Liczymy pasujące modele…
Here is a little sugar bowl that I designed and printed using woodfil filament, then sanded and finished with stain. It can be scaled up or down in size within your slicer depending on your needs. Print with 2 perimeters and low infill. I…
Remix of safety push stick by Alexis67 https://www.thingiverse.com/thing:779678 I resized to fit on the Prusa i3Mk2S. I added more holes to reduce material usage without compromising rigidity. I made one side flat to lay on bed without…
I made this Artist's Paintbrush Organizer for my wife's many, many paintbrushes. It has compartments of many differents sizes as well as a "tip shaper" for wedging the brush tips. If you found this useful, please consider a SMALL DONATION…
This birdhouse has a 32mm entrance to accommodate wrens or chickadees (other similar sized species as well). It has adequate venting and weather-sealed, the front is easily removable for cleanout. Print it laying on the back wall to avoid…
*** I have revised this design again. I didn't like the original wrist angle and so I changed the grip tilt. Now the your wrist should be more naturally aligned. I also reinforced the fulcrum point to account for the increased angle.…
This birdhouse has a 32mm entrance to accommodate wrens or chickadees (other similar sized species as well). It has adequate venting and weather-sealed, the front is easily removable for cleanout. Print it laying on the back wall to avoid…
I made this replacement slider for the upper track of a bi-fold door. Because it does not have a spring mechanism it requires at least one good slider with the spring to be installed on the opposite door. I recommend that you print it…
This follow-focus speed crank works fantastic! Make sure to CA glue the knob to the handleshaft. There is a print-in-place ball bearing inside the crank lug. I recommend printing the threaded handleshaft vertically using a super wide…
I made these 16mm rod camera rig offset clamps for my homemade teleprompter. There are two different offsets: 19mm and 38mm. I printed them using Overture PETG https://amzn.to/3a2FNll Use a minimum of 40% infill and .15mm layer height. M4…
This birdhouse was a commissioned work for someone special. I modeled it to replicate the ones made with real "gourds" but instead of hanging from a hook, I made the back flat to be able mount to a wall, fence or any flat surface. It has…
I made this birdhouse to accommodate wrens or chickadees (other similar sized species as well). It has adequate venting and weather-sealed, easily removable wall for cleanout. There are two variations, depending on your printer size and…
I created this universal camera mount to sit on the front of my X1 Sidewinder base using the existing hex screw located in the centre of the Y-axis rail. I have two other versions (see below) that this is based off of. With this version,…
I made a simple paint tube carousel / lazy susan for my wife's Liquitex Acryilic Paints it holds 15 of the 4oz, 2oz and 0.74oz tubes and tubes with the same cap size. It also has a smaller recess for holding smaller tubes of paint (brands…
I created this universal camera mount to sit on the side of my X1 Sidewinder base using the existing hex screw. It works great with any of these style of HD webcams and Octoprint:…
I created this universal camera mount to sit on the lower rail of my CR-10 using a t-nut and M5 screw. It will fit on any printer frame that uses 2020 or 2040 extrusions. It works great with any of these style of HD webcams and Octoprint:…
I created this custom form fitting case to protect the X-Rite or ColorMunki display calibration hardware.…
This is a remix of my second version https://www.thingiverse.com/thing:4284169 but I've added a convex bottom so that it can recess for a tighter fit on some gas applicances where the valve protrudes. This one will require a bit of bed…
Modelled in Fusion 360. I made this lens cap cover for my replacement dive housing. I have a Hero 3 and purchased some underwater filters but later leared that they fit the newer style Hero 4 housing which has a smaller lens opening. None…
I made these holders to have my phone sitting on top of my camera in the hotshoe while I shoot so that the phone camera can be recording video while I shoot pictures (without a hotshoe flash of course). I also use it with my Moza Air2…
This is a remix of my original watch band holder: https://www.thingiverse.com/thing:4197989 . Look there for print settings and additional information. I added the AirPods charging dock. It uses the original Apple Lightning cable that…
I first modeled and designed this flash modifier set for my Nikon SB800 Speedlight. The mount fits on the flash and the modifers attach magnetically to the mount for easy changing. The added benefit of using the magnets is that you can…
This is a shallower, less chunky remix of my original one https://www.thingiverse.com/thing:2749492 Print in ABS or other outdoor suitable plastic. Fits standard gas valve keyed shaft found on most BBQs or outdoor gas appliances. I would…
Here is an octagonal bowl that I designed and printed using woodfil filament, then sanded and finished with stain. It can be scaled up or down in size within your slicer depending on your needs. Print with 2 perimeters and low infill. I…
I designed these holder / fixtures for G4 12VDC LED automobile dome lights. Print using PETG for best results. The retainer ring snaps into place firmly holding the LED inside. Solder the wire leads before snapping the ring in place. The…
Print in ABS or other outdoor suitable plastic. Fits standard gas valve keyed shaft found on most BBQs or outdoor gas appliances. I would recommend a bit of acetone smoothing if printing in ABS. If you found this useful, please consider a…
I created these cylinder chambers to make a food dehydrator into a makeshift filament dryer. I made two sizes depending on how many spools I wanted to dry at one time. Here is the dehydrator that I use: https://amzn.to/2y7Nw46 This one…
I needed some method of hanging ropelights around my patio handrail that was easy to take on and off and would be durable. I printed these in white ABS to withstand the winter sub-40°C and +40°C summer temps that we get in Saskatchewan,…
I designed these lightweight heads for my Prusa i3Mk2S to provide a broad cast of light in the front and back. They are designed so that you can have light in the front, the back, or both as the light standards are independant. Small…
To wszystkie aktualnie dostępne wyniki.
