Liczymy pasujące modele…
I have a new AD5x printer and found a 24vdc LED JST-XH port on the main board. I also had a couple of Daylight on a Matchstick pcb lights. I designed some slip in mounts to screw to the PCB lights and snap into the side rails of the…
Lots of buckets out there, but I wanted something easy to print, hold a lot of purge, not block the psu venting and easy to grab to dump. Handle needs heated inserts M3 5mm OD x5mm length. M3x6mm screws. The other option is to just drill…
The official AD5x panel kit does not show to use any sort of washers for the screw heads that secure the hinges and door handles. I made these backers to spread the load of the screw securing the panels. This is especially important on…
I do not like the extended top for the Flashforge AD5x and wanted a simple addon to keep the tubes from touching the top. I've designed a part that replaces the accent part in the side panel that the tubes pass through. It clamps to the…
FlashForge AD5x PTFE lined side access covers. Replaces the FlashForge enclosure kit IFS opening trim. This is an additional option to my swingarm guide system. This reduces the gap in the side panel and lined with PTFE tube for friction…
I/O trim plate to for the user port area of Commodore 64 using the Ultimate 64 main board. This slides into the case before sliding the board into it. No modifications or screws needed to hold it into place. I have version 1.2 of the U64,…
I received the updated spools for the AD5x and they work fantastic except that they raise the center of the spool upwards so some of my cardboard spools would rub the IFS with channel 1 and 4 spools. I made this adapter bracket to lift…
I needed a M5 thumbnut for a project, I do not recall what for. Cleaning out my past projects, sharing here before deleting. Category: Parts
Wanted a bumper for my TRX-4 with a Axial Cherokee body on it that would fit in tight to the rear of the vehicle and not hang down very low. I used a bumper mount with very little drop and as far out on the frame as I could get. Added a…
Combined the Automatic lever adapter with the manual lever for the magnetic top mod. This one has a bit extra bracing to box the adapter for a bit more stiffness. Also swapped the open arrow on the manual knob. Features 10mm extension to…
Cover for the 9pin Joystick ports on the C64. Could glue in bit of antistatic foam for tighter fit if needed. I tested this on a C64 breadbin and the Ultimate64. Print Settings Printer Brand: Prusa Printer: I3 MK3S Resolution: .20 Infill:…
Trays that fit the default size of Whity's box to fit a Fluke 16, spare battery, and leads. Also added a handle that installs with 5mm longer screws
I needed a SSD tray to put three ssd drives into the space of two 3.5" bays. These fit my drive sleds for my Corsair 650D case, but should fit in any 3.5inch drive solution. I provided the option to mount a 40mm fan to the tray if…
This is a project box out house a Pro Micro knockoff board and two DB9 plugs to use for Logitech foot pedals and shifters as a standalone USB controller without the need for the Logitech Wheel base. Use your Logitech Pedals with a wheel…
I wanted to make the display of my MK4 to be easily moved from the printer to somewhere outside of my enclosure. I also do not like the screens sticking out the front all of the time. I made a swinging mount for the LCD with quick…
Snap in covers for the Video and Serial ports on Commodore Computers. I have tested the round 64c style inside a Pixel Wizard and original 64c case. I also did test it in a C128 flat case, but its very tight. Might need some sanding or…
plugs for the RF output and channel switch slots on the C64c case. Great for Ultimate64 or pi64s. Simply snap to fit into place. No case modification needed. UPDATED: Now Added Breadbin plugs. Print with supports. Breadbin plugs slide…
Motherboard standoffs to replace cracked, broken or missing standoffs in the bottom of the breadbin cases. I made them extra wide on the bottoms for enough glue to surface contact. Sand down what is left of the broken standoffs. Screw the…
I needed a new striker sleeve on my 1991 Ford Bronco. Should be the same for 80-96 maybe 78 on up but I am not familiar with the 2nd gens. PETG probably the best option. I printed with a brim just to be sure it stuck.
This is a full set of 4 wedges that go under the 4 top row screws of the C128 keyboard. Without these wedge spacers, you risk breaking the mounting holes and the keyboard will not tighten correctly to the top cover. Print Settings Printer…
My cousin needed a plastic arm inside a gearbox that moves the head of a mechanical ride on dinosaur. He gave me the original part he glued together and I designed this to replace it. He said it works perfectly. I do not know what this…
Needed more straight dividers than what comes with the Plano 3771-00 box. I have tested this with Overture PLE and PLA. Print flat as it is with no supports. 10% infill at .20 resolution. Slide in with the tabs towards the top as the…
Simple box to hold an Arduino Pro mini so you can double stick tape inside the C64 case. for switching a c64 multi rom mod. Adrian's Basement did a video of this simple mod. It is a press fit for arduino but you can use double side tape…
I wanted a locked rear drive on a Helion Animus. I created an ez drop in spool to replace the spider gears in the differential. Using the original pin in optional. The spool is clearanced for the tabs on the ring gear. To install, remove…
10mm Crowsfoot spanner. Print flat on the handle, no supports needed. .20 layer height, 40% infill, 4 walls.
Dropped my printer power cord behind the cabinet 4 times in a row. No more. Wall mountable IEC cable hanger. Will save my sanity when doing printer maintenance.
I was making my twitch logo into a case badge for a project and quickly did one for Sadaplays logo. I printed at .15 with 100% infill. The logo I printed face down on textured sheet for a finished look. It is a press fit into the base. I…
A friend asked for tips on installing heatsets. I made him this practice plate for M3 x 5od up to 5mm length heatsets. Best to print with at least 4 walls so the heatsets have plenty of material to slide in.
I do not like gridfinity (gasp) and have no need for it on this awesome press arm. I redesigned the tray to just be a tray with smooth bottom edges to help get things out of it.
To wszystkie aktualnie dostępne wyniki.
