Liczymy pasujące modele…
This Plant Label for garden plants can be printed in PLA without any support. Edit 09/2022: After this summer I would no longer recommend printing this in PLA. In my garden multiple lables bent down due to the intense sunlight heating up…
These spoons can be used for measuring small volumes e.g. in the kitchen. Values are: 0.1 ml 0.2 ml 0.5 ml 1.0 ml 2.0 ml 5.0 ml Note: The Spoons are not marked or labeled. It is advised to label them e.g. with a label maker. Notes: I used…
Stand for my FritzBox 7530 AX to keep it at 35° for reduced footprint and better status-LED visibility. There are four notches and two stubs to mechanically interface with the router and hold it in place. On the bottom side there are four…
This is a faster-printing version of the Planter-Pot Spacer ( https://www.printables.com/model/1540749 ). Like the original, it can be inserted in between the flower pot and its outer pot or planter, to lift the former higher up. This is…
It can be really annoying to try to solder some ICs onto a PCB when the tin-solder wire keeps getting stuck somewhere. But those times are over! Just print out a tin spool holder - now you can keep the spool rolling and the wire coming,…
This is an alternative version to the Water Spike ( https://www.printables.com/model/1233306 ). Instead of dripping water onto the ground, it injects the water into the ground underneath your plants to give them a maximum amount of water…
This is a collection of fan grills I used in multiple projects. They print well with support and are bulged outward, or convex, to make them more sturdy. The disadvantage of this is that you have to remove support structures before using…
This spacer can be inserted in between the flower pot and its outer pot or planter, to lift the former higher up. This is especially useful if the sizes of planter and pot don't match properly. I have uploaded sizes listed in the…
This is a universal Fan Stand which can be used to place a powerbank powered 120mm fan wherever you want. Printing For building the Fan Stand you'll need to print the following parts: 1x fan holder 1x fan holder, mirrored 1x powerbank…
If you have a garden with access to a hand pump you might have run into the problem that you have to hold your watering can with one hand while pumping with the other. Especially for large watering cans this can be quite tiring... But no…
Abstract This is a low-tech, low pressure drip-irrigation system consisting of dripping Water Spikes connected by a 1/2" (12.7mm inner diameter) garden hose. The hose is fed by a Bucket, which you can fill with an ordinary watering can.…
This is very similar to the original model, but I added a 10mm spacer to the backside, to insulate it better from my outside wall. It can be printed on its roof, without any supports - just like the original.
I really like redline's "Fensterstopper", but unfortunately I can't open all my windows fully. To accommodate different maximum window angles, I changed the width of the window opener. See the sketch below. The filenames contain the width…
I've had some problems with ripples in my prints or even missed steps. After some investigation and experimentation I found out that the reason seems to be the sturdiness of the y-axis linear bearing holders - or rather the lack of such.…
Basic Idea I really like mfischer79 's Planter Starter Cups . But in order to save material and speed up printing time, I wanted a thinner-walled version. This is it. It comes in two versions: Version 1 : wall thickness of 1.2mm Version 2…
I looked at the filament mount my Flashforge Creator Pro came with and thought: What if it had ball bearings? So I did a re-design and later added a guide to prevent filament jamming. For a more detailed description see the pictures and…
This is a holder for cartridge fuse packages with 20x5 mm fuses. It allows for the simple storage and organization of fuses.
Holder for hygrometer Idea is to glue it to e.g. a cupboard Hole diameter: 42.5mm
I have no idea whether anyone will need that thing, because its use is quiet specific... I have a few pinguicula plants (or butterworts according to wikipedia). They are carnivorous swamp plants (very usefull against fruit flies) and…
If you have a pollen allergy (like me) you'll know the problem of having to have your medication on you basically all the time. My allergy gets my eyes to water, burn and itch, so I always carry eye drops in late spring / early summer.…
I have a very small dishwasher, so I designed this Dishwasher Tab Splitter to break the tabs in half. Just put the tab in, press the guillotine part in (with some force) and wait for a small clicking sound - the tab breaks in the middle.…
This is a wall mount for the SNZB-02 ( https://zigbee.blakadder.com/Sonoff_SNZB-02.html ) air temperature and moisture sensor by Sonoff . The Sensor comes with sticky tape and is supposed to be taped to a surface directly. If you stick it…
Noodle Scoop to get the right amount of noodles for one person / one serving. Both Penne Rigate and Penne Lisce are marked. Notes: The scoop gives me the right amount of noodles for one serving. You might like to eat more or less and…
A better fan holder to improve the quality of your 3Drag prints.
The standard 3Drag z-axis endstop is pretty inacurate. Just by moving the screw a little to the side, you'll change it's angle and screw up the z zero position - kind of literally. This improved endstop screw holder let's you place two…
Description This is a 140mm version of my 120mm Fan Stand with Powerbank . Please see the original model for a more detailed description. Parts Required Parts For this 140mm version you will need to print: 1x fan_holder_140mm.stl 1x…
Introduction If you have Sonoff's SHZB-02P s you can place them on ferromagnetic surfaces already, since they are magnetic. If you want to stick them to a non-ferromagnetic sheet (like the wall of a plastic container) you'll need a…
I needed to put my picks somewhere and made a little "pouch" to hold them on e.g. the wall or a piece of furniture. I used double-sided tape. Maybe you'll find it useful as well. I recommend printing it standing up with a raft, as it has…
This door spacer keeps your cabinet door from closing fully, e.g. for ventilation. It is foldable, so it is not in the way when not in use. In order to prevent it from closing accidentally, it opens slightly wider than 180°. My…
To wszystkie aktualnie dostępne wyniki.
