P
PrintablesRotaryFever
Tall sight pusher for Glocks
Modification to spiggytech's pusher tool to install taller sights.
- Pobrania
- 130
- Polubienia
- 14
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesRotaryFever
Very Tall/slim model support tower
This is a support tower for very tall and slim prints. Tall and slim prints are very hard to print even with a large brim. Yes, you can lay tall prints on their side for more strength and easier print, but if you want to print many parts…
- Pobrania
- 126
- Polubienia
- 11
- Ocena
- 5
P
PrintablesRotaryFever
Soldering Fingers (Wire holder) 2x2 Gridfinity base
Remix of Solder fingers and all my favorite additional features from several authors on a 2x2 gridfinity base. -Solder fingers (mistertech) -Need heat shrink reminder; I always forget. (aprilla) -LED holder (JuneBeatle)
- Pobrania
- 105
- Polubienia
- 11
- Ocena
- 0
P
PrintablesRotaryFever
Elegoo Neptune 3 Max Y-axis TBStron3d linear rail guide
The TBStron3d Y-axis linear rails can be a challenge to align. This guide can be used to keep the Y-axis rails parallel to each other while installing the kit. Print 2 of these in PLA. I don't know if these guides will work on the other…
- Pobrania
- 96
- Polubienia
- 19
- Ocena
- 5
P
PrintablesRotaryFever
MegaTronxy Upgrade (Work in Progress)
Naming Convention: Base: I don't intend to change these files unless a problem arises. MK.II (Work in Progress): A complete revision of the gantry and hotend. Intent is an IDEX setup. MK.I: Update 4/19/2025: Never say never… I changed a…
- Pobrania
- 66
- Polubienia
- 10
- Ocena
- 0
P
PrintablesRotaryFever
Biqu H2 Mount for Elegoo Neptune 3
4-7-24: Update: Added A 1mm shorter version of v2 with micro probe called “V3”. I changed the nozzle to E3D brand which is a bit shorter than original Biqu Nozzle. This caused the probe to hit the plate while stowed before the nozzle.…
- Pobrania
- 54
- Polubienia
- 12
- Ocena
- 0
P
PrintablesRotaryFever
1x1 Gridfinity MOSFET bender
Gridfinity THE WORLD!! Trimmed the Bending jig by Marco R then added it and Marcin Kuberski's Transistor Bender to a 1x1 gridfinity square
- Pobrania
- 45
- Polubienia
- 11
- Ocena
- 5
P
PrintablesRotaryFever
Neptune 3 Max Robin Nano v2.2 Mount
Mount for Elegoo Neptune Robin Nano V2.2. Used to move the Nano outside of an enclosure. Has adaptor for the stock fan. Other Models Shown MOSFET: https://www.printables.com/model/630817-elegoo-neptune-3-max-mosfet-mount MAINS/SWITCH:…
- Pobrania
- 34
- Polubienia
- 1
- Ocena
- 0
P
PrintablesRotaryFever
Replacment foot for Jorgensen Pony Sawhorse
Broke one of the plastic feet on my Pony sawhorse. Needed a quick fix. This one is an easy print that just slips on. Adjust scale for tighter fit. Made with PLA. https://ponyjorgensen.com/product/2-piece-clamping-sawhorses/
- Pobrania
- 27
- Polubienia
- 2
- Ocena
- 0
P
PrintablesRotaryFever
Neptune 3 Bambu hotend adapter with BTT Microtouch
Changed the BLtouch mount to use a BTT Microtouch. Made improvements to the hot end adapter.
- Pobrania
- 27
- Polubienia
- 2
- Ocena
- 0
P
PrintablesRotaryFever
Elegoo Neptune 3 Max MOSFET mount
I built a custom enclosure around my Nep3max. Wanted to mount the electronics outside of the enclosure. This part is used to mount the Bed MOSFET outside of the printer. Other Models Shown: MCU:…
- Pobrania
- 26
- Polubienia
- 5
- Ocena
- 0
P
PrintablesRotaryFever
Remix of Semi-Flex Clasp for Spannerhands' filament box
The Semi Flex Clasp did not work out for me when I printed it with 95A TPU; even at 100% infill. Just seemed to flex too much when closed allowing the lid to lift slightly. In addition, I did not want to get 98A TPU and I wanted to use a…
- Pobrania
- 19
- Polubienia
- 1
- Ocena
- 0
P
PrintablesRotaryFever
Shaved Slider for rear sights with red dot installed
This slider allows you to remove the rear sight with a red dot installed. One side is trimmed down to get the screw closer to the center of the rear sight when a red dot is installed. The original slider tends to get crush on the edge and…
- Pobrania
- 12
- Polubienia
- 1
- Ocena
- 0
P
PrintablesRotaryFever
Ruger MK3 Rear sight pusher Adaptor
Slide this adaptor into the back of your MK3 upper. You can then use Spiggytech's Glock sight pusher to press the rear sight. May work on other Ruger variants but I only have the MK3.
- Pobrania
- 11
- Polubienia
- 4
- Ocena
- 0
P
PrintablesRotaryFever
Shower/tub valve backer
My shower mixing valve was clamped to the shower liner using a plastic disc. During removal of a leaking mixing valve I found the plastic backer disc was stripped out and now needed to remove the disc, otherwise the valve was just…
- Pobrania
- 7
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.