Liczymy pasujące modele…
This is an open source armory system. It uses off the shelf louvered panels with 3d printed components to build an armory storage solution of your dreams. It be scaled from a single panel to a complete room. It is a strong and secure…
This a water pot for painting miniatures or models. It has similar features as the Games Workshop water pot. There are grooves on the bottom for deep cleaning the brush. There are grooves on the side for wiping the brush. There are…
Added a loop on his head to attach fishing line for hanging. Shrunk it down enough to fit an Anycupic Photon. Included a version that is hollowed with drain holes. Print Settings Printer Brand: Anycubic Printer: Photon Supports: Yes…
This is a dummy extension for a Ruger 10/22 mag to make it look like a m1 carbine mag. It also makes it easier to insert and remove the mag. After printing glue the extension to the mag. For more information on a 10/22 m1 carbine…
I edited hcpookie's jig to add the holes. Here's the original with the discard tray. https://www.thingiverse.com/thing:5439067 Category: Hobby
This is a belt drive conversion that can be almost completely 3d printed. My mill broke and I wanted to make a printable belt drive. It started out as only a temporary fix, but I've been using it for several months without problems. This…
This is an adapter to use ar mags in a HK33 style rifle. The adapter slips on and locks into the mag catch slot. With the adapter the ar mag works exactly the same as a factory HK mag. This works best with USGI mags. The Fusion 360 file…
This is a bolt tool for HK rifles. Works with HK93, HK91, G33, G3, and Cetme. After printing tap the hole with a 1/4-20 tap. Use a 1" long thumb bolt. Uploaded version 2 of the tool. This one has a slot in the front for the locking latch…
mag_holder_ak is a slot loading mag holder for ak mags. It holds ak47 and ak74 steel and bakelite mags. Vz58, hk g3, and cetme mags also fit. Check out the main page for Open Armory for more information on the system. Also check out the…
I was working on making a Colonial Marines knife from Aliens. I found some pictures of the blade in its blank form. The tang looks very similar to the tang of a file. I heated a file in a 400 degree oven for a couple of hours. Then ground…
This is the inferno squad helmet from battlefront 2. It is cut into 8 pieces for a 200mm printer. Use the .stl file for splitting for a smaller printers. Most of the files ar in .3mf format because stl files were pretty large. In the full…
This is a remix of a jig for aligning the rear sight bracket on a HK receiver for welding. I've made it so that it is held together with 2 screws. I also make some changes to the shape of the jig. After printing run a tap through the left…
This is a smoothed version of Ahsoka Tano scaled for star wars legion. Incuded a version with supports for sla printing. Print Settings Printer Brand: Anycubic Printer: Photon Supports: Yes Resolution: .5mm Category: Toys & Games
This is an improved 1 piece jig for drilling the hole for installing a paddle release. I modeled it to fit tightly onto the Century C93 receiver. It is a snug fit and will require a rubber mallet to fully install the jig on the receiver.…
This is a wall mounted hanger for brooms or mops. Push the handle in from the front and the lever pushes the handle against the grip holding it in. It has enough grip to hold up heavier items like a Swiffer wet jet. It is small enough to…
The original wouldn't hold the belt tight and wouldn't stay on the carriage. Deceased the gap for the belt to slide in. Made the walls wider so it wouldn't flex. Now the belt slides in tight and doesn't pull out. Made the clips to hold…
This is a printable follower for HK G3 mag. This allows you to have one more 922r compliance part. USA is clearly visible on the side. After printing dill out the hole that is filled with supports with a 2mm or 5/64" drill bit. Insert the…
Jig for holding a mauser 98 receiver. The two action screws go in through the bottom and screw into the receiver. The jig can then be clamped into a vice to allow a stable way of holding onto the receiver while working on it. Print…
This is a bolt for a Thompson m1a1. I'm using it in an airsoft aeg to make a dummy replica. I started with a 1928 bolt by MikeS on GrabCAD. I filled in the holes and reworked it using dimensions from a real m1a1 bolt. The airsoft receiver…
