassis rail. The wrench has a hex nut of…
When fitting and aligning the doors on my Classic Mini by myself, I was struggling to maintain keep the door position when making minor adjustment to the alignment. I designed this two-piece clamp to hold the window frame. The upper piece…
Classic Minis are prone to rusting at the bottom of the rear quarter windows and often need rust repairs and filler/sanding. This is a simple sandpaper holder for sanding the radius of the lower section of the quarter window opening even…
Simple storage holder with lid for storing old-school car glass fuses in your glovebox. Designed to store 3AG (32 x 6.3mm) fuses. Version 1 is rectangular box with friction fit lid. Models available for 6x or 8x fuses Version 2 is a…
Remix of https://www.printables.com/model/41929-slim-wand-for-dyson-v8 and modified to be much shorter (sticks out approx. 90mm past the vacuum body) Assembly instructions are in the original model
Remix of https://www.thingiverse.com/thing:4827340 trailer plug tester idea but approx ⅔ the size of that model. Designed to simply insert into the trailer connector/socket on your vehicle and get someone to cycle through the…
I've had a 8L oil drain pan for a few years now and the spout area was so badly designed/shaped that you had to pour out the oil reeeally slowly otherwise it would spill over the edges. These drain pans are sold in Australia (as copies)…
Simple feet made to replace standard rubber ones that have worn out and cracked on my old multi-purpose foldable aluminium ladder, where replacement feet are no longer available. The design is the same shape & profile as the orginal feet,…
I purchased a few cans of car underbody sealer however they had pull ring to open them but no way to seal them again (no cap/lid). This is a simple cap for sealing those cans - the ones that a Schutz gun screws into when spraying bitumen…
Simple cap keeper for camping gas / LPG / propane bottles (1.25/2/3/4 kg) that have a 3/8" LH thread and plastic valve cap - supplied with the Companion branded cylinders (Australia). The keeper securely presses into the plastic cap…
When replacing a steel A-panel in a classic Mini, it's important to get the two holes in the new A-panel aligned correctly so the external hinges fit, and this is what these models are for. How to use these templates : Confirm what side…
This is a compact glovebox storage box for spare automotive Standard or Mini blade fuses. In each model there are slots for 8 fuses and a fuse puller (various puller models are readily available to download print). There is a small hole…
Commercially available magnetic sweepers are usually 600mm / 2ft wide and too bulky for my small home workshop. My solution was to design a smaller version (which ended up being approx 235mm wide) that can get into smaller areas and be…
Sealing ring for a Kambrook BlitzPro blender. I needed 3x and was not prepared to spend $15ea for the factory silicon sealing ring replacements. The seal inserts in the lid or base (with the blades). The seal has an OD of 98mm and may be…
Storage bottle designed to hold small single-shot (1mL) super-glue / CA glue tubes and prevents moisture ingress and glue from drying out. I use the small tubes of superglue sporadically and wanted a simple solution to stop the remaining…
Remix of animal/wildlife bottle feeder mount for Original design was modified to suit : - 100mL SQUARE shape "Grow" feeding bottles - 4x 10x3mm magnets See the original design for ball joint & collar to complete the set of 4 pieces per…
Two simple boxes to make it convenient to store Petsafe bark collars : PetSafe citronella collar, charge cable & (up to 4) spare cartridges. This is for the model that uses citronella cartidges. OR PetSafe rechargeable bark collar &…
To wszystkie aktualnie dostępne wyniki.