mag_holder_ar_usgi is a top loading holder for .223 ar mags. mag_holder_ar_pmag is a slot loading holder for .223 sized pmags. Hk93 pmags will also fit. .223 pmags for other rifles should fit too. mag_holder_ar_marushin is a top loading…
Remixed to hold grinding disks for 4.5" and larger grinders. Works with pegboard clips by stoof. https://www.thingiverse.com/thing:1540038 Included are clips that work with harbor freight pegboards. Print Settings Supports: No Infill:…
These are 3d printed parts that I used while modifying a Snow Wolf Pulse Rifle. I gutted the fake grenade launcher and inserted a PPS 870. Some of the printed pieces aren't an exact fit and will require some fitting. The Fusion 360 files…
I ordered an ak handguard set from Apex to fit on my airsoft replica. The lower handguard is a little out of spec compared to a real one. It did fit the airsoft, but had some play. The rear tab that slides into the front of the receiver…
This is a snap cap for .577 Snider. It is for function testing and loading and unloading practice with the Snider rifle. Once printed sand smooth any bumps or extra plastic. Then try it in the rifle. If it dosen't slide in easily don't…
This is for making an extended cocking handle for a HK or Cetme. The body is made from a 3/16" plate. It needs to be made out of steel. A 3d printed version will break. The model is only for reference. Assemble the cocking handle and the…
This is an adapter to attach a save phace welding helmet to a kask zenith hard hat with jackson quick release mounts. The jackson quick release mounts were cut down to fit in the kask zenith visor slots. Then with a 3d printing pen I…
This is a special award to be given out to someone who after a few drinks becomes a loudmouth know it all thinking that they are on top of the world. It uses the stewie griffin model by alfonsopyro.…
This is a remix of a design by Vaclav Krmela. https://www.myminifactory.com/object/3d-print-steady-rest-for-lathe-23206 This is a steady rest for sieg c1 lathes. These lathes are also rebranded under different names. parts needed 2 m5…
This is a remix of my Mauser lug lapper. I've made several improvements to the design. It's now modeled in cad with easy to change parameters so it can easily be adapted to different actions. This is for a large ring Mauser with a 1.1"…
The Bowden coupler for on the extruder of my jgaurora a5 broke. The original design had m6 and m10 couplers but the jgaurora a5 needed a m8. Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 100% Category: 3D…
This is for a small ring Mauser with a .98" 12tpi thread. It will also work with Gewehr 88s. The plunger is a welding tip from a Bernard q-gun. A 5/16" bolt could also be modified to work. The plunger can be 3d printed.…
This is a bolt handle for a Thompson m1a1. The original model was made by Darren S on GrabCAD. https://grabcad.com/library/thompson-bolt-handle I'm using it in an airsoft Thompson with a real deactivated bolt. The original handle fit, but…
This is an adapter to use a Thompson 1928 bolt in a m1a1. I'm using it in an airsoft aeg to make a dummy replica. I started with a 1928 bolt by MikeS on GrabCAD. I reworked it using dimensions from a real m1a1 bolt. I moved the charging…
This is to replace the curved front lens with at flat 2" x 4-1/4" lens. This is for a save phace welding helmet. Two clear lenses are needed and sandwith the autodarkening lens. The orginal lens holder had some gaps that allowed light…
This extension slides over the paddle release and held on with a set screw. It allows the paddle to be easily pressed with the trigger finger. Version 2 is bigger to make it easier to push with the nail side of the finger. This allows you…
This is a printable mag vice block for HK33 style rifles. The mag vice block can be clamped into a vice. Then the rifle can be locked onto the block. The mag catch locks onto the block. This allows the rifle to be worked on or cleaned…
This is a plug for the Ruger MKIV pellet gun frame to be able to use real grips. Both the grips and the frame will need slight modifications to fit. Remove some of the wood until the grip will lay flat on the frame. The area around the…
I remixed this to either be drilled and tapped for a 3mm bolt or to insert a 3mm nut. The nut might be tight to press in. I just used a hot soldering iron to heat up the nut and melt the plastic around it. Print Settings Supports: No…
This is a top loading mag holder for m14 mags. M1a and bm59 mags might also fit. Check out the main page for Open Armory for more information on the system. Also check out the remix section for more mounts.…
This is a 3d printable tool for lapping the locking lugs on a bolt for a large ring mauser. I used a 3/8" spring 1-1/4" long. A 1/2" bolt 1/2" long is used to adjust the tension on the spring. I have included a 3d printable bolt for those…
This is a driver for a 8" lathe's compound slide. It slides onto a 1/4" hex shanked 3/8" socket adapter. Then a drill or power screwdriver can turn the slide. It will work with ether on or two of the handles installed. I've been using it…
mag_holder_mp40 is for holding mp40 mags. It will also hold mags from a MGC68 and Vigneron. mag_holder_mp41 is for holding Marushin mp41 mags. mag_holder_mp40_gsg is a holder for GSG 9mm mags. Should also work with .22lr and airsoft…
I'm installing the turn signal fascia on my Can-Am Outlander. The 2 little running lights are pretty expensive for what they are. I chose to use some universal 3/4" lights. The lights fit the hole, but are very loose. I printed the washer…
This is the dog tags for Pt. Hudson from the movie Aliens. It was modeled off of a picture of the screen used tags. In the movie he is called Pfc, but his tags say Pt. There are 2 version available. One with the engraving on the back side…
This is an adapter to use a t8 lead screw on a Da Vinci printer. The printer will either need to be flashed with repetier firmware or have a new control board. I used an anti backlash t8 nut. After printing tap the 4 holes for the nut…
A top loading mag holder for a sten. Also fits NorthEast airsoft mags Check out the main page for Open Armory for more information on the system. Also check out the remix section for more mounts. https://www.thingiverse.com/thing:3562433…
This is a remix of shop and math's lathe bit grinding jig. It's for making 55 degree whitworth threads. There's a 1/2", 3/8", and 1/4" jig. The Fusion 360 file is included. In the user parameters size sets the dimension of the lathe bit.…
This is a drilling jig and template for making a type 1 Thompson grip mount out of 1/4" plate and 5/16" socket head cap screws. When using the horizontal grip, the mount is completely hidden. The template was glued onto 1/4" plate with…
I have a Shoei stg44 that I'm rebuilding. The wood grips are missing. The set of reproduction ones I have don't quite fit. Since I'm going for a late war with mixed finish look I though bakelite grips would look good. Started with a…
This is a spacer for installing helper hinges on the CanAm LinQ 32gal trunk. With the helper hinges installed the lid stays up without the need of the flimsy kickstand. The spacers are needed because the holes in the helper springs are…
This is a model of a welding tip for a Bernard q series mig welding gun. I have several used tips that I want to use as stock for turning some parts on my cnc lathe. I drew up the tip in Fusion 360. Then imported the and aligned the part…
My jgaurora a5 arrived with the z couplers broken. Made this work so I could start using the printer. After several days of continuous printing it looks like it can be a permanent fix. The original 8mm nut was to large to fit through the…
This is a printable bondtech style extruder for Wanhao duplicator 6 or Monoprice maker ulitmate printers. It can be installed or removed from the printer without disassembling the extruder. Just remove the tension screw and flip the idler…
This is a holder for 1/2" shank drill bits. I mounted a post drill to a column and figured that it would be a good idea to store bits next to the drill. The holder can hold up to 12 drill bits. The holder is zip tied to the column. It is…
These are replacment feet for Vornado fans. Vornado_foot.stl should be printed with tpu. My printer was having problems printing tpu so I made a mold for casting rubber feet. I mixed silicone with cornstarch and pressed it into the mold.…
This adaptor allows a Kirby turbo groom attachment to attach to a Rainbow vacuum hose. Print Settings Supports: No Resolution: .2 Infill: 0% Notes: Print with 4 shells Category: Household
Did some slicing and resizing of the echo device to use it as a control panel for the interior of a printed Rhino. https://www.printables.com/model/343328-detailed-rhino-center Category: Toys & Games
Combined a Infrared Thermometer holder with a screwless stacker for ikea lack tables Print Settings Supports: No Infill: 10% Notes: The part can be mirrored to fit on the opposite side. Category: 3D Printer Accessories
To wszystkie aktualnie dostępne wyniki.
